PPDF16000/PPDF18000 PPDF14520/PPDF14520W You can find important information and FAQs about this and other products online at: www.abus.com Version 1.1 English translation of the original German instruction manual. Retain for future reference.
English Introduction Dear Customer, Thank you for purchasing this product. ABUS Security-Center hereby declares that the products PPDF16000 and PPDF14520 comply with RED Directive 2014/53/EU. Additionally, this device complies with the requirements of the following EU directives: EMC Directive 2014/30/EU and the RoHS Directive 2011/65/EU. The full EU Declaration of Conformity text can be found at: www.abus.com/product/PPDF16000 www.abus.com/product/PPDF18000 www.abus.com/product/PPDF14520 www.abus.
English Contents 1. Scope of delivery .............................................................................................................................. 4 2. Description of hardware ................................................................................................................... 5 3. 4. 2.1. PPDF16000 – Monitor ............................................................................................................. 5 2.2. PPDF18000 – Recorder .....................
English 1. Scope of delivery PPDF16000 7" monitor Power supply unit, 5 V DC/3 A (EU, UK) Power supply unit, 5 V DC/1.5 A (EU, UK) Antenna Network cable Wireless outdoor camera Wall bracket Installation material Quick guide PPDF14520 Wireless outdoor camera Power supply unit, 5 V DC/1.5 A (EU, UK) Antenna Wall bracket Installation material Quick guide PPDF18000 Recorders Power supply unit, 12 V DC/2 A (EU, UK) Power supply unit, 5 V DC/1.
English 2. Description of hardware 2.1. PPDF16000 – Monitor 1 Link LED 2 Power LED 3 On/Off switch 4 Antenna connection (RP-SMA) 5 USB interface 6 Loudspeaker 7 Stand 8 LAN interface 9 Reset button 10 MicroSD card slot (max.
English 2.2. PPDF18000 – Recorder 1 LAN interface 2 HDMI interface 3 Antenna connection (RP-SMA) 4 On/Off switch 5 MicroSD card slot (max.
English 2.3. PPDF16000 – Camera/PPDF18000 – Camera/PPDF14520/PPDF14520W 1 IR LEDs 2 Lens 3 Link LED 4 PIR sensor 5 Mount 6 Power LED 7 Stand 8 Antenna connection (RP-SMA) 9 Pairing button 10 Power supply (5 V DC/1.
English 3. Description of hardware functions 3.1.
English 4. Mounting/installation IMPORTANT! The camera must be disconnected from the power supply during installation. 4.1. PPDF16000 – Monitor Unfold the stand and lock it in place by pushing it upwards. If you want to access the device externally, connect your router to the monitor with a network cable. Then connect the 5 V DC/3 A power supply unit provided. 4.2. PPDF18000 – Recorder If you want to access the device externally, connect your router to the recorder using a network cable.
English 4.3. PPDF16000 – Camera/PPDF18000 – Camera/PPDF14520/PPDF14520W Position the mount where you intend to install the camera. Mark up and drill the required holes. Next, use the screw anchors and screws provided to fasten the mount in place. Next, install the camera on the mount by screwing the camera clockwise on to the thread. As soon as the camera is fully screwed into position, lock the camera further into place by tightening the wing nuts from underneath.
English 4.4. Pair camera The camera included in the PPDF16000 set or PPDF18000 set is already paired with the monitor and does not need to be paired again. If you would like to pair a second camera, proceed as follows: 1. Expand the live menu list and open the main menu 2. Select camera settings 3. Select the desired channel 4. Select “Pair new camera” – a window with a countdown will appear 5.
English 7. Local user interface 7.1. Operation PPDF16000 The monitor can be operated using touch input. General operation Please note that when using the touch display, it can take the monitor up to approx. half a second to process inputs. PPDF18000 The recorder can be operated using the mouse provided. Use the left mouse button to make a selection, and the right mouse button to exit the current menu. 7.2. Live display Quad display: Click on a channel from the quad display to view it in full screen.
English 7.3. Live indicators In live view mode, you will be provided with the following information: Selection This symbol indicates the camera currently selected. The audio transmission always comes from the selected camera. To start audio transmission from another camera, select the camera by clicking on it.
English Signal strength display Very weak connection Weak connection Strong connection Very strong connection If a weak or very weak connection is shown, try to improve the connection by adjusting the alignment of the antennae on the camera and monitor or recorder. If the connection does not improve, we recommend our TVAC17520 signal amplification kit: https://www.abus.com/product/TVAC17520 You can hide this display from the system settings Timestamp display Display of the current system time.
English 7.4.
English 7.5. Main menu Back Please note that you can leave individual menu items using the bottom right return button. Changes are saved automatically.
English 7.6. Camera settings Select channel Select the desired camera channel Pair new camera After pressing the button again, a window with a countdown will appear. During the countdown, press the pairing button on the camera for five seconds. If the connection was successful, a new window will appear confirming the process. Once the connection has been made, it will remain unchanged. If you want to change the camera to another channel, you will have to pair it again.
English 7.7. Recording settings Recording schedule Here you can select a schedule for a single camera or for all cameras. You can choose five different time periods for each schedule. Use the and symbols to change the respective tiles. Select the first tile to set the recording type. Motion detection Recording starts if motion is detected during the defined time period. Continuous recording Recording starts and ends according to the defined time period.
English Motion detection sensitivity Here you can select the motion detection sensitivity. PIR Motion is detected by the PIR sensor. PIR and motion detection (low) Low-sensitivity motion detection via the PIR sensor and detection software. PIR and motion detection (medium) Medium-sensitivity motion detection via the PIR sensor and detection software. PIR and motion detection (high) High-sensitivity motion detection via the PIR sensor and detection software.
English 7.8. Event list Camera channel Select the desired camera channel. Only those recordings that correspond to the selection will be displayed. Display recordings from camera 1 Display recordings from camera 2 Display recordings from camera 3 Display recordings from camera 4 Display recordings from all cameras Day selection Select the day of the recording. Days that contain recordings are marked with a “*”.
English Arrow buttons Navigate the list using the up and down arrow keys. Select event Select the time period for the recordings. Then select an event. Click the camera symbol to play back the event. Recordings from camera 1 Recordings from camera 2 Recordings from camera 3 Recordings from camera 4 Recordings from all cameras Select event Click the checkbox to select the event. Now you can take further actions.
English 7.9. Playback While playing back a channel, the current live images from the other channels are shown to you at the same time. You can enter and exit full screen mode by clicking on playback.
English 7.10. System settings Date and time Here you can select the date and time using the arrow buttons. Reset settings/language Here you can select the system language. The system will then revert to its factory settings. To easily perform a factory reset, select the same language and exit the menu. Screen display Here you can select the screen display for the cameras.
English Energy saving mode Here you can configure the settings for energy-saving mode. Energy saving mode after five minutes Energy saving mode after ten minutes Screen always on The screen switches off in energy-saving mode. It is switched back on either by manual touch input or when motion is detected. 7.11. Storage settings Storage medium Select the storage medium for the recordings and enable/disable the cycle recording function.
English Format storage medium Select the storage medium that you want to format. Format external USB hard drive Format SD card During formatting, all existing data on the storage medium is deleted. Network settings To connect to the internet and access the recorder via the app, connect the recorder to your router using the network cable. Choose between static IP and DHCP. DHCP: With this setting, the DVR automatically receives an IP address from the router.
English 8. ABUS OneLook – External operation 8.1. General information By default, the system will select the widely-used UPnP (Universal Plug and Play) solution. If your router supports this function, you should enable it in order to improve connection quality. If your router does not support this function, the system will select another connection method by default. This can have a negative effect on connection quality.
English 8.4. Device list Add Select the “+” symbol to add a device. Edit device Select the “i” symbol to edit an existing device. Delete device Swipe the device to the left to show the delete button. Press the delete button to delete the device. 8.5. Add device Device name Assign a name to your device. DID Enter the DID manually or scan the QR code on the device. Scan DID Scan the QR code on the device for a simple way to enter the DID.
English 8.6. Live view Settings Opens the settings. Please note that when accessing the settings via the app, the device will not locally display live images until the settings have been exited via the app. Push notification Opens the push notification menu. Event list Opens the event list. Manual recording Starts manual recording of the cameras. Cancel connection Cancels the connection. The device list can only be accessed once the connection is cancelled.
English 8.7. Settings You have the same options in the settings on the app as in the settings on the device itself. Please refer to the settings in the description in point 7.
English 8.8. Push notification settings Register smartphone/tablet Open the push notification menu in live view mode. Enable push notifications and enter a name for your smartphone/tablet. A name must be entered to register the smartphone/tablet. Use a separate name for each smartphone/tablet. Press “Done” to register the smartphone/tablet to the device. To remove the smartphone/tablet, open the menu again, disable push notification and press “Done”.
