Installation Sheet

ManualsBrandsAccess Lighting ManualsLightingTabo 1-Light Brushed Steel Vanity Light with Opal Glass Shade

WHAT YOU NEED

•

Screwdriver

• Wire Cutters

• Wiring Supplies as Specified

by Electrical Code

• 1 x 60W/E12/Candelabra

WHAT WE PROVIDE

•

Crossbar

• Mounting Hardware

• Back Plate

• Metal bar

• 1 x Glass Shade

COLLECTION

CERTIFICATION: cULus DAMP NO. 50182

50182

APPLICATION MODEL NO.

Wall Fixture

Tabo

IMPORTANT SAFETY INSTRUCTIONS

Before assembling your ACCESS LIGHTING fixture, please make sure that

you carefully read through this instruction sheet.

CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH

CIRCUIT CONDUCTOR.

CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES

CONDUCTEURS DE LA DERIVATION SONT ADEQUATS

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONTSTRUCTION

AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT,

PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT

AINSI QUE LES RISQUES INHERENTS

NOTE: The important safeguards and instructions that appear in this

manual are not meant to cover all possible conditions and situations

that may occur. It must be understood that common sense, caution and

care, are factors that can’t be built into any product. These factors must

be supplied by the person(s) caring for and operating the fixture.

SAVE THESE INSTRUCTIONS AND REFER TO THEM WHEN ADDITIONS

TO OR CHANGES IN THE FIXTURE CONFIGURATION ARE MADE.

Read all instructions

Do not install this fixture in hazardous locations

Do not install any fixture assembly closer than 6 inches from any

curtain or similar combustible material

STEP BY STEP INSTRUCTIONS

Before starting your installation disconnect the Power by turning off the

Circuit Breaker or by removing the fuse at the fuse box. Just turning the

light off at the light switch is not sufficient to prevent electrical shock.

GENERAL INFORMATION

All electrical connections must be in accordance with all ordinances,

Local and National Electrical Codes. These fixtures are intended for

mounting to a standard 4” x 2 1/2”metal octagon outlet box. The box

must be directly supported by the building structure and U.L. Recognized.

INSTALLATION INSTRUCTIONS

Summary of content (3 pages)

PAGE 1
CERTIFICATION: cULus DAMP NO. 50182 INSTALLATION INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Before assembling your ACCESS LIGHTING fixture, please make sure that you carefully read through this instruction sheet. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.
PAGE 2
CERTIFICATION: cULus DAMP NO. 50182 1 2 MOUNT CROSSBAR If there is an existing fixture remove it. Expose the supply wires from the j-box. Mount the crossbar to the j-box. Gently pull the wires through the center hole in the crossbar. CONNECT THE WIRES Gently pull the supply wires. Connect the black supply wire the black fixture wire. Secure with the supplied wire nuts. Connect the white supply wire to the white fixture wire. Secure with the supplied wire nuts.
PAGE 3
CERTIFICATION: cULus DAMP NO. 50182 4 5 MOUNT THE METAL BAR Place the metal bar up to the back plate inserting the sockets into the designated holes in the metal bar. SECURE THE GLASS SHADE Secure the glass shade to the fixture, by aligning the holes the glass with the sockets. Insert the sockets into the glass. Secure with the supplied socket ring. Insert the bulb. MAXIMUM WATTAGE 60W. DO NOT EXCEED THE MAXIMUM WATTAGE AS STATED ON THE WARNING LABEL AND INSTRUCTION SHEETS.