SERVICE MANUAL MODELS: GBC GLS28, GLX20, GLM11, GLHS9 REXEL RLS28, RLX20, RLM11, RLSM9 (2008.12.
© 2008 All Rights Reserved No part of this publication may be reproduced in any form without expressed written permission from Electronically Printed and Designed in the USA.
Table of Contents INTRODUCTION 1 SPECIFICATIONS INSTALLATION 2 TROUBLESHOOTING 3-7 DISASSEMBLY/ADJUSTMENTS 8-9 MAINTENANCE 10.
Introduction Introduction 11 a a g g e d f e d f b c c Models: GBC GLS28, GLX20 / REXEL RLS28, RLX20 a b c d e f g Models: GBC GLM11, GLHS9 / REXEL RLM11, RLSM9 Indicator Panel Door for Bin Wheels Power On Button Auto Feed Button Reverse Button CD Slot 1 Illuminated Panel 1 2 3 4 b Power On Shredder not OK Door Open Bin Full 2 3 4
Specifications 2 Specifications Models GLS28 GLX20 Sheet Capacity - 28 sheets 20 sheets Duty Cycle - Continuous operation Continuous operation Volts / Hz 120V AC / 60Hz 120V AC / 60Hz Amperage 8.0 A 10.0 A Models GLM11 GLHS9 Sheet Capacity - 11 sheets 9 sheets Duty Cycle - Continuous operation Continuous operation Volts / Hz 120V AC / 60Hz 120V AC / 60Hz Amperage 10.0 A 8.
5.0 TTroubleshooting Mechanical Operation The shredder uses two rotating cutting shafts, which are driven by an electrical motor to shred paper. Electrical Operation Bag Full Flap Switch - The flap switch is a normally open switch actuated by the bag full flap. When the shred bag becomes full of shredded material, the bag full flap is pushed back and power is then removed from the motor circuit.
5.0 TTroubleshooting General Troubleshooting Troubleshooting Chart Malfunction corrections are based on visual observations made by the operator. The causes of the malfunctions are isolated by the symptom of the malfunction and noting at which point in the operating cycle the malfunction occurred. Malfunctions may be pinpointed to a defective electrical component or mechanical part by referring to the Principles of Operation, the troubleshooting guide and the wiring diagram.
5.0 Troubleshooting 5 Shredder Does Not Operate, No Indication Of Power Power Cord Disconnected.
Troubleshooting Power SW(PUSH) 16A/250VAC SW5 Auto-Forward 6 LED4 LED3 LED1 LED2 S1 SW6 standy by(flash GREEN)&auto(GREEN) Reverse JAM&REVERSE(RED) Bin OPEN(RED) panel board 1 2 3 4 5 6 7 8 1 2 JA1 CON3 8PIN/2.0 POWER1 5.08MM 8 7 6 5 4 3 2 1 2 1 C Paper Trigger Emitter Incept EMITTER Photo LED 2.0mm/2p 1 2 3 4 5 Paper Trigger 1 2 5.08/5P 2.5mm/2p CN1 BIN1A1 3P-2.0 2.5MM/4P BIN2A1 2P/2.
Troubleshooting Reverse Reverse 2 R18 C5 1 NEUTRAL 2 Forward R25 Forward 1 47/0.5W 0.01U/250VAC 3 4 C8 U4B QA5 SS8550 Reverse 5V SW 1N4148 5V SW MOC3063 JAM1B1 1 U4C 5 3 QA2 TMG16C80 R28 4 1K 1/4W 3 R27 5 2.2K 1/8W 74HC14_2 Forward E C PHOTO JAM DETECT R14 10k 1/8w 1 2 3 SW2 COMMON C12 D5 1.5K 1/8W + 1N4148 10UF/25V C10 R22 R30 4.7UF/25V 47K 1/8W 1K 1/8W Timmer NO TCO NC D8 DOOR SAFETY SW R40 22K/1W R40 51K/1W R41 4.
Troubleshooting 8 Necessary Tools Engine Assy. (Cutting Head Assy.) Removal 1. Adjustable wrench 2. #2 Phillips Screwdriver Disassembly of the shredder is described in the following steps. 1 Top Housing Removal 2 2 2 1. Remove the six phillip head screws that secure the main pcb box to the bottom base. 2. Remove pcb box front cover. Unplug and label all wires from main pcb box. WARNING! Disconnect the unit from the receptacle before performing any disassembly procedures. 1.
5.0 Troubleshooting Gear Box Removal External Cleaning Make sure you disconnect the shredder from its power source before cleaning. The cover and cabinet may be cleaned with a soft cloth moistened with a mild detergent and warm water. Do not use chemical cleaners or solvents as these may have a harmful e ect. Use detergent sparingly to avoid contact with electronic components.
Full Circle Service 10303 80th Avenue Pleasant Praire, Wi 53158 TM 12/18/08
