User manual

DISPLAY MODES
• STEP: STEP mode shows
your step count since last reset,
up to 1,000,000 steps.
•
◯: ACTIVITY TIMER
MODE shows total activity
time in minutes and seconds
since last reset. The timer runs
automatically whenever steps
are being recorded.
Adjusting your Pedometer’s
Measurement Sensitivity AE1700
pedometers are highly accurate step
counters. However, some walkers may
find that their step counts tend to be
a bit too high, or too low. All AE1700
models come with a sensitivity adjust-
ment, to help account for individual
differences. The adjustment switch has
three positions: “+,” “-,” and center.
The adjustment switch is located on the
bottom of the pedometer, on the right-
hand side when looking from the front.
Adjustment Procedure: Take 100 steps,
then check STEPS display to see how
many steps were actually counted.
Repeat once to make sure results are
about the same. If the pedometer counts
fewer steps than you actually walked,
slide the sensitivity adjustment towards
the “+” icon. This will increase recorded
steps by about 10%. If the pedometer
counts more steps than you actually
walked, slide the sensitivity adjustment
towards the “-” icon. This will decrease
recorded steps by about 10%.
WEARING YOUR PEDOMETER
While gently holding the belt clip open,
slide the pedometer onto your belt or the
top edge of your pants or skirt. It should
fit snugly and level, above one knee.
Note: The pedometer should be as
vertical as possible. Walkers with larger
stomachs may find it helpful to wear the
pedometer farther back on the body,
toward one hip. The cover must be closed
for the pedometer to work. To avoid
losing or dropping your pedometer, use
the included leash and clip to fasten the
pedometer securely to your clothing.
Attaching the Leash: Attach the
pedometer to the leash by looping the
leash through the pedometer leash slot.
Next, loop the leash through the metal
clip. Finally, clasp the waistband of your
clothing with the metal clip. You can also
use a safety pin to fasten the leash to
your clothing, loop the leash through your
belt or belt loop, or use a badge holder.
ACCUSPLIT AE1720WPR Series Pedometer
INSTRUCTIONS
ACCUSPLIT, Inc. • 2290M Ringwood Ave. • San Jose, CA 95131
800-965-2008 • 925-226-0888 • FAX [phone] • www.ACCUSPLIT.com • [e-mail]
E Rig! W Mr! Lv W!
 ACCUSPLIT Lftl
Congratulations on taking the first step to wellness
with your purchase of an ACCUSPLIT pedometer.
It’s easy to set up your new pedometer.
Just follow the steps below, and start walking!
Red:
MODE
9789
ACCUSPLIT EAGLE
�
STEP
▶
White:
RESET
970-071
First, loop the
pedometer leash slot
Next, loop the metal
clip, then clasp clothing
Or, loop a
badge holder,
then put into pocket
(Badge holder
not included)
Or, loop a belt or belt loop
VIEWING YOUR RESULTS
Once you put on your pedometer with the
cover closed, it will automatically begin
to record your steps, and activity time.
Repeatedly press the red MODE button to
cycle through the pedometer modes:
STEP → ACTIVITY TIMER → STEP
RESETTING YOUR PEDOMETER
Most people prefer to reset step counts
daily. To reset: press and hold the white
RESET button for at least 2 seconds.
REPLACING THE BATTERY
When the display starts to dim or goes
blank, it is time to replace the battery.
Your pedometer uses one Type L1142
(LR43) 1.5 volt silver oxide battery.
To replace:
1. Insert a coin into the slot on the front
of the case, and twist counterclock-
wise to loosen the battery door.
2. Remove battery door and take out the
old battery. Replace it with a new
battery. The battery’s positive (+)
terminal should be FACE UP while you
put it into the pedometer.
3. Put the battery door back on and twist
the coin clockwise to tighten.
You are also helping to support the cause of breast cancer
awareness and research. A portion of the proceeds from your
purchase will be donated to a breast cancer initiative.