User's Manual
Table Of Contents
- Chapter 1: Introduction 1-1
- Chapter 1: Introduction
- Chapter 2: Hardware Installation
- Chapter 3: External Antennas
- Chapter 4: Network Configuration
- Chapter 5: Initial Configuration
- Chapter 6: System Configuration
- Chapter 7: Command Line Interface
- Using the Command Line Interface
- Entering Commands
- Command Groups
- General Commands
- System Management Commands
- System Logging Commands
- System Clock Commands
- DHCP Relay Commands
- SNMP Commands
- snmp-server community
- snmp-server contact
- snmp-server location
- snmp-server enable server
- snmp-server host
- snmp-server trap
- snmp-server engine-id
- snmp-server user
- snmp-server targets
- snmp-server filter
- snmp-server filter-assignments
- show snmp groups
- show snmp users
- show snmp group-assignments
- show snmp target
- show snmp filter
- show snmp filter-assignments
- show snmp
- Flash/File Commands
- RADIUS Client
- 802.1X Authentication
- MAC Address Authentication
- Filtering Commands
- WDS Bridge Commands
- Spanning Tree Commands
- Ethernet Interface Commands
- Wireless Interface Commands
- interface wireless
- vap
- speed
- turbo
- multicast-data-rate
- channel
- transmit-power
- radio-mode
- preamble
- antenna control
- antenna id
- antenna location
- beacon-interval
- dtim-period
- fragmentation-length
- rts-threshold
- super-a
- super-g
- description
- ssid
- closed-system
- max-association
- assoc-timeout-interval
- auth-timeout-value
- shutdown
- show interface wireless
- show station
- Rogue AP Detection Commands
- Wireless Security Commands
- Link Integrity Commands
- IAPP Commands
- VLAN Commands
- WMM Commands
- Appendix A: Troubleshooting
- Appendix B: Cables and Pinouts
- Appendix C: Specifications
- Glossary
- Index
System Configuration
6-42
6
To view the current SNMP settings, use the show snmp command.
Configuring SNMPv3 Users
The access point allows up to 10 SNMP v3 users to be configured. Each user must
be defined by a unique name, assigned to one of three pre-defined security groups,
and configured with specific authentication and encryption settings.
User – The SNMPv3 user name. (32 characters maximum)
Group – The SNMPv3 group name. (Options: RO, RWAuth, or RWPriv; Default: RO)
• RO – Read-only access.
• RWAuth – Read/write access with user authentication.
• RWPriv – Read/write access with both user authentication and data encryption.
Auth Type – The authentication type used for the SNMP user; either MD5 or none.
When MD5 is selected, enter a password in the corresponding Passphrase field.
Priv Type – The data encryption type used for the SNMP user; either DES or none.
When DES is selected, enter a key in the corresponding Passphrase field.
Enterprise AP#show snmp 7-54
SNMP Information
==============================================
Service State : Enable
Community (ro) : *****
Community (rw) : *****
Location : WC-19
Contact : Paul
EngineId :80:00:07:e5:80:00:00:2e:62:00:00:00:18
EngineBoots:1
Trap Destinations:
1: 192.168.1.9, Community: *****, State: Enabled
2: 0.0.0.0, Community: *****, State: Disabled
3: 0.0.0.0, Community: *****, State: Disabled
4: 0.0.0.0, Community: *****, State: Disabled
dot11InterfaceAGFail Enabled dot11InterfaceBFail Enabled
dot11StationAssociation Enabled dot11StationAuthentication Enabled
dot11StationReAssociation Enabled dot11StationRequestFail Enabled
dot1xAuthFail Enabled dot1xAuthNotInitiated Enabled
dot1xAuthSuccess Enabled dot1xMacAddrAuthFail Enabled
dot1xMacAddrAuthSuccess Enabled iappContextDataSent Enabled
iappStationRoamedFrom Enabled iappStationRoamedTo Enabled
localMacAddrAuthFail Enabled localMacAddrAuthSuccess Enabled
pppLogonFail Enabled sntpServerFail Enabled
configFileVersionChanged Enabled radiusServerChanged Enabled
systemDown Enabled systemUp Enabled
=============================================
Enterprise AP#