AIRCOM SERIES COMPONENT COOLING SYSTEM USER MANUAL
WELCOME Thank you for choosing AC Infinity. We are committed to product quality and friendly customer service. If you have any questions or suggestions, please don’t hesitate to contact us. Visit www.acinfinity.com and click contact for our contact information. EMAIL support@acinfinity.com WEB www.acinfinity.
MANUAL CODE AC2010X1 PRODUCT AIRCOM S6 AIRCOM S7 AIRCOM S8 AIRCOM S9 AIRCOM S10 AIRCOM T8 AIRCOM T9 AIRCOM T10 4 MODEL AI-ACS6 AI-ACS7 AI-ACS8 AI-ACS9 AC-ACS10 AI-ACT8 AI-ACT9 AC-ACT10 UPC-A 854759004624 854759004631 854759004648 854759004655 819137020320 854759004662 854759004679 819137020313
MANUAL INDEX Manual Index ................................................................................. Page 5 Product Requirements ................................................................... Page 6 Key Features ................................................................................. Page 8 Product Contents ........................................................................... Page 9 Product Setup ................................................................................
PRODUCT REQUIREMENTS The AIRCOM series is designed to cool various AV components by accelerating the intake of cool air and outtake of heat. Please make sure that the following requirements are met to ensure the cooling system will work effectively. FULLY ENCLOSED CABINETS The cooling system is not compatible with fully enclosed cabinets. Air must be able to travel in and out of the cabinet. Please make sure that your cabinet has ventilation holes or is open at the front or back.
PRODUCT REQUIREMENTS WEIGHT LIMITATIONS AIRCOM S6, and S7 can support a top weight limit of 10 pounds. AIRCOM S8, S9, S10, T8, T9 and T10 can support a top weight limit of 30 pounds. Please make sure that the component does not block the cooling system cooling system’s vents. OPERATION LIMITATIONS The fan system has an operating temperature rating of 32° F to 140° F and a humidity rating of 35% to 85% RH. Please make sure that the system’s environment does not exceed these parameters.
KEY FEATURES 8 STEEL ENCLOSURE Cold-rolled steel enclosure enables additional AV components to be stacked on top of the cooling system. NOISE REDUCTION New and improved noise reduction using gaskets that absorbs noise caused by the fan’s vibrations. S SERIES CONTROLLER Features fan speed control and a pre-set temperature trigger that turns the fans on at 88° F and off at 84° F. EXPANDABLE PORTS* AIRPLATE and MULTIFAN fans can be plugged into the unit to share temperature and fan speed settings.
PRODUCT CONTENTS AIRCOM S6 AIRCOM S7 AI-ACS6 AI-ACS7 COOLING FAN SYSTEM (x1) POWER ADAPTER (x1) AIRCOM S8 AI-ACS8 AIRCOM S9 AI-ACS9 AIRCOM S10 AC-ACS10 COOLING FAN SYSTEM (x1) AIRCOM T8 AIRCOM T9 AIRCOM T10 POWER ADAPTER (x1) AI-ACT8 AI-ACT9 AC-ACT10 COOLING FAN SYSTEM (x1) POWER ADAPTER (x1) 9
PRODUCT SETUP STEP 1 Insert the AC plug of your power adapter into a power outlet. STEP 2 Plug the male connector of the adapter into the female connector located on the backside of the cooling fan system.
PRODUCT SETUP STEP 3 Place the cooling fan system on top of your AV component. STEP 4 Set up the cooling fan system’s temperature and speed settings on the control module. Refer below to see the model and instructions to follow. AIRCOM S6, S7, S8, S9, S10 Please refer to Page 12 for instructions. AIRCOM T8, T9, T10 Please refer to Page 14 for instructions.
PROGRAMMING AIRCOM S6 S7 S8 S9 S10 MODE CONTROL BUTTON Pressing this button will cycle through the modes: ON Mode, AUTO Mode, SMART Mode, OFF Mode. AUTO MODE LIGHT This orange light indicates if the system is running in AUTO Mode. SPEED CONTROL BUTTON Pressing this button changes the speed settings while the fans are running in ON, AUTO, and SMART Mode. FAN SPEED LIGHT Indicates fan speed; and also the speed settings of AUTO and SMART Mode.
PROGRAMMING AIRCOM S6 S7 S8 S9 S10 MODE CONTROL Pressing the Mode Control button will cycle through the operating modes: ON Mode, AUTO Mode, SMART Mode and OFF Mode. ON MODE - A white light as shown on page 12 indicates if the system is running in ON Mode. In this mode, the fans will run continuously regardless of temperature. AUTO MODE - An orange light as shown on page 12 indicates if the system is running in AUTO Mode.
PROGRAMMING AIRCOM T8 T9 T10 1. MODE BUTTON Cycles through the unit’s modes: AUTO, SMART, OFF, ON, ALARM. Holding for three seconds will lock or unlock the display. 1 2. UP / DOWN BUTTON The up and down buttons changes the setting temp, alarm temp, display brightness, or the speed of the fan. 4 7 3 5 3. LEAF BUTTON This turns the display off while programs run in the background. Holding will change degrees to Fahrenheit or Celsius. 6 2 8 9 4.
PROGRAMMING AIRCOM T8 T9 T10 QUICK START Press the MODE button until you are on AUTO mode. This mode works like a thermostat. Then press the up and down triangle buttons to change the SETTING temperature on the screen. The PROBE temperature is what the thermal probe is measuring. When the PROBE temperature exceeds the SETTING temperature, the fans will start running. ON MODE In this mode, the fans will run non-stop regardless of temperature.
PROGRAMMING AIRCOM T8 T9 T10 OFF MODE In this mode, the fans are powered off regardless of set temperature or set speed. The backlight setting can be increased or decreased by pressing the up or down buttons while in this mode. If the first and the third brightness bar light up and the device is left unattended for 30 seconds, the display will automatically dim its brightness back to the dimmest setting. SMART MODE This is the energy saving mode where the fans will change speed depending on the temperature.
PROGRAMMING AIRCOM T8 T9 T10 ALARM SETTING In this mode, you can set what temperature the system’s alarm will trigger by pressing the up and down triangle buttons. When the PROBE temperature reaches or exceeds the ALARM temperature, the alarm will activate. The alarm will only activate while the controller is in ON, AUTO, or SMART Mode so please remember to exit ALARM Mode once the alarm has been set.
PROGRAMMING AIRCOM T8 T9 T10 VARIATION BUFFER In AUTO mode, a buffer is built in to prevent your fan from turning on and off too quickly due to small variations in the environment. When the PROBE temperature exceeds your SETTING temperature, the fan will start running immediately. However, the PROBE temperature will need to fall below your SETTING temperature by 4° Fahrenheit or 2° Celsius or more, to stop the fans from running.
PROGRAMMING AIRCOM T8 T9 T10 ALERT ICONS On the bottom right of the display there are three alert icons. They are visible to show that the system’s functions are being monitored. They will flash when the controller wishes to alert you that a particular function is being triggered. CHECK FAN ALERT The check fan icon will flash when the fan’s sensor detects interference to its operation. Please check the fan for possible issues.
AIRCOM FAQ Q: Is this fan capable of being rack mounted? A: This fan is not specifically designed to be mounted in rack cabinets. Q: How many fans can I connect to the expansion USB ports? A: You may connect up to two MULTIFANs per USB port. This feature is only available in the AIRCOM T-Series. Q: What is the biggest load I can stack on top of the AIRCOM? A: 12” models can take up to 10 pounds of electronics and equipment on top of it. 17” models can take up to 30 pounds.
AC INFINITY PRODUCTS AIRPLATE SERIES The AIRPLATE series is designed to cool home theater and audio video cabinets. The fans are powered by USB port or power outlets. Includes an inline speed controller and Boost Speed Adapter. The fans can also be temperature controlled with an Advance Thermal Controller (sold separately). PRODUCT AIRPLATE S1 AIRPLATE S3 AIRPLATE S5 AIRPLATE S7 AIRPLATE S9 MODEL AI-CFS80BA AI-CFS120BA AI-CFD80BA AI-CFD120BA AI-APS9 DIMENSIONS 4.6 x 4.6 x 1.3 in. 6.3 x 6.3 x 1.3 in. 8.
WARRANTY This warranty program is our commitment to you, the product sold by AC Infinity will be free from defects in manufacturing for a period of two years from the date of purchase. If a product is found to have a defect in material or workmanship, we will take the appropriate actions defined in this warranty to resolve any issues. The warranty program applies to any order, purchase, receipt, or use of any products sold by AC Infinity or our authorized dealerships.
COPYRIGHT © 2021 AC INFINITY INC. ALL RIGHTS RESERVED No part of the materials including graphics or logos available in this booklet may be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine readable form, in whole or in part, without specific permission from AC Infinity Inc.