Owner manual

ManualsBrandsAcclaim Lighting ManualsSoftwareX-Power TV

User Instructions

Descriptions:

24-004-1915-00

Rev 2.0

Congratulations with your purchase of this product.

Read this manual carefully before using our Acclaim Lighting X-Power TV. The X-Power TV is a combination

of a control interface and tension provider for our X-CHIP LED PCB modules. A maximum of 24 channels

can be controlled separately. Its high frequency function is suitable for CCD cameras pick up facility.

Check for transport damage.

You should be in possession of the following items:

1 X-Power TV

1 manual

Should you discover transport damage after unpacking the equipment, inform the hauler immediately.

Never connect a damaged device. You may also contact your supplier.

Delivery packet:

Controls & Functions:

Rear panel view

5. DMX LED

Green LED (flashing) indication for DMX signal.

Quick flashing: an Acclaim Lighting Setup tool is updating.

Slow flashing: DMX signal active.

6. Power LED

Red LED (power) indication for presence of tension.

7. DMX / Programming input

XLR chassis part male, 3-polar for DMX connection.

8. DMX output/Thru (connection)

XLR chassis part female, 3-polar for DMX through.

Front panel view

1. Fuse holder Fuse T3.15A 250V 5x20mm

2. Power In AC110-120V, 3.2A/ AC220V-240V, 1.6A 50/60Hz, 150W

3. Selection tension Selection of tension

4. Power switch ON/OFF

AC110-120V/ AC220V-240V,50/60Hz, 150W

Acclaim Lighting - Los Angeles, CA 90058

www.acclaimlighting.com

Serial Number:

CAUTION

Risk of Electric Shock

DO NOT OPEN

Ne pas ouvrir. Risque de choc electrique

Warning :

This unit must be grounded

POWER IN:

110-120VAC, 3.2A / 220-240VAC, 1.6A

50/60Hz 150W

FUSE:

T3.15A 250V 5x20mm

VOLTAGE-SELECT

Made in PRC

POWER

FUSE

POWER IN

115V

DMX IN

POWER

DMX

THROUGH

1=Ground

2=Data-

3=Data+

OUTPUT: 6A/CH. TOTAL 6A MAX.

Blue

Red

Green

+24V

GND

Blue

Red

Green

+24V

GND

Blue

Red

Green

+24V

GND

Blue

Red

Green

+24V

GND

Blue

Red

Green

+24V

GND

Blue

Red

Green

+24V

GND

Blue

Red

Green

+24V

GND

Blue

Red

Green

+24V

GND

PUSH

5 6

Summary of content (6 pages)

PAGE 1
User Instructions Descriptions: Congratulations with your purchase of this product. Read this manual carefully before using our Acclaim Lighting R X-Power TV. The X-Power TV is a combination of a control interface and tension provider for our X-CHIP LED PCB modules. A maximum of 24 channels can be controlled separately. Its high frequency function is suitable for CCD cameras pick up facility. Delivery packet: Check for transport damage.
PAGE 2
9. 24V DC outputs 8 terminal output connector, 5-polar for connecting X-CHIP LED modules 24V DC. Note: Never connect the DMX signal and the Setup Tool to an XLR 3-polar input or output simultaneously. This can severely damage your X-Power TV. Connecting the tension provider: Check whether or not the Voltage Select switch has been set correctly. Note: If Voltage Select is set to 110V, do NOT connect a 230V power supply. This can severely damage your X-Power TV.
PAGE 3
Programming: A Setup Tool (depicted here programmer_XB-R1) is required to program the X-Power TV. For further information, please refer to its accompanying manual. A Setup Tool(XB-R1) (Sold separately) 1. Slave Control(DMX Mode) In Slave Control, the settings for the addresses(001-512) and the Glide Effect functions can be adjusted with a Setup Tool. There are 12 work modes for Slave Control.
PAGE 4
MODE-5 Patch mode C&B of 16 outputs---->8 outputs(4x2 channels) 4 C&B mode: has 4 groups with C&B output, of which each group consists of 2 outputs that are controlled by 2 channels(8 channels in total).
PAGE 5
Color (R/G/B) Channel 1-3 Red Group 1/ Output 1-8 1 2 Blue 3 MODE-11 Patch mode C&B of 16 outputs---->2 outputs(2x1 channels) 1 C&B mode: has 1 group with C&B output, which consists of 8 outputs that are controlled by 2 channels. Channel 1-2 C&B Group 1/ Output 1-8 Color 1 Brightness 2 MODE-12 Patch mode Color of 8 outputs---->1 outputs(1x1 channels) 1 COLOR mode: has 1 group with Color control, which consists of 1 output that is controlled by 1 channel. The brightness is always 100%.
PAGE 6
Technical details: Tension/capacity: Fuse: Inputs: AC110-120 V, 3.2A / AC220-240V,1.6A, 50/60Hz 150W 3.