Specifications

ManualsBrandsAccurate Technology ManualsBusiness equipmentDigi-Stop

Contents

1. Introduction………………………………………………………………......2

1.1 Product Introduction………………………………………………………2

1.2 Indication of Use……………………………………………………………2

1.3 Safety………………………………………………………………….….....2

1.4 Product Functions and Features……………………………………….….3

1.5 Technical Specifications…………………………………………….……...3

1.6 Product Description………………………………………………….…….4

1.7 Symbols and Labels………………………………………………….……..4

1.8 Product Components………………………………………………….……6

1.9 Battery Charge……………………………………………………….…….7

1.10 Pump Installation…………………………………………………….…….7

2. Syringe Pump Operation.…………………………………………….……...8

2.1 Basic Operations Steps……………………………………………………..8

2.2 Bolus Function…………………………………………………………..….11

3. Configuration……………………………………………………………...….12

3.1 Enable & Disable NEAR Alarm .………………………………………….12

3.2 Syringe Configuration Change…..…………………………………….…..12

3.3 Occlusion Sensibility Adjust…..……………………………………………15

4. Cleaning, Storage, Transport and Maintenance…………………………….15

4.1 Cleaning……………………………………………………………………...15

4.2 Transport and Storage………………………………………………………15

4.3 Preventive Inspection………………………………………………………..16

4.4 Environmental Protection…………………………………………………..16

5. Alarms………………………………………………………………….………17

5.1 Alarms and Actions…………………………………………………….……17

5.2 Troubleshooting……………………………………………………….…..…18

5.3 Service………………………………………………………………………..19

Warranty Terms…………………………………………………………….…..20

Rev 2

Summary of content (20 pages)

PAGE 1
Contents 1. Introduction………………………………………………………………......2 1.1 Product Introduction………………………………………………………2 1.2 Indication of Use……………………………………………………………2 1.3 Safety………………………………………………………………….….....2 1.4 Product Functions and Features……………………………………….….3 1.5 Technical Specifications…………………………………………….……...3 1.6 Product Description………………………………………………….…….4 1.7 Symbols and Labels………………………………………………….……..4 1.8 Product Components………………………………………………….……6 1.9 Battery Charge……………………………………………………….…….7 1.
PAGE 2
1. Introduction 1.1 Product Introduction The DigiPump™ SR7x syringe pump is a combination of microelectronic technology and innovation in nursing medicine. It can control the infusion rate and total volume precisely and continuously over long hours on a large scale. The DigiPump™ SR7x syringe pump is a hi-tech equipment which can be used in all areas of modern nursing. The patient’s infusion situation and alarm information (e.g. infusion completion, occlusion) can all be seen at the central station.
PAGE 3
7. Warning: when using Non standard syringe or setting syringe parameters incorrect, the accuracy may not be maintained and the discrepancy may reach 5% or above. When changing Syringe types and syringe calibration settings, it is the user responsibility to ensure that required accuracy is obtained. 8. Warning: the used syringe shall not be installed on other infusion devices to avoid potential risk. 9. Warning: Keep cell phone or other high frequency power devices away from the syringe pump within 2’ (0.
PAGE 4
syringe abnormal, control abnormal, no AC power alarm 288mm×130mm×122m（11.3”×5.1”×4.8”）＜2.4Kg (5.3lb) Type IIB ABS plastic Environment temperature 5℃~40℃, air pressure 80kPa ~106kPa，relative humidity 20 ~ 90% Environment temperature -15℃~50℃, air pressure 86kPa~106kPa，relative humidity 20 ~ 90% 10 ml、20 ml、50 ml syringes continuous Maximum enclosure size Maximum weight Classification Enclosure material Operating conditions Storage conditions Applicable syringes Operating mode 1.
PAGE 5
2. Label Mark Mark Description Production batch No. Serial Number Caution! Consult user manual Class II equipment Type BF applied part Protection against vertically falling water drops IP21 It indicates that the equipment should be sent to the special agencies according to local regulation for disposal after its useful life. Date of production Manufacturer CE mark ～ Alternating current European Representative 3. Standard configuration in the packaging box 1. Syringe pump one pc 2.
PAGE 6
1.8 Product Components No. 1 2 Description Battery capacity indicator light AC power indicator light 3 Infusion indicator light 4 LCD display 5 Accumulated Volume light 6 Infusion rate light 7 Bed number light 8 NEAR alarm indicator light 9 OCCL alarm indicator light 10 OVER alarm indicator light 11 SELECT key 12 POWER key 13 CLEAR key 14 15 16 STOP key START key BOLUS key Function The 3 lights indicate the battery capacity level.
PAGE 7
17 Adjust & Confirm Knob 18 Clutch button 19 Piston 50 ml syringe indicator light 20 21 22 23 24 20 ml syringe indicator light 10 ml syringe indicator light Syringe Holder User-friendly instructions pump infuses at maximum rate for the syringe. Rotating the knob adjust value. Pressing the knob confirm and save the adjusted value. Keep pressing the button to move the piston freely. When unfastening the button, the clutch will gear, and can only be moved by the engine.
PAGE 8
2. Syringe Pump Operation 2.1 Basic Operation Steps Step 1 Power connection Insert the power cord into the power supply (AC 100 V～240V, 50/60 Hz). Connect the power cord as shown. Step 2 Turn the Power On Keep pressing Press POWER key for 3 – 5 seconds and then release it. The Digipump SR7x start a self-test, all indicator lights and enters in operation mode. Note: When the orange AC light is on, the syringe pump is using AC power and the battery is being charged automatically.
PAGE 9
(3) Before the installation, manually remove all the air inside the syringe and then place the syringe on the mounting grooves. (4) Return the Syringe Holder to original position compressing and holding the syringe in place. When the Syringe Holder compresses the syringe, the syringe size indicator is displayed in the screen.
PAGE 10
Note: The accumulated volume can be viewed during the infusion pressing the SELECT key, but to clear the accumulated volume the syringe pump need to be in STOP mode. Note: accumulated volume can be cleared only in STOP condition. Step 7 Start infusion (1) After all values are set and the syringe is properly installed, press START key to start the infusion, the infusion lights will flash from right to left. The piston shall drive the syringe from right to left slowly as the infusion begins.
PAGE 11
As shown in the figure bellow, when the infusion is completed, the OVER indicator light is ON, accompanied with an audible alarm signal to alert the user. Press the STOP key and the syringe pump stops operation. Note: The OVER alarm can be silenced by pressing the adjusting knob. The OVER audible alarm will sound again in 2 minutes. Step 9 Turn off the power Press the POWER key for 3-5 seconds and then release it, the machine power is turned-off. 2.
PAGE 12
3. Configuration 3.1 Enable and Disable ‘NEAR’ Alarm Function (1) With the syringe pump off, press and hold the START + CLEAR + POWER keys simultaneously. The syringe pump is turned-on and a configuration mode sound indicates the syringe pump enters configuration mode. Release all the keys together. (2) The syringe pump enters into the configuration mode to lock and unlock the NEAR alarm. The NEAR alarm light is turned on and the screen display a value.
PAGE 13
Step 1 Measure the syringe length Measure the new syringe length in millimeters (mm). Step 2 Install the syringe Turn off the syringe pump. Install the new syringe on the pump. Push the syringe piston to compressing the syringe all the way to the syringe’s end. Warning: The correct installation of the syringe and the piston is essential when changing the calibration settings or error may occur.
PAGE 14
2)- 20ml syringe’s parameter setting: With the syringe pump OFF, press and hold the BOLUS + POWER keys simultaneously. The syringe pump is turned-on and a configuration mode sound indicates the syringe pump enters configuration mode. Release all the keys together. The 20ml indicator light will be ON and the 20ml current parameter value is displayed. Turn the adjusting knob to change the value to the one measured in step 1, then press the knob to save the new value.
PAGE 15
3.3 Occlusion Sensibility Adjust The occlusion pressure is sensibility can be adjusted by the user. The value range goes from 12 to 20. The sensibility is set in the factory to 13. The smaller the value is, the more sensitive the occlusion alarm is. The actual pressure value depends on the syringes size and conditions in the range from 10 to 25PSI. To change the occlusion pressure sensibility value, with the syringe pump OFF, press and hold the START + POWER keys simultaneously.
PAGE 16
4.3 Preventive Inspection 1. Flow Rate accuracy check. Use one volume calibrated recipient to verify Flow Rate and Volume accuracy every time new syringes are being used or every six months. 2．Battery Inspection Batteries have limited life time. Replace the batteries when they are not holding charge. If replacing batteries are required, please contact Digicare. Model: Lithium Polymer battery （7.4V，1650mAh）.
PAGE 17
5. Alarms 5.1 Alarms and Actions Reason Solution The syringe is almost empty and close to end of infusion 1.press the knob to cancel the alarm(the alarm will ring again after two minutes) 2. Press STOP key to stop the syringe pump and cancel the alarm. The syringe is empty and infusion is finished 1. Press the knob to cancel the alarm(the alarm will ring again after two minutes) 2. Press STOP key to stop the syringe pump and cancel the alarm. Occlusion alarm 1.
PAGE 18
1．The syringe is disengaged or not properly installed. 2．The syringe’s parameter is wrongly set. 3. Something is wrong with the syringe sensor Syringe Disengaged 1． The syringe’s parameter is wrongly set 2. the syringe pump’s motor can’t run properly Control Abnormal 5.2 No.1：Install the syringe again No.2：Refer to item 3.2 Syringe Configuration Change No.3：Contact Digicare Technical Support No.1：Refer to 3.2 Syringe Configuration Change No.
PAGE 19
5.3 Service Attention: 1. If there is any untreatable fault or question, please stop using the Digipump SR7x Syringe Pump and contact Digicare for Technical Support and Service. 2. Unauthorized person has no right to repair this product; otherwise Digicare will take no responsibility.
PAGE 20
WARRANTY TERMS & CONDITIONS DIGICARE BIOMEDICAL TECHNOLOGY, INC. covers all of their infusion pumps with a 1 year warranty: Infusion Pump DigiPump SR7x: 1 year parts and labor Accessories: 90 days on accessories only DIGICARE BIOMEDICAL TECHNOLOGY, INC. will provide the necessary parts and labor to maintain the monitor (s) listed on the Warranty Certificate in a usable condition during the covered period. DIGICARE BIOMEDICAL TECHNOLOGY, INC.