User's Manual

AT308 - USER MANUAL
12
4.2 BIPOD REMOVAL AND REFITTING (HARRIS BIPOD).
 To remove the bipod, loosen the retaining screw, pinch the locating tabs together and
remove the bipod.
 To fit the bipod, offer the locating tabs to the bipod adaptor stud. Once properly located
the bipod can be secured by tightening the retaining screw.
 The Harris bipod adaptor can be moved along the forend in the same way as the
accessory rails (see section 4.5), prior to fitting the bipod.
30.00
NOT RELEASED
PRELIMINARY
NOT CHECKED
.00 ± 0.1
15'
(3) REFERENCES TO STANDARDS & SPECS. IMPLY LATEST ISSUE.
mm
ACCURACY INTERNATIONAL
1
SH'T
.0 ± 0.25
UNIT ± 0.5
(WHERE NUMBER IN BOX IS APPLICABLE CHANGE)
WHERE A THREAD DEPTH IS QUOTED, IT IS MINIMUM FULL THREAD DEPTH.
1:10
E
AT, GENERAL ASSY (FOLDING)
NATO STOCK No:
ISSUE
AI-26677
F
G
H
J
K
CH'NGE
OTHERWISE
SCALE
DIM'N IN
vested in ACCURACY INTERNATIONAL LTD. No license is given by ACCURACY INTERNATIONAL LTD
L
STATED)
ORIGINAL
CHANGE:
C
(AND SIZE)
CERT'D
RESPONSIBLE AUTHORITY AND
TITLE
3rd Angle
D
FINISH
ESTIMATED
(UNLESS
(1) ALL BURRS & SHARP EDGES TO BE REMOVED.
LAST
3
0
(6) UNLESS OTHERWISE STATED, ALL TAPPED HOLE THREAD FORMS ARE TO BS 3643-6H.
The recipient acknowledges that the copyright & design right in this drawing belong to & remains
20
Projection
DRAWING NUMBER
CHECKED
DRAWN/DATE
A
DRAWING PROCEDURE TO DEF. STAN. 05-10 AND/OR BS 8888.
50
STATED)
MATERIAL
MASS
TOLS:
CORNERS OF BLIND HOLES, RECESSES & STEPS.
ARE INSPECTION DIMENSIONS
(4) ALL DIMENSIONS ARE FINISHED DIM'NS. i.e. AFTER APPLICATION OF SURFACE FINISH
The recipient shall maintain the confidentiality of the drawing.
g
100
ANG ±0
(2) A RADIUS OR CHAMFER OF 0.2 (MAX) IS PERMITTED IN THE
OF
1
DIMENSIONS DISPLAYED THUS
(5) DRAWING FEATURES MARKED THUS 3 INDICATE LATEST ISSUE MODIFICATION.
for the recipient to copy or make use of the information contained in thisdrawing.
DATE:
BY:
SPECIFICATION
SPECIFICATION
1 2 3 4 5 6 7 8 9 10
A
B
C
This drawing contains confidential information belonging to ACCURACY INTERNATIONAL LIMITED.
SURFACE ROUGHNESS
(UNLESS
OTHERWISE
N7
LOCATING TABS
BIPOD ADAPTOR
STUD
PINCH HERE
RETAINING SCREW
30.00
NOT RELEASED
PRELIMINARY
NOT CHECKED
STATED)
The recipient acknowledges that the copyright & design right in this drawing belong to & remains
(AND SIZE)
CERT'D
CHECKED
DRAWN/DATE
FINISH
MATERIAL
MASS
ESTIMATED
vested in ACCURACY INTERNATIONAL LTD. No license is given by ACCURACY INTERNATIONAL LTD
CH'NGE
STATED)
OTHERWISE
SCALE
DIM'N IN
TITLE
ORIGINAL
CHANGE:
C
RESPONSIBLE AUTHORITY AND
DRAWING NUMBER
LAST
3
0
20 50 100
(UNLESS
A
15'
.00 ± 0.1
.0 ± 0.25
UNIT ± 0.5
Projection
3rd Angle
ANG ±0
TOLS:
L
(3) REFERENCES TO STANDARDS & SPECS. IMPLY LATEST ISSUE.
mm
ACCURACY INTERNATIONAL
1
CORNERS OF BLIND HOLES, RECESSES & STEPS.
(2) A RADIUS OR CHAMFER OF 0.2 (MAX) IS PERMITTED IN THE
OF 1
ARE INSPECTION DIMENSIONS
DIMENSIONS DISPLAYED THUS
SH'T
(1) ALL BURRS & SHARP EDGES TO BE REMOVED.
DRAWING PROCEDURE TO DEF. STAN. 05-10 AND/OR BS 8888.
WHERE A THREAD DEPTH IS QUOTED, IT IS MINIMUM FULL THREAD DEPTH.
(6) UNLESS OTHERWISE STATED, ALL TAPPED HOLE THREAD FORMS ARE TO BS 3643-6H.
(WHERE NUMBER IN BOX IS APPLICABLE CHANGE)
(5) DRAWING FEATURES MARKED THUS 3 INDICATE LATEST ISSUE MODIFICATION.
(4) ALL DIMENSIONS ARE FINISHED DIM'NS. i.e. AFTER APPLICATION OF SURFACE FINISH
The recipient shall maintain the confidentiality of the drawing.
g
1:10
AT, GENERAL ASSY (FOLDING)
NATO STOCK No:
ISSUE
AI-26677
for the recipient to copy or make use of the information contained in thisdrawing.
DATE:
BY:
SPECIFICATION
SPECIFICATION
1 2 3 4 5 6 7 8 9 10
A
B
C
D
E
F
G
H
J
K
This drawing contains confidential information belonging to ACCURACY INTERNATIONAL LIMITED.
SURFACE ROUGHNESS
(UNLESS
OTHERWISE
N7
HARRIS BIPOD
ADAPTOR