Fast SwitcHub-8mi SNMP Advanced Reference Guide ES3508-TX E0398-R01 150849-101
Copyright © 1998 by Accton Technology Corporation. All rights reserved. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Accton Technology Corporation. Advanced Reference Guide Accton makes no warranties with respect to this documentation and disclaims any implied warranties of merchantability, quality, or fitness for any particular purpose. The information in this document is subject to change without notice.
Fast SwitcHub-8mi SNMP Contents Advanced Reference Guide Introduction Introduction 1 Making the Connections Required for System Configuration Onsite Connection Modem Connection Telnet Connection In-Band Network Connection 1 1 1 2 2 Configuring Your System with the On-Board Program 2 The on-board management agent in the Fast SwitcHub-8mi SNMP provides the switch with advanced management capabilities.
Fast SwitcHub-8mi SNMP Advanced Reference Guide Configure the Remote Site: At the remote site, connect the PC's COM port (COM 1~4) to the modem's serial port. Set terminal emulation type to VT100, specify the port used by your PC (i.e., COM 1~4), and then set communications to 8 data bits, 1 stop bit, no parity, 9600 or 19200 bps and no flow control. If this is your first time to log into the configuration program, then the default passwords are still "admin" and "guest.
Fast SwitcHub-8mi SNMP Menu Port Configuration Description Advanced Reference Guide (continued) System Configuration Disables/enables any port; sets communication mode to autonegotiation, full duplex or half duplex; sets the aging time for entries in the address table, the processing scheme for forwarding packets to adaptive cut-through, cut-through, fragment-free cut-through, or storeand-forward; and enables/disables flow control.
Fast SwitcHub-8mi SNMP Advanced Reference Guide BOOTP - When BOOTP is selected, the switch repeats requests at regular intervals, until it receives a valid reply. The requests will cease if a valid IP address is configured or the IP state is set to IP Disabled.
Fast SwitcHub-8mi SNMP Advanced Reference Guide Changing System Passwords Parameter Description Use the Password Configuration screen to display and modify passwords for the onboard configuration program. There are two user types, "Administrator" and " Normal User," the access privilege is Read/Write for Administrator and Read Only for Normal User. The default passwords are "Admin" and "Guest." Only the Administrator has write access for parameters governing the SNMP agent.
Fast SwitcHub-8mi SNMP Communication Mode - If you use auto-negotiation, be sure the attached device also supports this mode. If any device attached to the switch runs at full duplex, but does not support auto-negotiation, you will need to manually set the communication mode to full duplex. However, once set, the communication mode setting will remain unchanged, even if the link is broken (e.g., by unplugging the cable, or by a power reset).
Fast SwitcHub-8mi SNMP Parameter Default Description Switch Spanning Tree Algorithm Enabled Enable this parameter to participate in an STA compliant network. Priority 32,768 Device priority is used in selecting the root device, root port, and designated port. The device with the highest priority becomes the STA root device. However, if all devices have the same priority, the device with the lowest MAC address will then become the root device.
Fast SwitcHub-8mi SNMP Advanced Reference Guide Displaying Statistics and Configuration Data Displaying a Description of the Switch Use the System Information screen to display descriptive information about the switch, or for quick system identification.
Fast SwitcHub-8mi SNMP Advanced Reference Guide Displaying the Address Table Parameter Description The Address Table contains the MAC addresses associated with each port. (i.e., address and associated source port). To access information in the address tables, use the command options provided by the menu bar at the bottom of the screen. Use the "Display" command to select a port, "More" to scroll through a long listing, or "Search" to find a specific address.
Fast SwitcHub-8mi SNMP Parameter Description Max. Message Age The maximum time (in seconds) a device can wait without receiving a configuration message before attempting to reconfigure. Root The priority and MAC address of the device in the spanning tree that this switch has accepted as the root device. Advanced Reference Guide (continued) TFTP Download TFTP Server Address 192.72.24.17 Download Filename es3508.bin Root Cost The path cost from the root port on this switch to the root device.
Fast SwitcHub-8mi SNMP Parameter Description Display Diagnostics While Power-On Diagnostic indicators can be enabled/disabled during a hard reset. Reset Unit with Diagnostics Resets the unit and runs diagnostics. Clears all counters and restores configuration parameters from nonvolatile memory. The full process requires about 30 seconds. Reset Unit without Diagnostics Resets the unit without running diagnostics. Clears all counters and restores configuration parameters from nonvolatile memory.