Installation Guide

(1) TOOLS AND MATERIALS REQUIRED
 BLADE SCREW DRIVER
 ADJUSTABLE WRENCH
 STEP LADDER
 WIRE CUTTERS
 WIRING SUPPLIES AS REQUIRED BY ELECTRICAL
CODE
Attention:
Before assembling your lighting fixture, please read the
following instructions. If you feel you do not have sufficient
electrical experience, refer to a do-it-yourself wiring handbook
or have your fixture installed by a qualified licensed electrician.
(2) GENERAL
1. To ensure the success of the installation, be sure to
read these instructions and review the diagrams
thoroughly before beginning.
2. All electrical connections must be in accordance with
local codes, ordinances, or the National Electrical
Code. If you are unfamiliar with methods of installing
electrical wiring, secure the services of a qualified
licensed electrician.
These fixtures are intended for mounting to a standard 4” x
2 ¼ ” deep metal octagon outlet box. The box must be
directly supported by the building structure and U.L
Recognized.
3. Before commencing with the installation, disconnect
the power by turning off the circuit breaker or
by removing the fuse at the fuse box. Turning the
power off using the light switch is not sufficient to
prevent electrical shock.
NOTE:
The important safeguards and instructions appearing in this
manual are not meant to cover all possible conditions and
situations that may occur. It must be understood that common
sense, caution and care, are factors that cannot be built into any
product. These factors must be supplied by the person(s) caring
for and operating the fixture.
(3) UNPACKING THE FIXTURE
On checking the contents of the box you will find;
 Fixture assembly
 Glass Diffuser w/Metal Cover
 1 or 2 x 50W/120V/MR16/GU10 Base Bulb
 Mounting hardware package
 1 x Waterproof Gasket
(4) PREPARE THE FIXTURE
Refer to figure I for illustration of fixture parts and assembly.
1. If you are replacing an existing fixture, disconnect and
remove the old fixture. Expose the supply wiring from the
outlet box.
2. Lay the un-assembled fixture on a soft surface and
carefully remove all the packaging material.
3. Mount the supplied Universal Crossbar to the Junction
Box with the Mounting Screws (2).
4. Pull the Supply Wires through the center hole of the
Universal Mounting Plate.
Connect the Supply Wires from the junction box to the
Fixture Wires in the following manner: The Black Supply
Wire attaches to the Black Fixture Wire and the White
Supply Wire attaches to the White Fixture Wire. Attach the
Ground (bare/green or yellow) wire from the Fixture to the
Outlet Box Ground Terminal or (the box ground wire).
Secure the connections with the supplied Wire Nuts (3) and
tape with electrical tape. Tuck all of the wires carefully into the
J-box.
5. If the Waterproof Gasket (1) is not already inserted,
ensure that it is placed in the area allocated on the inside
of the Fixture Back Plate.
6. Place the Fixture Back Plate flush up against the
Universal Crossbar, by ensuring the protruding Screws
on the Universal Crossbar are inserted into the
designated holes in the Fixture Back Plate.
7. Secure the Fixture Back Plate to the Universal
Crossbar with the supplied Nuts (4) and Thumb
Screws (5)
8. Insert the 50W/120V MR 16/GU-10 base bulb(s) (6)
provided. Screw on the Glass Diffuser(s) with Metal
Ring(s); tighten to ensure that they are secure.
DO NOT USE BULBS EXCEEDING MAXIMUM
WATTAGE AS PER LABEL
NOTE: Outdoor wall fixtures must be caulked with
suitable PTV or silicone compound around the top
and sides of the cover plate to reduce the chance
of water entering into the splicing area.
9. Restore electricity and check the operation of your new
lighting fixture.
CAUTION:
 Ensure that the Fitting is Cool and Switched off,
Before Changing the Halogen Bulb.
 Do Not use Bulbs Exceeding Maximum Wattage, As
Per Caution Label.
 Do Not use lamp without the supplied Tempered
Protection Glass.
 Do Not Touch the Halogen Bulb or Protective Glass
while fixture is in operation.
 Do Not Operate the Lighting Fixture close
to any Combustible Material.
***READ & SAVE THESE INSTRUCTIONS ***
MODELS 23025/23026
INSTALLATION & OPERATION INSTRUCTIONS