FROST-FREE REFRIGERATORS Model Nos. FFAR12W / FFAR121SS INSTRUCTION MANUAL BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. Write Model and Serial Nos. (on lower left corner of inside cabinet) here: Model No.: _______________________ Serial No.: _______________________ Felix Storch, Inc. 770 Garrison Avenue Bronx, NY 10474 www.summitappliance.
TABLE OF CONTENTS Appliance Safety 3 Important Safeguards 3-4 Location of Parts 5 Installation Instructions 6-8 Before Using Your Appliance 6 Installation of Your Appliance 6 Electrical Connection 6-7 Extension Cord 7 Reversing the Door Swing of Your Appliance 7-8 Installing the Stainless Steel Handle 8 Operating Your Appliance 8-10 Control Panel 8-9 Sabbath Mode 9 Temperature Memory Function 10 Defrosting 10 Door Alarm 10 Door Lock 10 Care and Maintenance 11 Cleaning You
APPLIANCE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the Safety Alert Symbol. The symbol alerts you to potential hazards that can kill or injure you and others. All safety messages will follow the Safety Alert Symbol and either the word DANGER or WARNING.
- Avoid open flames and anything that creates a spark, - Disconnect from the power supply, - Air the room in which the appliance is located for several minutes and - Contact the Service Department for advice. • The more coolant there is in an appliance, the larger the room it should be installed in. In the event of a leakage, if the appliance is in a small room, there is the danger of combustible gases building up. For every ounce of coolant, at least 325 cubic feet of room space is required.
LOCATION OF PARTS LED Light Door Handle Shelves (4) Bottom Grille Security Lock Adjustable Legs Digital Control Panel Note: This appliance may be used for the storage of medicine and other medical products.
INSTALLATION INSTRUCTIONS BEFORE USING YOUR APPLIANCE • Remove the exterior and interior packing. • CAUTION: After unpacking you MUST allow this appliance to stand upright for at least 2 hours to allow the lubricant and refrigerant to drain back into the compressor and stabilize. Failure to do so may adversely affect performance and the lifetime of this unit. • Clean the interior surface with lukewarm water using a soft cloth. • Install the handle on the door, if it is not already attached. (See page 8.
overloading house wiring circuits that could cause a fire hazard from overheating. Never unplug the appliance by pulling on the power cord. Always grip the plug firmly and pull straight out from the receptacle. Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. When moving the appliance, be careful not to damage the power cord.
6. Screw the alternate left top hinge (7), included in the fittings, on the left hand side of cabinet. (Fig. 4) 7. Relocate the door to the designated position. Then screw the bottom hinge assembly on the left designated position and tighten it. Reinstall the plastic cover. (Fig. 5) 8. Recheck and adjust the door alignment by loosening the screws (5) and moving the door adapter (4). Tighten the screws (5) after the door is levelled. (Fig. 5) 9.
UP Used to increase (warm) the set temperature by 1°C/1ºF. DOWN Used to decrease (cool) the set temperature by 1°C/1ºF. Interior Light The interior light makes it easy to view your items. Touching the LIGHT symbol toggles between 2 modes of operation for the internal light: functional (default) mode and showcase mode. If you are in functional (default) mode, the light will turn on only when the door is open. If you are in showcase mode, the light will be on whether or not the door is open.
TEMPERATURE MEMORY FUNCTION In the event of a power interruption (power surge, breaker switch, etc.), the unit remembers the previous temperature settings, and when the power is recovered, the cabinet temperature will return to the same set temperature as before the power went off. DEFROSTING • The unit defrosts automatically in normal operating conditions. • The evaporator behind the rear wall of the unit defrosts automatically.
CARE AND MAINTENANCE CLEANING YOUR APPLIANCE • Turn off the power, unplug the appliance, and remove all items, including shelves. • Wash the inside surfaces with a solution of warm water and baking soda (about 2 tablespoons of baking soda to a quart of water). • Wash the shelves with a mild detergent solution. • Wring excess water out of the sponge or cloth when cleaning the area where the controls are located, or any electrical parts. • Wash the outside cabinet with warm water and mild liquid detergent.
TROUBLESHOOTING You can solve many common problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling the servicer. Troubleshooting Guide PROBLEM Appliance does not operate. POSSIBLE CAUSE • Appliance is not connected to a power supply. • The appliance is turned off. • Tripped circuit breaker or a blown fuse. • The temperature is not set correctly. • The ambient temperature could require a lower temperature setting.
• The appliance is not properly leveled. The door will not close properly. • The door was reversed and not properly re-installed. • The gasket is dirty. • The shelves are out of position. • Level the appliance with the adjustable feet. • Check the door hinge and reassemble correctly. • Clean the door gasket. • Check the shelves and refit correctly. • Call for service. Display “E0”, “E1”. “E2”, “E3”, “E4”, “E5” or “E7”. • “E0” indicates a communication error for 3-zone models.
NOTES 14
NOTES 15
LIMITED WARRANTY ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, warrantor will pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company. Outside the 48 states, all parts are warranted for one year from manufacturing defects.
