Quick Start Guide

ManualsBrandsAccton Technology ManualsElectronics60GHz Long Haul terminal

– 1 –

Quick Start Guide

Scope mount

2. Alignment/Signal Strength LED Indicators

3. System LED Indicators:

■

60G: On (60GHz wireless link), Blinking (activity).

■

2.5G: On (link), Blinking (activity)

■

SFP: On (Uplink port link), Blinking (activity)

■

PWR: Slow blink during system boot up.

4. Reset button

5. Grounding Screw

6. DC IN Port

7. LAN Port

8. SFP Port

E112021-MR-R01

www.edge-core.com

60GHz Long Haul Terminal

MLTG-CN-LR

60GHz Access Point MLTG-CN-LR

2. 1 x 24 W passive PoE injector

3. 1 x Power cord

4. 1 x DC connector plug

5. 3 x Cable glands

6. Documentation QR-code card

Package Contents

2 3 61

Overview

Interface

MAC Address

LAN Port Ethernet MAC

(Printed on the device’s label)

SFP Port Ethernet MAC + 1

60 GHz Ethernet MAC + 2

Summary of content (8 pages)

PAGE 1
Quick Start Guide 60GHz Long Haul Terminal MLTG-CN-LR Package Contents 1 2 4 3 5 6 4. 1 x DC connector plug 5. 3 x Cable glands 6. Documentation QR-code card 1. 60GHz Access Point MLTG-CN-LR 2. 1 x 24 W passive PoE injector 3. 1 x Power cord Overview 1 1. Scope mount 2. Alignment/Signal Strength LED Indicators 3. System LED Indicators: ■ 60G: On (60GHz wireless link), Blinking (activity). 2.
PAGE 2
Quick Start Guide Installation Warning: For a safe and reliable installation, use only the accessories and screws provided with the device. Use of other accessories and screws could result in damage to the unit. Any damages incurred by using unapproved accessories are not covered by the warranty. Avertissement: Pour une installation sûre et fiable, utilisez uniquement les accessoires et les vis fournies avec l’appareil. L’utilisation d’autres accessoires et vis pourrait endommager l’appareil.
PAGE 3
Quick Start Guide 1. Attach the two main sections of precision bracket using two M8 25 mm bolts, flat washers, and spring-lock washers. 6. Before aiming, ensure the horizontal adjustment bolt and nut is 2. Use the M8 40 mm bolt with flat and spring-lock washers to attach tightened. The bracket is shipped with the nut in a loose position. the bracket to the vertical-adjustment mechanism. 3. Seat the four M8 125 mm bolts in the main assembly so that the 4. 7.
PAGE 4
Quick Start Guide b. Using the LC Precision Bracket 2 A 3 1 4 B Note: Do not adjust bolts A and B without first loosening 1, 2, 3, and 4 respectively. Note: It is recommended to only adjust one axis (A for vertical or B for horizontal) at a time. 4. Use a general visual estimate or the optical scope for initial alignment before starting on other adjustments. 5. Loosen the horizontal adjustment bolts 3 and 4. Use fine-tune bolt “B” to optimize the horizontal position. Re-tighten bolts 3 and 4. 6.
PAGE 5
Quick Start Guide 7 Access the Web User Interface a. Using the LAN Port 1. Connect a PC directly to the MLTG-CN-LR’s LAN port. 2. Set the PC IP address to be on the same subnet as the MLTG-CN- 3. 4. The MLTG-CN-LR can also accommodate a Picatinny Rail and corresponding widely available laser sights. 5 Connect Power a. DC Power Wire the included DC terminal plug to a 24-48 VDC, 0.5-1 A source to provide power to the MLTG-CN-LR. b.
PAGE 6
Quick Start Guide Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 22 cm de distance entre la source de rayonnement et votre corps. Safety and Regulatory Information FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 7
Quick Start Guide 警告和注意訊息警告：本產品不包括任何可由用戶維修的零件。警告：安裝或拆卸本裝置時，必須由合格的人員進行操作。警告：將本裝置連接至電源插座時，將三極電源插座上的基地場導線連接至有效的接地線，以防止出現電氣危險。注意：應佩戴防靜電腕帶或採取其他有效措施，以防止在操作本設備時出現靜電放電。注意：切勿將電話插頭插入 RJ-45 埠。否則可能導致裝置損壞。注意：請僅使用帶有 RJ-45 連接器的符合 FCC 的雙絞線。 BSMI (Taiwan) 警告使用者 : 此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被要求採取某些適當的對策。 ◆ 保持機器在乾燥的環境下使用，雨水、溼氣、液體等含有礦物質將會腐蝕電子線路。 ◆ 使用時，請務必保持周遭散熱空間，以利散熱。 ◆ 使用前，請檢查各項周邊設備是否都已經連接妥當再開機。 ◆ 避免邊吃東西邊使用，以免污染機件造成故障。 ◆ 請避免讓紙張碎片、螺絲及線頭等小東西靠近產品之連接器、插槽、孔位等處，避免短路及接觸不良等情況發生。 ◆ 請勿將任何物品塞入產
PAGE 8
Quick Start Guide Hardware Specifications AP Chassis Size (WxDxH) 355 x 355 x 315 mm (13.98 x 13.98 x 12.40 in) Weight 3 kg (6.61 lb) Temperature Operating: -40° C to 60° C (-40° F to 140° F) Storage: -40° C to 70° C (-40° F to 158° F) Humidity Operating: 5% to 95% (non-condensing) Network Interfaces Ports 2.5G Ethernet Port (PoE IN) SFP Port 60 GHz 802.11ay Power Supply PoE Input Power 48 VDC (non-standard) Power Consumption 15.9 W max. Regulatory Compliances Radio EN 302 567 V2.1.