000BASE-SX Gigabit Uplink Module EM4601-SX-SC Quick Installation Guide
Quick Installation Guide EM4601-SX-SC Gigabit Uplink Module Slide-in module with 1 1000BASE-SX (SC-type) port
Copyright © 2000 by Accton Technology Corporation. All rights reserved. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Accton Technology Corporation. Accton makes no warranties with respect to this documentation and disclaims any implied warranties of merchantability, quality, or fitness for any particular purpose. The information in this document is subject to change without notice.
Contents Description of Hardware Gigabit Uplink Module Gigabit Port LEDs Installing the Module Package Contents Handling the Modules Instructions Maximum Cable Length 1 1 1 2 2 2 2 5 Troubleshooting Product Specifications 5 6 EMI Certification FCC Class A Certification (USA) Canada Department of Communications - Class A BSMI Class A (Taiwan) VCCI Class A Compliance (Japan) CE Mark Declaration of Conformance for EMI and Safety (EEC) 6 6 6 7 7 7 Safety Compliance Warning: Fiber Optic Port Safety Avertis
Contents ii
Description of Hardware Gigabit Uplink Module The EM4601-SX-SC fiber optic module is designed for use in Accton switch models which have a single-port Gigabit Ethernet transceiver slot. At present, suitable units include the CheetahSwitch Workgroup-3628 (ES3628). Detailed information about configuring these modules and advice about Fast Ethernet configuration rules can be found in the switch’s user guide.
User Guide Installing the Module Caution: Do not install this module in any unit other than the CheetahSwitch Workgroup-3628 (ES3628). Contact your distributor for advice on newly released switches which may be designed for use with these modules. The EM4601-SX-SC fiber optic module is field installable. Just follow the instructions below.
Description of Hardware Keep the original faceplate for future use. If you should remove the module, replace the faceplate to prevent dust and debris from entering the unit and to maintain proper air flow. 5. Insert the new module into the switch: Holding the new module with the text on the front panel upright, carefully slide the module into the lower right slot on the rear panel, and press gently until it snaps into place. Be sure the new module’s front panel is flush with the switch panel.
User Guide 6. Secure the new module: Secure the new module in place by screwing the attached screws clockwise into the switch’s chassis. Tighten them enough to secure the module, but not so tight as to prevent them from being unscrewed by hand. 7. Connect the network cable to the module: Connect fiber cable to the port on the newly installed module. See “Maximum Cable Length” on page 5 in this guide for further information. 8.
Troubleshooting Maximum Cable Length Cable Types and Specifications Cable Type Max. Length Connector 10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45 100BASE-TX Cat. 5 100-ohm UTP 100 m (328 ft) RJ-45 100BASE-FX 50/125 or 62.5/125 micron core multimode fiber 1000BASE-SX Half duplex 412 m (1,351 ft.) SC or ST Full duplex 2 km (1.24 miles) SC or ST 50/125 or 62.
User Guide Product Specifications Access Method Ports Network Interface Communication Mode LED Indicators Size Power Consumption Temperature Humidity Standards Compliances Emissions Immunity Warranty CSMA/CD 1 1000BASE-SX SC connector: 62.5/125 or 50/125 micron multimode fiber cable Full duplex, auto-negotiation for flow control Link, TX, RX 14.8 x 11.2 x 2.1 cm (5.8 x 4.4 x 0.83 in.) 4W maximum Operating: 0 to 50°C (32 to 122°F) Storage: -40 to 158°C (-40 to 70°F) 5% to 95% IEEE 802.
EMI Certification BSMI Class A (Taiwan) VCCI Class A Compliance (Japan) CE Mark Declaration of Conformance for EMI and Safety (EEC) This is to certify that this product complies with ISO/IEC Guide 22 and EN45014. It conforms to the following specifications: EMC: EN55022(1988)/CISPR-22(1985) EN60555-2(1995) EN60555-3 IEC1000-4-2(1995) IEC1000-4-3(1995) IEC1000-4-4(1995) IEC1000-4-6(1995) class A class A 4kV CD, 8kV AD 3V/m 1kV - (power line), 0.
User Guide Safety Compliance Warning: Fiber Optic Port Safety When using a fiber optic media expansion module, never look at the transmit laser while it is powered on. Also, never look directly at the fiber TX port and fiber cable ends when they are powered on. Avertissment: Ports pour fibres optiques sécurité sur le plan optique Ne regardez jamais le laser tant qu’il est sous tension.
Warranty 8. 9. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte auch nichts auf der Leitung abgestellt werden. 10. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten. 11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden. 12.
EM4601-SX-SC E062000-R01 150471-102
