1N Wireless Broadband Router 1
11N Wireless Broadband Router Copyright Statement is the registered trademark of Shenzhen Tenda Technology Co., Ltd. All the products and product names mentioned registered herein trademarks of are their the trademarks respective or holders. Copyright of the whole product as integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd. Without the permission of Shenzhen Tenda Technology Co.
11N Wireless Broadband Router Contents CHAPTER 1 INTRODUCTION .......................................... 1 1.1 PRODUCT FEATURES .......................... 2 1.2 PACKAGE CONTENTS ......................... 4 1.3 LED INDICATOR AND PORT DESCRIPTION ....... 4 CHAPTER 2 PRODUCT INSTALLATION........................ 7 2.1 HARDWARE INSTALLATION .................... 7 2.2 NETWORK APPLICATION PLAN ................. 9 CHAPTER 3 HOW TO LOGIN TO THE ROUTER....... 10 3.1 HOW TO SET THE NETWORK CONFIGURATIONS .. 10 3.
11N Wireless Broadband Router 6.6 WIRELESS ACCESS CONTROL ................. 37 6.7 CONNECTION STATUS ....................... 38 CHAPTER 7 DHCP SERVER............................................ 39 7.1 DHCP SETTINGS ........................... 39 7.2 DHCP LIST AND BINDING ................... 40 CHAPTER 8 VIRTUAL SERVER ..................................... 41 8.1 PORT RANGE FORWARDING .................. 41 8.2 DMZ SETTINGS ............................ 43 8.3 UPNP SETTINGS ...........................
11N Wireless Broadband Router 12.5 UPGRADE FIRMWARE....................... 12.6 REBOOT THE ROUTER ...................... 12.7 PASSWORD CHANGE ....................... 12.8 SYSLOG ................................. 12.9 LOGOUT ................................. 62 62 63 64 65 APPENDIX 1 GLOSSARY................................................. 66 APPENDIX 2 QUESTIONS AND ANSWERS ..............
11N Wireless Broadband Router Chapter 1 Introduction Thank you for purchasing Tenda W311R/W311R+ 11N Wireless Broadband Router! W311R/W311R+ utilizes the latest IEEE802.11n standard with its wireless transmitting distance up to 6 times and transmitting rate 3 times than wireless G-products. It complies perfectly backwards with 802.11b/g standards and includes Router, Wireless AP, 4-port switch, and firewall in one. WMM enables you a comfortable journey in audio and video streaming and on-line games.
11N Wireless Broadband Router 1.1 Product Features z Includes router, wireless access point, four-port switch and firewall in one z “Setup Wizard” enables you to connect Internet without entering administration interface z Complies with the latest IEEE802.11n standard and IEEE802.11 b/g standards z Increases 6 times coverage distance than 802.
11N Wireless Broadband Router z Supports remote Web management and simple Web upgrading method z Supports wireless Roaming technology for high-efficient wireless connections z Supports SSID stealth mode and access control based over MAC address (up to 30 entries) z Supports Auto MDI/MDIX z Provides syslog to record the status of the router z Supports auto negotiation/manual mode for 802.11b/802.11g z Supports UPnP and DDNS z Supports Firefox1.0, IE5.
11N Wireless Broadband Router 1.2 Package Contents Please unpack the box and check the following items: ¾ One W311R/W311R+ Wireless Broadband Router ¾ One Quick Installation Guide ¾ One Power Adapter ¾ One CD-ROM ¾ One External Antenna(only for W311R+) If any of listed items are missing or damaged, please contact the Tenda reseller from whom you purchased for replacement immediately. 1.
11N Wireless Broadband Router ¾ SYS When turns green, blinking indicates the system runs well. ¾ WPS When blinking, it indicates the device is negotiating with client in WPS mode. ¾ WLAN Wireless signal LED indicator. When turns green, blinking indicates the wireless function is enabled. ¾ LAN (4,3,2,1) Wired local network LED indicator. Always ON indicates it is connected with Ethernet device; blinking indicates the device is transmitting and/or receiving data. ¾ WAN Wide area network indicator.
N Wireless Broadband Router Back Panel Show: Rear Panel :( From L to R) ¾ POWER The jack is for power adapter connection. Please use the included 9V DC power adapter. ¾ WAN A 100Mbps Ethernet port can be connected with MODEM, Switch, Router and other Ethernet device for Internet connecting to DSL MODEM, Cable MODEM and ISP. ¾ LAN (1, 2, 3, 4) 4 10/100Mbps Ethernet ports can be connected with Ethernet switch, Ethernet router and NIC card. ¾ RESET The system reset button.
11N Wireless Broadband Router Chapter 2 Product Installation 2.1 Hardware Installation After you unpack the box, please follow the steps below to connect. For better wireless performance, please put the device in the middle of wireless coverage area. 1. Please use the included power adapter to power on the Router. IMPORTANT: Use of a different power adapter could cause damage and void the warranty for this product. 2.
11N Wireless Broadband Router 3. Please connect your broadband line provided by your ISP to the WAN port. 4. Insert the included CD-ROM into the CD-ROM drive, double click the “Setup” icon and follow the instructions to complete the installation. Or you can enter the Router’s Web page to configure it. (More details please refer to Chapter 3.
11N Wireless Broadband Router 2.2 Network Application Plan Usually wireless LAN Network is deployed in a planned environment where each access point is located in a steady place with certain wireless coverage area for communication service. Generally speaking, it is in the center of the area to reduce “dead spot”.
11N Wireless Broadband Router Chapter 3 How to Login to the Router The chapter mainly presents how to enter the Router’s Web page. After you have finished the hardware installation, the following steps will assist you to set the network configurations for you computer. 3.1 How to Set the Network Configurations 1. On your computer desktop right click “My Network Places” and select “Properties”.
11N Wireless Broadband Router 2. Right click “Local Area Network Connection” and select “Properties”. 3. Select “Internet Protocol “Properties”.
11N Wireless Broadband Router 4. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”. Click “OK” to save the configurations. Or select “Use the following IP address” and enter the IP address, Subnet mask, Default gateway as follows: IP Address: 192.168.0.XXX: (XXX is a number from 2~254) Subnet Mask: 255.255.255.0 Gateway: 192.168.0.1 Certainly you need to input the DNS server address provided by your ISP.
11N Wireless Broadband Router 3.2 Login to the Router 1. To access the Router’s Web-based interface, launch a web browser such as Internet Explorer or Firefox and enter the Router’s default http://192.168.0.1. Press “Enter”.
11N Wireless Broadband Router 2. Input the “admin” in both User Name and Password. Click “OK”. 3. If you enter the correct user name and password, the screen will be the next one.
11N Wireless Broadband Router Chapter 4 Quick Setup Guide This chapter deals with how to access the Internet quickly. Please follow this guide to connect your Router to the Internet. 4.1 Setup Wizard Here is the “Welcome to Setup Wizard” for configuring your Router quickly. Click “Next”. In this screen, select one mode of your Internet connection you use. If you are not clear, press the “Detect” button or contact your Internet Service Provider, and click “Next”.
11N Wireless Broadband Router ADSL Virtual Dial-up (Via PPPoE) Enter the Account and Password provided by your ISP, and click “Next”. For example: Dynamic IP (Via DHCP) If your connection mode is Dynamic IP, it means your IP address keeps changing every time you connect. You do not need to enter the information like other modes. Click “Next” and “Save” to finish the settings.
11N Wireless Broadband Router Static IP In this screen, fill the network address information from your ISP in the IP Address, Subnet Mask, Gateway and Primary DNS server fields and click “Next”. For example: ISP provides the following TCP/IP parameters as follows: IP Address: 192.168.1.2 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.1 Primary DNS Server: 192.168.1.2 Alternate DNS Server: 202.96.134.
11N Wireless Broadband Router Click “Save” to complete the setup wizard. The Router will record the settings you made. To activate the settings, it is recommended to select “Reboot the Router” from “System Tool” of the left menu. It is rebooting now, please wait for a few minutes and DO NOT power off it. Click the “System Status” in the left menu of the Web-based Utility to find out the current network and system information.
11N Wireless Broadband Router Chapter 5 Advanced Settings 5.1 LAN Settings LAN Settings are for the basic TCP/IP parameters of LAN ports. ¾ MAC Address: The Router’s physical MAC address as seen on your local network, which is unchangeable. ¾ IP Address: The Router’s LAN IP addresses (not your PC’s IP address). 192.168.0.1 is the default value. ¾ Subnet Mask: It’s shown the Router’s subnet mask for measurement of the network size. 255.255.255.0 is the default value.
11N Wireless Broadband Router 5.2 WAN Settings After you have selected the ISP connection type in “Setup Wizard” and you want to modify the related settings, here you can modify and configure the settings in details. Virtual Dial-up (PPPoE) ¾ Connection Mode: Show your current connection mode. ¾ Account: Enter them provided by your ISP. ¾ Password: Enter them provided by your ISP. ¾ MTU: Maximum Transmission Unit. It is the size of largest datagram that can be sent over a network.
11N Wireless Broadband Router The default value is 1492. Do NOT modify it unless necessary. But if when some specific website or web application software can not be open or enabled, have a try to change the MTU value as 1450, 1400, etc. ¾ Service Name: characteristics It that is defined are applied as to a a set of PPPoE connection. Enter it if provided. Do NOT modify it unless necessary. ¾ AC Name: Enter it if provided. Do NOT modify it unless necessary.
11N Wireless Broadband Router Static IP If your connection mode, static IP is chosen, you can modify the following addressing information. ¾ IP Address: Here enter the WAN IP address provided by your ISP. ¾ Subnet Mask: Enter the WAN Subnet Mask here. ¾ Gateway: Enter the WAN Gateway here. ¾ Primary DNS Server: Enter the Primary DNS server provided by your ISP. ¾ Secondary DNS Server: Enter the secondary DNS.
11N Wireless Broadband Router 5.3 MAC Address Clone This page is for the Router’s MAC address to WAN. Some ISPs require end-user's MAC address to access their network. This feature copies the MAC address of your network device to the Router. ¾ MAC Address: The MAC address to be registered with your Internet service provider. ¾ Clone MAC Address: Register your PC's MAC address. ¾ Restore Default MAC Address: Restore to the default hardware MAC address.
11N Wireless Broadband Router 5.4 DNS Settings DNS is short for Domain Name System (or Service), an Internet service that translate domain names into IP addresses which are provided by your Internet Service Provider. Please consult your Internet Service Provider for details if you do not have them. ¾ DNS: Click the checkbox to enable the DNS server. The Router’s DHCP sever will answer the client’s requests and distribute DNS address.
11N Wireless Broadband Router Chapter 6 Wireless Settings 6.1 Basic Settings ¾ Enable Wireless: Check to enable the Router’s wireless features; uncheck to disable it. You can also press the WLAN/WPS button to turn on/off the wireless function. ¾ Network Mode: Select one mode from the following. The default is 11b/g/n mode.
11N Wireless Broadband Router with the device in 11b mode at the maximum speed of 11Mbps. 11g mode: Allow the 11g/11n-compliant client device to connect with the AP at the maximum speed of 54Mbps. 11b/g mode: Allow the 11b/g-compliant client device to connect with the AP with auto-negotiation speed, and 11n wireless client to connect the device with 11g speed. 11b/g/n mode: Allow 11b/g/n-compliant client device to connect with the AP with auto-negotiation speed.
11N Wireless Broadband Router ¾ Channel Bandwidth:Select the channel bandwidth to improve the wireless performance. When the network has 11b/g and 11n clients, you can select the 40M; when it is an 11n network, select 20/40M to improve its throughput. 6.2 Wireless Security Settings It is used to configure the AP network’s security setting. Here presents the common six (ten in all) encryption methods, including Mixed WEP, WPA-personal, WPA-enterprise, WPA2-personal, WPA2- enterprise, etc. 6.2.
11N Wireless Broadband Router ¾ Select SSID:Select the SSID (main SSID or minor SSID) to configure security setting from the drop-down menu. ¾ Security Mode:From the drop-down menu select the corresponding security encryption modes. ¾ WEP Key1~4:Set the WEP key with the format of ASCII and Hex. You can enter ASCII code (5 or 13 ASCII characters. Illegal character as “/” is not allowed.) Or 10/26 hex characters. ¾ Default Key:Select one key from the configured keys as the current available one.
11N Wireless Broadband Router 6.2.2 WPA-Personal WPA (Wi-Fi Protected Access), a Wi-Fi standard, is a more recent wireless encryption scheme, designed to improve the security features of WEP. It applies more powerful encryption types (such as TKIP [Temporal Key Integrity Protocol] or AES [Advanced Encryption Standard]) and can change the keys dynamically on every authorized wireless device. ¾ WPA Algorithms:Provides TKIP [Temporal Key Integrity Protocol] or AES [Advanced Encryption Standard].
11N Wireless Broadband Router 6.2.3 WPA2- Personal WPA2 (Wi-Fi Protected Access version 2) provides higher security than WEP (Wireless Equivalent Privacy) and WPA (Wi-Fi Protected Access). ¾ WPA Algorithms:Provides TKIP [Temporal Key Integrity Protocol] or AES [Advanced Encryption Standard]. The default is TKIP mode. ¾ Pass Phrase:Enter the encrypted characters with 8-63 ASCII characters. ¾ Key Renewal Interval:Set the key’s renewal period.
11N Wireless Broadband Router 6.3 Advanced Settings This section is to configure the advanced wireless setting of the Router, including the Radio Preamble, 802.11g/n Rate, Fragmentation Threshold, RTS Threshold, etc. ¾ BG protection Mode: Auto by default. It is for 11b/g wireless client to connect 11n wireless network smoothly in a complicated wireless area. ¾ Basic Data Rates: For different requirement, you can select one of the suitable Basic Data Rates. Here, default value is (1-2-5.5.-11Mbps…).
11N Wireless Broadband Router threshold defines the maximum transmission packet size in bytes. The packet will be fragmented if the arrival is bigger than the threshold setting. The default size is 2346 bytes. It is recommended not to modify this value. ¾ RTS Threshold: RTS stands for “Request to Send”. This parameter controls what size data packet the frequency protocol issues to RTS packet. The default value of the attribute is 2346. It is recommended not to modify this value in SOHO environment.
11N Wireless Broadband Router 6.4 WPS Settings WPS (Wi-Fi Protected Setting) can be easy and quick to establish the connection between the wireless network clients and the device through encrypted contents. The users only enter PIN code or press WLAN/WPA button on the panel to configure it without selecting encryption method and secret keys by manual. In the “Wireless settings” menu, click “WPS settings” to enter the next screen. ¾ WPS settings: To enable or disable WPS function.
11N Wireless Broadband Router one second (Press the button for about one second and WPS indicator will be blinking for 2 minutes, which means the WPS is enabled. During the blinking time, you can enable another device to implement the WPS/PBC negotiation between them. Two minutes later, the WPS indicator will be off, which means the WPS connection is completed. If more clients are added, repeat the above steps. At present, the WPS supports up to 32 clients access.
11N Wireless Broadband Router ¾ WPS Encrypt Type: The encryption type used by WPS, generally AES/TKIP. ¾ WPS key: The effective key generated by AP automatically. ¾ AP PIN(KEY): The PIN code used by default. ¾ Reset OOB: When this button is pressed, the WPS client will be idle state, and WPS indicator will be turned off. AP will not respond the WPS client’s requests and the set the security mode as WPA mode. 6.
11N Wireless Broadband Router to establish the connection. Bridge: You can wirelessly connect two or more wired networks via this mode. In this mode, you need to add the Wireless MAC address of the connecting device into the Router's AP MAC address table or select one from the scanning table. Repeater Mode:In this mode, add the opposing MAC address into each own AP MAC address table by manual or scanner to enlarge and extend the wireless radio. Encrypt Type: Select one from WEP, TKIP, AES for security here.
11N Wireless Broadband Router 6.6 Wireless Access Control To secure your wireless LAN, the wireless access control is actually based on the MAC address management to allow or block the specific clients to access the wireless network. Select “Wireless Setting->Access Control” to display the following screen: ¾ MAC Address Filter: Enable/disable MAC address filter.
11N Wireless Broadband Router 6.7 Connection Status This page shows wireless client’s connection status, including MAC address, Channel bandwidth, etc. Select “Wireless Setting->connection status” to enter the following screen: ¾ MAC Address: Shows current MAC addresses of the hosts connecting to the Router. ¾ Bandwidth: Shows current bandwidth of the hosts (wireless client).
11N Wireless Broadband Router Chapter 7 DHCP Server 7.1 DHCP Settings DHCP (Dynamic Host Control Protocol) is to assign an IP address to the computers on the LAN/private network. When you enable the DHCP Server, the DHCP Server will allocate automatically an unused IP address from the IP address pool to the requesting computer in premise of activating “Obtain an IP Address Automatically”. So specifying the starting and ending address of the IP Address pool is needed.
11N Wireless Broadband Router 7.2 DHCP List and Binding The Static IP assignment is to add a specifically static IP address to the assigned MAC address. You can view the related information in the DHCP server list. ¾ IP Address: Enter the IP address which needs to be bound. ¾ MAC Address: Enter the MAC address of the computer you want to assign the above IP address. Click “Add” to add the entry in the list. ¾ Hostname: The name of the computer which is added a new IP address.
11N Wireless Broadband Router Chapter 8 Virtual Server 8.1 Port Range Forwarding This section deals with the port range forwarding mainly. The Port Range Forwarding allows you to set up a range of public services such as web servers, ftp, e-mail and other specialized Internet applications to an assigned IP address on your LAN. ¾ Start/End Port: Enter the start/end port number which ranges the External ports used to set the server or Internet applications.
11N Wireless Broadband Router ¾ IP Address: Enter the IP address of the PC where you want to set the applications. ¾ Protocol: Select the protocol (TCP/UDP/Both) for the application. ¾ Delete/Enable: Click to check it for corresponding operation. ¾ Well-Known Service Port: Select the well-known services as DNS, FTP from the drop-down menu to add to the configured one above. ¾ Add: Add the selected well-known port to the policy ID. For example: The server at IP address of 192.168.0.
11N Wireless Broadband Router 8.2 DMZ Settings The DMZ function is to allow one computer in LAN to be exposed to the Internet for a special-purpose service as Internet gaming or videoconferencing. ¾ DMZ Host IP Address: The IP address of the computer you want to expose. ¾ Enable: Click the checkbox to enable the DMZ host. For example: Set the computer at IP address of 192.168.0.10 as DMZ host to connect another host in the Internet for intercommunication.
11N Wireless Broadband Router software that supports UPnP. With the UPnP function, host in LAN can request the router to process some special port switching so as to enable host outside to visit the resources in the internal host. ¾ Enable UPnP: Click the checkbox to enable the UPnP.
11N Wireless Broadband Router Chapter 9 Traffic Control 9.1 Traffic Control Traffic control is used to limit communication speed in the LAN and WAN. Up to 20 entries can be supported with the capability for at most 254 PCs' speed control, including for IP address range configuration. ¾ Enable Traffic Control: To enable or disable the internal IP bandwidth control. The default is disabled. ¾ Interface: To limit the uploading and downloading bandwidth in WAN port.
11N Wireless Broadband Router as HTTP service. ¾ IP Starting Address: The first IP address for traffic control. ¾ IP Ending Address: The last IP address for traffic control. ¾ Uploading/Downloading: To specify the traffic heading way for the selected IP addresses: uploading or downloading. ¾ Bandwidth: To specify the uploading/downloading Min. /Max. Traffic speed (KB/s), which can not exceed the WAN speed. ¾ Apply: To enable the current editing rule. If not, the rule will be disabled.
11N Wireless Broadband Router Chapter 10 Security Settings 10.1 Client Filter Settings To benefit your further management to the computers in the LAN, you can control some ports access to Internet by data packet filter function. ¾ Client Filter: Check to enable client filter. ¾ Access Policy: Select one number from the drop-down menu. ¾ Enable: Check to enable the access policy. ¾ Clear the Policy: Click “Clear” button to clear all settings for the policy.
11N Wireless Broadband Router ¾ Filter Mode: Click one radio button to enable or disable to access the Internet. ¾ Policy Name: Enter a name for the access policy selected. ¾ IP Start/End: Enter the starting/ending IP address. ¾ Port No: Enter the port range based over the protocol for access policy. ¾ Protocol: Select one protocol (TCP/UDP/Both) from the drop-down menu. ¾ Times: Select the time range of client filter. ¾ Date: Select the day(s) to run the access policy.
11N Wireless Broadband Router 10.2 URL Filter Settings In order to control the computer to have access to websites, you can use URL filtering to allow the computer to have access to certain websites at fixed time and forbids it having access to certain websites at fixed time. ¾ URL Filter: Check to enable URL filter. ¾ Access Policy: Select one number from the ¾ Enable: Check to enable the access policy. ¾ Clear the Policy: Click “Clear” button to clear all drop-down menu.
11N Wireless Broadband Router disable to access the Internet. ¾ Policy Name: Enter a name for the access policy selected. ¾ Start/End IP: Enter the starting/ending IP address. ¾ URL Strings: Specify the text strings or keywords needed to be filtered. If any part of the URL contains these strings or words, the web page will not be accessible and displayed. ¾ Times: Select the time range of client filter. ¾ Date: Select the day(s) to run the access policy.
11N Wireless Broadband Router 10.3 MAC Address Filter In order to manage the computers in LAN better, you could control the computer’s access to Internet by MAC Address Filter. ¾ MAC Address Filter: Check to enable MAC address filter. ¾ Access Policy: Select one number from the ¾ Enable: Check to enable the access policy. ¾ Clear the Policy: Click “Clear” button to clear all drop-down menu. settings for the policy.
11N Wireless Broadband Router ¾ MAC Address: Enter the MAC address you want to run the access policy. ¾ Times: Select the time range of client filter. ¾ Date: Select the day(s) to run the access policy. ¾ Apply: Click to make the settings go into effect. For example: If you want to configure the host with MAC address 00:C0:9F:AD:FF:C5 not to access the Internet at 8:00-18:00, you need to set it as above. 10.
11N Wireless Broadband Router 10.5 Remote Web Management This section is to allow the network administrator to manage the Router remotely. If you want to access the Router from outside the local network, please select the “Enable”. ¾ Enable: Check to enable remote web management. ¾ Port: The management port open to outside access. The default value is 80. ¾ WAN IP Address: Specify the range of the WAN IP address for remote management. Note: 1.
11N Wireless Broadband Router 2. If your WAN IP address starts and ends with 0.0.0.0, it means all hosts in WAN can implement remote Web management. If you change the WAN IP address as 218.88.93.33-218.88.93.35, then only the IP addresses as 218.88.93.33, 218.88.93.34 and 218.88.93.35 can access the Router. For example: If you want to configure the IP address 218.88.93.33 to access the device’s web interface, please set it as above. 10.
11N Wireless Broadband Router Chapter 11 Routing Settings 11.1 Routing Table The main duty for a router is to look for a best path for every data frame, and transfer this data frame to a destination. So, it’s essential for the router to choose the best path, i.e. routing arithmetic. In order to finish this function, many transferring paths, i.e. routing table, are saved in the router, for choosing when needed.
11N Wireless Broadband Router Chapter 12 System Tools 12.1 Time Settings This section is to select the time zone for your location. If you turn off the Router, the settings for time disappear. However, the Router will automatically obtain the GMT time again once it has access to the Internet. ¾ Time Zone: Select your time zone from the drop-down menu. ¾ Customized time: Enter the time you customize. Note: When the Router is powered off, the time setting will be lost.
11N Wireless Broadband Router 12.2 DDNS The DDNS (Dynamic Domain Name System) is supported in this Router. It is to assign a fixed host and domain name to a dynamic Internet IP address, which is used to monitor hosting website, FTP server and so on behind the Router. If you want to activate this function, please select “Enable” and a DDNS service provider to sign up.
11N Wireless Broadband Router menu and press “Sign up” for registration. ¾ User Name: Enter the user name the same as the registration name. ¾ Password: Enter the password you set. ¾ Domain Name: Enter the domain name which is optional. For example: In the local host 192.168.0.10 establish a Web server, and register in 3322.org as follows: User name tenda Password 123456 Domain Name tenda.vicp.
11N Wireless Broadband Router 12.3 Backup/Restore Settings The device provides backup/restore settings, so you need set a directory to keep these parameters. ¾ Backup Setting: Click “Backup” button to back up the Router’s settings and select the path for save. Click “Save” to save the configuration files.
11N Wireless Broadband Router ¾ Restore Setting: Click “Browse” button to select the backup files. Click “Restore” button to restore previous settings.
11N Wireless Broadband Router 12.4 Restore to Factory Default Setting This button is to reset all settings to the default values. It means the Router will lose all the settings you have set. So please Note down the related settings if necessary. ¾ Restore: Click this button to restore to default settings. ¾ Factory Default Settings: User Name: admin Password: admin IP Address: 192.168.0.1 Subnet Mask: 255.255.255.
11N Wireless Broadband Router 12.5 Upgrade Firmware The Router provides the firmware upgrade by clicking the “Upgrade” after browsing the firmware upgrade packet which you can download from www.tenda.cn. ¾ Browse: click this button to select the upgrade file. ¾ Upgrade: click this button to start the upgrading process. After the upgrade is completed, the Router will reboot automatically. 12.
11N Wireless Broadband Router device. 12.7 Password Change This section is to set a new user name and password to better secure your router and network. ¾ User Name: Enter a new user name for the device. ¾ Old Password: Enter the old password. ¾ New Password: Enter a new password. ¾ Re-enter to Confirm: Re-enter to confirm the new password. NOTE: It is highly recommended to change the password to secure your network and the Router.
11N Wireless Broadband Router 12.8 Syslog The section is to view the system log. Click the “Refresh” to update the log. Click “Clear” to clear all shown information. If the log is over 150 records, it will clear them automatically. ¾ Refresh: Click this button to update the log. ¾ Clear: Click this button to clear the current shown log.
11N Wireless Broadband Router 12.9 Logout After you have finished the settings completely, in logout page click “Yes” to logout the web management page.
11N Wireless Broadband Router Appendix 1 Glossary Channel: An instance of medium use for the purpose of passing protocol data units (PDUs) that may be used simultaneously, in the same volume of space, with other instances of medium use(on other channels) by other instances of the same physical layer (PHY),with an acceptably low frame error ratio(FER) due to mutual interference. SSID: SSID(Service Set Identifier) is the network name shared by all devices in a wireless network.
11N Wireless Broadband Router private. same. Conversely, 104 and 128 bit are the WEP uses a common KEY to encode the data. Therefore, all devices on a wireless network must use the same key and same type of encryption. There are 2 methods for entering the KEY; one is to enter a 16-bit HEX digit. Using this method, users must enter a 10-digit number (for 64-bit) or 26-digit number (for 128-bit) in the KEY field. Users must select the same key number for all devices.
11N Wireless Broadband Router Appendix 2 Questions and Answers In this part some questions and problems shown during the Router’s usage and installation will be given suggesting answers. If your problems are not in the list, please log into our website www.tenda.cn or send an E-mail to support@tenda.cn, and we will reply you in the first time. 1. Can not login to the Web interface of the Router after you enter the IP address in the address field? Step 1: check the Router if it works well.
11N Wireless Broadband Router then repeat the ping operation. If it still does not work, please contact us. 2.Forget the login password and can not enter the setting page. What can I do? Press the “RESET” button for 7 seconds to restore the Router to default settings. 3.The computer connected with the Router shows IP address conflict. What can I do? Check if there are other DHCP servers in the LAN. If there have, disable them. The default IP address of the Router is 192.168.0.
11N Wireless Broadband Router 5.How can I configure and access the Internet via Dynamic IP? In Setup Wizard of the Web utility interface, select “Dynamic IP” connection type and click “Save” to activate it. As some ISPs bind the user computer’s MAC address, you need to clone the Router’s WAN MAC address to the bind21ing PC’s MAC address. Select “MAC Address Clone” in “Advanced Setting” to input your computer’s MAC address and click “Apply” to activate it. 6.
11N Wireless Broadband Router 80. Step 5: Input the internal server’s IP address. If your Web server’s IP address is 192.168.0.10, please input it. Step 6: select the communication protocol used by your internal host: TCP, UDP, ICMP. Step 7: click “Apply” to activate the settings. The following table has listed the well-known application and service port: Server Protocol Service Port WEB Server TCP 80 FTP Server TCP 21 Telnet TCP 23 NetMeeting TCP 1503.
