Veriton 7600GTR/7600GT/7600V Veriton 5600GT/5600V Veriton 3600GT/3600V Service Guide Service guide files and updates are available on the AIPG/CSD web; for more information, please refer to http://csd.acer.com.tw SERVICE CD PART NO.: VD.V03V3.
Revision History Please refer to the table below for the updates made on Veriton 7600GTR/GT/V, 5600GT/V and 3600GT/V service guide.
Copyright Copyright © 2003 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated. Disclaimer The information in this guide is subject to change without notice.
Conventions The following conventions are used in this manual: IV Screen messages Denotes actual messages that appear on screen. NOTE Gives bits and pieces of additional information related to the current topic. WARNING Alerts you to any damage that might result from doing or not doing specific actions. CAUTION Gives precautionary measures to avoid possible hardware or software problems. IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.
Preface Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability).
VI
Table of Contents Chapter 1 System Specifications 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Front Panel for Veriton 3600GT/V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Rear Panel for Veriton 3600GT/V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Jumper Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Main Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Chapter 6 FRU (Field Replaceable Unit) List 108 Veriton 7600GTR/GR/V Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 Veriton 5600GR/V Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents IX
Chapter 1 System Specifications Overview The Veriton 7600GTR/7600GT/7600V, 5600GT/5600V and 3600GT/3600V supports Intel® Pentium 4 processor with Hyper-Threading (HT) Technology, adding intelligence to help manage and prioritize multiple threads received from the microprocessor. This highly flexible and scalable solution meets a broad range of demanding computing needs.
Features Performance ® 4 supporting FSB up to 800 MHz or T Intel Pentium T Intel Celeron T Intel Hyper-Threading Technology supported on 3.
Front Panel for Veriton 3600GT/3600V The computer’s front panel consists of the following: Label Icon Description 1 Floppy drive LED 2 Floppy drive eject button 3 Optical drive Stop/Eject Button 4 Power button Chapter 1 3
Label Icon Description 5 Power LED 6 LAN activity LED 7 Hard disk drive activity LED 8 One button recovery slot 9 USB ports 10 Headphone-out port 11 Microphone-in port (front)* NOTE: *The system has two microphone-in ports (front and rear). However, you can not use both of them at the same time. The default setting for your system enables the microphone-in port in front and disables the one at the back.
Rear Panel for Veriton 3600GT/3600V Label Icon Color Description 1 Light blue Audio-in/Line-in jack 2 Lime Audio-out/Line-out jack 3 Pink Microphone-in jack (rear)* Chapter 1 5
Label Icon Color Description 4 Black USB ports 5 White Network port 6 Blue CRT/LCD monitor port** 7 Burgundy Parallel/printer port 8 Teal or Turquoise Serial port 9 Black USB ports 10 Purple PS/2 keyboard port 11 Green PS/2 mouse port 12 Power cord socket NOTE: * The system has two microphone-in ports (front and rear). However, you can not use both of them at the same time.
Front Panel for Veriton 5600GT/5600V The computer’s front panel consists of the following: Label Icon Description 1 Floppy drive eject button 2 Floppy drive LED 3 One button recovery slot 4 Headphone-out port 5 Microphone-in port (front)* 6 USB ports 7 Power button 8 Power LED 9 LAN activity LED 10 Hard disk drive activity LED Chapter 1 7
Label 11 Icon Description Optical drive Stop/Eject Button NOTE: *The system has two microphone-in ports (front and rear). However, you can not use both of them at the same time. The default setting for your system enables the microphone-in port in front and disables the one at the back.
Rear Panel for Veriton 5600GT/5600V Label Icon Color Description 1 Pink Microphone-in jack (rear)* 2 Lime Audio-out/Line-out jack 3 Light blue Audio-in/Line-in jack 4 Black USB ports 5 White Network port 6 Blue CRT/LCD monitor port** 7 Burgundy Parallel/printer port 8 Teal or Turquoise Serial port 9 Black Chapter 1 USB ports 9
Label Icon Color Description 10 Green PS/2 mouse port 11 Purple PS/2 keyboard port 12 Power cord socket NOTE: * The system has two microphone-in ports (front and rear). However, you can not use both of them at the same time. The default setting for your system enables the microphone-in port in front and disables the one at the back. NOTE: ** The CRT monitor port is automatically disabled when an add-on AGP VGA card is installed into the system (for Intel 865G chipset).
Front Panel for Veriton 7600GTR/7600GT/7600V The computer’s front panel consists of the following: Label Icon Description 1 USB ports 2 Microphone-in port (front)* 3 Speak-out/line-out port Chapter 1 11
Label Icon Description 4 Optical drive Stop/Eject Button 5 Optical drive Stop/Eject Button 6 Floppy drive LED 7 Floppy drive eject button 8 One button recovery slot 9 Power button 10 Power LED 11 LAN activity LED 12 Hard disk drive activity LED NOTE: *The system has two microphone-in ports (front and rear). However, you can not use both of them at the same time. The default setting for your system enables the microphone-in port in front and disables the one at the back.
Rear Panel for Veriton 7600GTR/7600GT/7600V Label Icon Color Description 1 Light blue Audio-in/Line-in jack 2 Lime Audio-out/Line-out jack Chapter 1 13
Label Icon Color Description 3 Pink Microphone-in jack (rear)* 4 White Network port 5 Black USB ports 6 Blue CRT/LCD monitor port** 7 Burgundy Parallel/printer port 8 Teal or Turquoise Serial port 9 Black USB ports 10 Purple PS/2 keyboard port 11 Green PS/2 mouse port 12 Power cord socket 13 Power cord socket NOTE: * The system has two microphone-in ports (front and rear). However, you can not use both of them at the same time.
System Block Diagram VRM 10 ST L6710 2-Phase PWM Block Diagram Intel mPAG478B Processor FSB 4X/8X AGP 1.
Keyboard The keyboard has full-sized keys that include separate cursor keys, two Windows keys, and twelve function keys. Lable Key Description 1 Sleep button Puts the system to sleep when pressed this button. 2 Internet/E-mail/Search keys Consist of three buttons: 3 4 Multimedia keys Volume control/Mute keys • Web browser : launches the browser application that came bundled with your system. • E-mail : launches the e-mail application that came bundled with your system.
Lable 5 Key Scroll Lock Key [ 6 Num Lock Key ] 7 Cursor keys Description When activated, the screen moves one line up or down when you press the up arrow or down arrow respectively. Take note that [may not work with some applications. When activated, the keypad is set to numeric mode, i.e., the keys function as a calculator (complete with arithmetic operators such as +, -, * and /). Also called arrow keys, let you move the cursor around the screen.
Hardware Specifications and Configurations Processor Item Specification Type Intel® Pentium 4 1.8 ~ 3.2GHz FSB400/533/800MHz Intel® Celeron 2.0 ~ 2.6GHz and above Slot Socket 478 Speed Internal: 1.4 ~ 3.2GHz+ External: 400/533/800MHz Data Bus Frequency for Springdale-G. Minimum operating speed 0 MHz (If Stop CPU Clock in Sleep State the BIOS Setup is set to Enabled.) Voltage Processor voltage can be detected by the system without setting any jumper.
Cache Memory Item Specification First-Level Cache Configurations Cache function control Enable/Disable by BIOS Setup (Advanced options) Second-Level Cache Configurations: Below information is only applicable to system with installed Pentium 4 processor.
Floppy disk drive Interface Item Specification Vendor & Model Name Panasonic JU-256A048P Mitsumi D353M3D-R694005 NEC FD1231T-STD-R2 Floppy Disk Specifications Media Recognition 1.
USB Port Items Universal UHCI Specifications USB 1.1 Universal EHCI USB 2.
A-2 Input voltage Nominal Voltage Variation Range 100 - 120 VRMS 90-132 VRMS 200 - 240 VRMS 180-264 VRMS A-3 Input current Input Current Measuring Range 6A 90 -132 VRMS 3A 180 - 264 VRMS (This is 200W power supply) T This “4A” includes the outlet supply current: 2A T Measure at line input 90 VRMS and maximum load condition. 200W Power Supply Output Requirements Regulation Current Rating (Max) +5V +5% 18A +12V +5% 14A -12V +10% 0.5A +3.3V +5% 14A +5VSB +5% 2A NOTE: 1.
Memory Channel Mode Single Channel / Virtual Single Channel Dual Channel DIMM Population No restrictions Matching DIMM pairs Rank(Row) Size Size of one side of the DIMM populated in the channel 2x the size of one side of the DIMM populated in the channel(A or B) (64MB - 512MB) (128MB - 1GB) Number of Ranks(Rows) 8 maximum 4 maximum Channel Size 64 bits 128 bits Page Size Size read from DIMM 2 x Size read from DIMM Burst Length Memory Channel Channel A (4KB, 8KB, 16KB) (8KB, 16KB, 32KB)
DIMM 1 DIMM 2 128MB~1GB DIMM3 DIMM4 128MB~1GB 128MB~1GB 128MB~1GB 128MB~1GB Total 256MB~2GB 128MB~1GB 128MB~1GB 256MB~2GB 128MB~1GB 512MB~4GB The following conditions must be met: T T Matched DIMM configuration in each channel T Same Density (128MB, 256MB, 512MB, etc.
Maximizing Performance Optimal configurations for highest performance: T Matched, DDR400, Double-sided DIMMs T Dual Channel Mode (Symmetrical DIMM population) Lightly Loaded Config or Ch B Ch A MCH T Ch B Ch A MCH Matched, DDR400, Dual Channel Mode Fully Loaded Config or Ch B Ch A Ch B Ch A MCH MCH When not using DDR400, highest performing configuration: T Symmetrical DIMM population with matched double-sided DIMMs T Lightly loaded memory population aids in higher performance T x8 Bu
Chapter 2 System Utilities Most systems are already configured by the manufacturer or the dealer. There is no need to run Setup when starting the computer unless you get a Run Setup message. The Setup program loads configuration values into the battery-backed nonvolatile memory called CMOS RAM. This memory area is not part of the system RAM. NOTE: If you repeatedly receive Run Setup messages, the battery may be bad. In this case, the system cannot retain configuration values in CMOS.
Entering Setup To enter Setup, press the key c during the POST (Power-on self-test). NOTE: You must press c simultaneously while the system is booting. The Setup Utility main menu then appears: The above screen is the BIOS Utility Basic Level screen. It allows you to view and change only the basic configuration of your system. The command line at the bottom of the menu tells you how to move within a screen and from one screen to another.
Product Information The screen below appears if you select Product Information from the main menu: The Product Information menu contains general data about the system, such as the product name, serial number, BIOS version, etc. These information is necessary for troubleshooting (maybe required when asking for technical support). The following table describes the parameters found in this menu: Parameter Product Name Description Displays the model name of your system.
Standard CMOS Features Select “Standard CMOS Features” from the main menu to configure the drives installed in your system. The following screen shows the Disk Drives menu: The following table describes the parameters found in this menu. Parameter Date Description Options Lets you set the date following the weekday-month-day- Weekday: Sun, Mon....Sat year format Month: Jan, Feb...
Parameter IDE Channel 1 Slave Description Options Lets you configure the hard disk drive connected to the slave port of IDE channel 1. To enter the IDE Channel 1 Slave setup, press e. (Show the Status:) None HDD or CD-ROM Number The IDE CD-ROM is always automatically detected. Drive A Allows you to configure your floppy drive A. 1.44 MB, 3.5-inch None 360 KB, 5.25-inch 1.2 MB, 5.25-inch 720 KB, 3.5-inch 2.88 MB, 3.5-inch Drive B Allows you to configure your floppy drive B. None 360 KB, 5.
IDE Channel 0 Master/Slave and IDE Channel 1 Master/Slave Setup The following screen appears if you select any of the IDE drive parameters: The following table describes the parameters found in this menu. Parameter IDE HDD Auto-Detection Description Auto-detects your hard disk drive.
Advanced BIOS Features The following screen shows the Advanced BIOS Features. The following table describes each Advanced BIOS Features parameter. Settings in boldface are the default and suggested settings. Parameter Hard Disk Boot Priority Description Selects the hard disk boot priority.
Parameter Description Options Quick Power On Self Test This parameter speeds up POST by skipping some items that are normally checked. Enabled First Boot Device This parameter allows you to specify the system boot up search sequence. Floppy, LS120, Hard Disk, CD-ROM, ZIP100, LAN (on board LAN-- Boot from LAN), Disabled Disabled Second Boot Device This parameter allows you to specify the system boot up search sequence.
Parameter MPS Version Control For OS Description This field allows you to select which MPS (MultiProcessor Specification) version to be used for the operating system. Options 1.4 1.1 OS Select For DRAM > 64MB This item is only required if you have installed more Non-OS2 than 64MB of memory and you are running the OS/ OS2 2 operating system. HDD S.M.A.R.T. Capability The S.M.A.R.
Advanced Chipset Features The following screen shows the Advanced Chipset Features. The following table describes each Advanced Chipset Features parameter. Settings in boldface are the default and suggested settings. Parameter Options Selects whether DRAM timing is controlled by the SPD (Serial Presence Detect) EEPROM on the DRAM module. Setting to By SPD enables DRAM timings to be determined by BIOS based on the configurations on the SPD.
Parameter Description Options DRAM RAS# Precharge This item controls the number of cycles for Row Address Strobe (RAS) to be allowed to precharge. If insufficient time is allowed for the RAS to accumulate its charge before DRAM refresh, refresh may be incomplete and DRAM may fail to retain data. This item applies only when synchronous DRAM is installed in the system.
Integrated Peripherals The following table describes each Integrated Peripherals parameter. Settings in boldface are the default and suggested settings. OnChip IDE Device Press [Enter] to enter the sub-menu and the following screen appears: Parameter Options Block mode is also called block transfer, multiple commands, or multiple sector read/write.
Parameter Description Options Ultra DMA/33 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver. If your hard drive and your system software both support Ultra DMA/33, Ultra DMA/66 and Ultra DMA/100 select Auto to enable BIOS support. Auto SATA Mode Select SATA Mode IDE, RAID On-Chip Serial ATA This setting is used to specify the SATA controller.
Parameter USB Mouse Support AC97 Audio Onboard LAN Control Description Options This item lets you enable or disable the USB mouse driver within the onboard BIOS. The keyboard driver simulates legacy mouse command and lets you use a USB mouse during POST or after boot if you do not have a USB driver in the operating system. Enabled Auto allows the motherboard’s BIOS to detect whether you’re using any audio device. If so, the onboard audio controller will be enabled.
Power Management Setup The Power Management menu lets you configure the system power-management feature. It works only in APM mode. IMPORTANT:If an ACPI-aware operating system such as Windows 98 or Windows 2000 is installed in ACPI mode, the operating system will use the ACPI interfaces. Then the settings in Power Management page is non-effective.
The following table describes the parameters found in this menu. Parameter ACPI Function Description Enabled/Disable ACPI Function. Options Enabled Disabled ACPI Suspend Type This item specifies the power saving modes for ACPI function. Options are: S1/POS S3/STR S1/POS: The S1 sleep mode is a low power state. In this state, no system context is lost (CPU or chipset) and hardware maintains all system context.
Parameter Description Options Suspend Mode If system activity is not detected for the length of time specified in this field, all devices except CPU will be shut off. Disabled, 1 Min, 2 Min, 4 Min, 8 Min, 12 Min, 20 Min, 30 Min, 40 Min, 1 Hour HDD Power Down If HDD activity is not detected for the length of time specified in this field, the hard disk drive will be powered down while all other devices remain active. Disabled This is a specification of ACPI and supported by hardware.
PnP/PCI Configurations The table below describes each PnP/PCI configuration parameter. Settings in boldface are the default and suggested settings. Parameter PNP OS Installed Reset Configuration Data Resources Controlled By 43 Description Options When set to [Yes], BIOS will only initialize the PnP cards used for booting (VGA, IDE, SCSI). The rest of the cards will be initialized by the PnP operating system like Windows 98. When set to [No], BIOS will initialize all the PnP cards.
Parameter IRQ Resources DMA Resources Description Options The items are adjustable only when Resources Controlled By is set to Manual. Press and you will enter the sub-menu of the items. Legacy ISA for devices compliant with the original PC AT bus specification, PCI/ISA PnP for devices compliant with the Plug and Play standard whether designed for PCI or ISA bus architecture.
PC Health Status Parameter Chassis Intrusion Detect CPU Temperature, Ambient Temperature, VCore (From VID), +2.5V Vccp, +3.3V, +5V, +12V, HVcc, +1.5V, +1.8V, CPU FAN Speed, System FAN Speed 45 Description The field enables or disables the feature of recording the chassis intrusion status and issuing a warning message if the chassis is once opened. To clear the warning message, set the field to Reset. The setting of the field will automatically return to Enabled later.
Frequency Control The following table describes the parameters found in this menu. Parameter Description CPU Clock Ratio Core Clock Frequency to System Bus Ratio (RO) Auto Detect PCI CLK This option allows you to enable/disable the feature of auto detecting the clock frequency of the installed PCI bus.
Load Optimized Settings You need to reload the BIOS default settings every time you make changes to your system hardware configuration (such as memory size, CPU type, hard disk type, etc.); otherwise, BIOS will keep the previous CMOS settings. Selecting this option displays the following dialog box: Choosing Yes enables BIOS to automatically detect the hardware changes that you have made in your system. This option also allows you to restore the default settings.
System Security The Setup program has a number of security features to prevent unauthorized access to the system and its data. Set Supervisor Password To set a password: 1. At the prompt, type your password. Your password can be up to 8 alphanumeric characters. When you type the characters, they appear as asterisks on the password screen box. 2. After typing the password, press e. 3. At the next prompt, re-type your password and press e again to confirm the new password.
Set User Password IMPORTANT:To show the “Set User Password”: 1. Choose “Set Supervisor Password” and press e. 2. Type the password and then press e. 3. Confirm the password, and then press e. 4. The screen as below with “Set User Password” enabled will be shown. To set a password: 1. At the prompt, type your password. Your password can be up to 8 alphanumeric characters. When you type the characters, they appear as asterisks on the password screen box. 2. After typing the password, press e. 3.
Clear CMOS Follow these steps to bypass the password: 1. Reset CMOS, by adjusting JBAT1 to 2-3 2. Reboot the system. 3.
Save & Exit Setup Highlight this item and press to save the changes that you have made in the Setup Utility and exit the Setup Utility. When the Save and Exit dialog box appears, press to save and exit, or press to return to the main menu.
Exit Without Saving Highlight this item and press to discard any changes that you have made in the Setup Utility and exit the Setup Utility. When the Exit Without Saving dialog box appears, press to discard changes and exit, or press to return to the main menu. NOTE: If you have made settings that you do not want to save, use the "Exit Without Saving" item and press to discard any changes you have made.
Intel Serial ATA RAID Introduction The southbridge ICH5R provides a hybrid solution that combines two independent SATA ports for support of up to two Serial ATA (Serial ATA RAID) drives. Serial ATA (SATA) is the latest generation of the ATA interface. SATA hard drives deliver blistering transfer speeds of up to 150MB/sec. Serial ATA uses long, thin cables, making it easier to connect your drive and improving the airflow inside your PC. 1. Supports 150 MB/s transfers with CRC error checking 2.
(3) Chapter 2 Combined Mode: S-ATA devices and P-ATA devices. Maximum of 2 devices each, thus total 4 devices at maximum.
Native Mode: T In this mode, system BIOS will search all available IRQs to use for HDD. T New OS that support switch to Native Mode (WinXP, Windows .NET Server) can set SATA and PATA to Native Mode. T Comprehend both Legacy and/or Native Modes. T Maximum 6 ATA devices to connect (4 for P-ATA & 2 for S-ATA). NOTE: Proper support: BIOS provides a BIOS setup option for Native Mode or Legacy Mode user selection.
RAID BIOS Configuration The Intel RAID Option ROM should be integrated with the system BIOS on all motherboards with a supported Intel chipset. Please use b+ keys to enter the “Intel(R) RAID for Serial ATA” status screen, which should appear early in system boot-up, during the POST (Power-On Self Test). Using the Intel RAID Option ROM 1.
(1) Create RAID Volume: Select this option and press e. The following screen appears: Specify a RAID Volume name and then press the vor ekey to go to the next field. Select the strip value for the RAID 0/1 array by scrolling through the available values by using the wor y keys and pressing the ekey to select and advance to the next field. The available values range from 4KB to 128 KB in power of 2 increments. The strip value should be chosen based on the planned drive usage.
NOTE: RAID 1 can not select Strip Size. From the Strip size, press the vor ekey to advance to the Create Volume prompt.
Press to confirm the selection or press to create the RAID volume again. Then you will return to the main menu with an updated status as follows: Scroll to option 4 Exit and press eto exit the RAID Configuration utility.
Click to confirm the exit. (2) Delete RAID Volume: Here you can delete the RAID volume, but please be noted that all data on RAID drives will be lost. NOTE: If your system currently boots to RAID and you delete the RAID volume in the Intel RAID Option ROM, your system will become unbootable. Select option 2 Delete RAID Volume from the main menu window and press ekey to select a RAID volume for deletion.
Select the volume and press ckey to delete the RAID volume. The following prompt appears: Press key to accept the volume deletion. (3) Reset Disks to Non-RAID: Select option 3 Reset Disks to Non-RAID and press eto delete the RAID volume and remove any RAID structures from the drives. The following screen appears: Press key to accept the selection. NOTE: You will lost all data on the RAID drives and any internal RAID structures when you perform this operation.
RAID 0 RAID 0 uses an algorithm to break files into smaller files of the user defined size called the stripe size. Once a file is broken down into these stripes, each drive in the array receives one or more of these fragments. For example, if there are two drives in a RAID 0 array with a 64KB stripe size and the RAID controller gets a command to write a single 128KB file, the file is broken down into two 64KB stripes.
RAID 1 RAID 1 works by writing identical sets of information to two drives in an array. When the controller is sent a 64KB file to be written to a two disk RAID 1 array, the controller sends identical copies of this 64KB file to both disks in the array. Reads are the same as on a single drive: the controller requests the file from one of the two drives. The special feature of RAID 1 is its fault tolerance. If either of the two drives in the array fails, no data is lost.
Chapter 3 Machine Disassembly and Replacement This chapter contains step-by-step procedures on how to disassemble the Veriton 7600GTR/GT/V, 5600GT/V and 3600GT/V desktop computer for maintenance and troubleshooting. To disassemble the computer, you need the following tools: ! Wrist grounding strap and conductive mat for preventing electrostatic discharge ! Flat-bladed screwdriver ! Phillips screwdriver ! Hexagonal screwdriver Plastic stick NOTE: The screws for the different components vary in size.
General Information Before You Begin Before proceeding with the disassembly procedure, make sure that you do the following: 1. Turn off the power to the system and all peripherals. 2. Unplug the AC adapter and all power and signal cables from the system.
Disassembly Procedure Flowchart The flowchart on the succeeding page gives you a graphical representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing.
Veriton 5600GT/V Chapter 3 67
Veriton 3600GT/V 68 Chapter 3
Disassembling the Veriton 7600GTR/GT/V Opening the Housing This section tells you how to open the housing cover when you need to install additional components inside the system unit. CAUTION: Before you proceed, make sure that you have turned off the system and all peripherals connected to it. Removing the Housing 1. Turn off the system power and unplug all cables. 2. Remove the two screws holding the upper cover 3.
. 70 3. Disconnect the HDD cable and HDD power cable from the HDD. 4. Pull the ODD lock and then detach the ODD from the frame. 5. Pull the FDD lock and then detach the FDD from the frame. 6. Press the right and left HDD holders and then detach the HDD carefully. 7. Remove the left ODD holder. 8. Remove the left FDD holder. 9. Remove the left and right HDD holders.
Removing the Internal Cables/Connectors and Memory 1. Disconnect the main power connector from the main board. 2. Disconnect the 12-voltage power connector from the main board. . 3. Disconnect the FDD cable, ODD cable and HDD cable from the main board. 4. Press the leavers on the both sides of the DIMM socket outward to release the DIMM, and then gently pull the DIMM out to remove it. 5. Disconnect the front panel audio connector from the main board. 6.
7. Disconnect the internal speaker connector from the main board. 8. Disconnect the LAN LED connector from the main board. 9. Disconnect the one button recovery connector, chassis intrusion switch connector, front panel connectors, and system fan connector from the main board. Removing the CPU Fan Sink, CPU and System Fan 72 1. Disconnect the CPU fan connector from the main board. 2. Remove the two latches on both side of the fan sink. 3. Remove the CPU fan sink from the main board. 4.
6. Remove the four screws holding the system fan. 7. Take out the system fan. Removing the Power Supply and Main Board 1. Remove the four screws holding the power supply on the rear side. 2. Detach the power supply from the housing carefully. 3. Remove the eight screws holding the main board as the picture shows. 4. Detach the main board from the lower case carefully. . Removing the Upper Cover and Daughter Board Module 1. Remove the two screws holding the upper cover as the picture shows. 2.
3. Detach the upper cover from the housing carefully. 4. Remove the four screws holding the daughter board plate. 5. Remove the daughter board plate. 6. Remove the daughter board top cover as the picture shows. . 7. Cut the cable clamp holding the two front USB cables and front panel audio cable. 8. Remove the daughter board module from the upper cover. . 9. Remove the daughter board plate from the daughter board module. 10. Remove the two screws holding the daughter board. 11.
Removing the Intrusion Alarm and LCD Module 1. Remove the two screws holding the intrusion alarm, and then take out the intrusion alarm . 2. Remove one screw holding the LED module holder. 3. Remove the LED module as the picture shows. . 4. Remove one screw holding the reset button holder as the picture shows. 5. Pull out the reset cable carefully. .
Disassembling the Veriton 5600GT/V Opening the Housing This section tells you how to open the housing cover when you need to install additional components inside the system unit. CAUTION: Before you proceed, make sure that you have turned off the system and all peripherals connected to it. Removing the Housing 1. Remove the two screws holding the upper cover. 2. Slide the upper cover out and then gently pull it outward to detach it from the housing. . Removing the ODD/FDD/HDD 76 1.
. 5. Disconnect the FDD power cable and FDD cable from the FDD. 6. Pull the FDD lock and then detach the FDD from the frame. . 7. Disconnect the HDD cable and HDD power cable from the HDD. 8. Press the right and left HDD holders and then detach the HDD carefully. 9. Remove the right ODD holder. 10. Remove the left FDD holder. 11. Remove the left and right HDD holders.
Removing the Internal Cables/Connectors and Memory 1. Disconnect the main power connector from the main board. 2. Disconnect the 12-voltage power connector from the main board. . 3. Disconnect the FDD cable, ODD cable and HDD cable from the main board. 4. Press the leavers on the both sides of the DIMM socket outward to release the DIMM, and then gently pull the DIMM out to remove it. Removing the CPU Fan Sink and CPU 78 1. Disconnect the CPU fan connector from the main board. 2.
4. Pull the socket lever up to 90 degree and then pull out the CPU from the socket. 5. Put the socket lever back to the original position. Removing the Internal Cables/Connectors and Memory 1. Disconnect the front panel audio connector from the main board. 2. Disconnect the two front USB connectors from the main board. 3. Disconnect the LAN LED connector from the main board. 4.
3. Remove the four screws holding the power supply on the rear side. 4. Detach the power supply from the housing carefully. . 5. Remove the eight screws holding the main board as the picture shows. 6. Detach the main board from the lower case carefully. . Removing the LED Module and Daughter Board Module 80 1. Remove one screw holding the LED module holder. 2. Remove the LED module as the picture shows. 3.
4. Remove one screw holding the daughter board bracket. 5. Remove the daughter board module as the picture shows. . 6. Disconnect the front panel audio connector from the daughter board. 7. Disconnect the two front USB connectors from the daughter board. . 8. Remove the two screws holding the daughter board. 9. Remove the daughter board from the daughter board bracket.
Disassembling the Veriton 3600GT/V Opening the Housing This section tells you how to open the housing cover when you need to install additional components inside the system unit. CAUTION: Before you proceed, make sure that you have turned off the system and all peripherals connected to it. Removing the Housing 1. Remove the three screws holding the upper cover. 2. Slide the left cover out and then gently pull it outward to detach it from the housing. . Removing the FDD/ODD/HDD 82 1.
. 4. Disconnect the HDD cable and HDD power cable from the HDD. 5. Pull the ODD lock and then detach the ODD from the frame. . 6. Pull the FDD lock and then detach the FDD from the frame. 7. Press the right and left HDD holders and then detach the HDD carefully. 8. Remove the left ODD holder. 9. Remove the left FDD holder. 10. Remove the left and right HDD holders.
Removing the Internal Cables/Connectors and Memory 1. Remove the air duck as the video shows. 2. Disconnect the HDD cable, ODD cable, and FDD cable from the main board. 3. Disconnect the main power connector from the main board. 4. Disconnect the 12-voltage power connector from the main board. . 5. 84 Press the leavers on the both sides of the DIMM socket outward to release the DIMM, and then gently pull the DIMM out to remove it.
Removing the Internal Cables/Connectors 1. Disconnect the front panel audio connector from the main board. 2. Disconnect the two front USB connectors from the main board. 3. Disconnect the LAN LED connector from the main board. 4. Disconnect the internal speaker connector from the main board. 5. Disconnect the one button recovery connector, chassis intrusion switch connector, front panel connectors, and system fan connector from the main board. Removing the CPU Fan Sink and CPU 1.
4. Pull the socket lever up to 90 degree and then pull out the CPU from the socket. 5. Put the socket lever back to the original position. Removing the System Fan and Main Board 1. Remove the two screws holding the system fan. 2. Take out the system fan. 3. Remove the eight screws holding the main board as the picture shows. 4. Detach the main board from the lower case carefully. . Removing the Intrusion Alarm, Daughter Board Module and LCD Module 1.
. 2. Remove the front panel as the video shows. 3. Disconnect the front panel audio connector from the daughter board. 4. Disconnect the two front USB connectors from the daughter board. . 5. Remove one screw holding the daughter board bracket. 6. Remove the daughter board module as the video shows. . 7. Remove the two screws holding the daughter board. 8. Remove the daughter board from the daughter board bracket. .
9. Pull the internal speaker cable, front panel cables, LAN LED cable and one button recovery cable as the video shows. . 10. Remove one screw holding the LED module holder. 11. Remove the LED module as the video shows. . 12. Remove the reset button as the video shows. 13. Pull out the reset cable carefully. . Removing the Upper Case and Power supply 88 1. Remove one screw holding the upper cover. 2. Remove the upper cover as the video shows. 3.
Chapter 3 89
Chapter 4 Troubleshooting This chapter provides troubleshooting information for the Veriton 7600GTR/7600GT/7600V, 5600GT/5600V and 3600GT/3600V.
Power-On Self-Test (POST) Each time you turn on the system, the Power-on Self Test (POST) is initiated. Several items are tested during POST, but is for the most part transparent to the user. The Power-On Self Test (POST) is a BIOS procedure that boots the system, initializes and diagnoses the system components, and controls the operation of the power-on password option.
. Checkpoint 04h 05h Description Reserved 1. Blank out screen 2. Clear CMOS error flag 06h Reserved 07h 1. Clear 8042 interface 2. Initialize 8042 self-test 08h 1. Test special keyboard controller for Winbond 977 series Super I/O chips. 2. Enable keyboard interface. 09h Reserved 0Ah 1. Disable PS/2 mouse interface (optional) 2. Auto detect ports for keyboard & mouse followed by a port & interface swap (optional). 3. Reset keyboard for Winbond 977 series Super I/Q chips.
. Checkpoint 23h Description 1. Check validity of RTC value: e.g. a value of 5Ah is an invalid value for RTC minute. 2. Load CMOS settings into BIOS stack. If CMOS checksum fails, use default value instead. 3. Prepare BIOS resource map for PCI & PnP use. If ESCD is valid, take into consideration of the ESCD’s legacy information. 4. Onboard clock generator initialization. Disable respective clock resource to empty PCI & DIMM slots. 5.
. Checkpoint Description 43h Test 8259 functionality 44h Reserved 45h Reserved 46h Reserved 47h Initialize EISA slot 48h Reserved 49h 1. Calculate total memory by testing the last double word of each 64K. 4Ah Reserved 4Bh Reserved 4Ch Reserved 2. Program writes allocation for AMD K5 CPU. 4Dh Reserved 4Eh 1. Program MTRR of M1 CPU. 2. Initialize L2 cache for P6 class CPU & program CPU with proper cacheable range. 3. Initialize the APIC for P6 class CPU. 4.
. Checkpoint 67h Description Prepare memory size information for function call: INT 15h ax=E820h 68h Reserved 69h Turn on L2 cache 6Ah Reserved 6Bh Program chipset registers according to items described in Setup& Auto-configuration table. 6Ch Reserved 6Dh 1. Assign resources to all ISA PnP devices. 2. Auto assign ports to onboard COM ports if the corresponding item in Setup is set to “AUTO” 6Eh Reserved 6Fh 1. Initialize floppy controller 2. Set up floppy related fields in 40: hardware.
. Checkpoint 85h Description 1. USB final Initialization 2. NET PC: Build SYSID structure 3. Switch screen back to text mode. 4. Set up ACPI table at top of memory. 5. Invoke ISA adapter ROMs. 6. Assign IRQs to PCI devices 7. Initialize APM 8. Clear noise of IRQs 86h Reserved 87h Reserved 88h Reserved 89h Reserved 90h Reserved 91h Reserved 92h Reserved 93h Read HDD boot sector information for Trend Anti-Virus code 94h 1. Enable L2 cache 2. Program boot up speed 3.
POST Error Messages List If you cannot run the diagnostics program tests but did receive a POST error message, use “POST Error Messages List” to diagnose system problems. If you did not receive any error message, look for a description of your error symptoms in “Error Symptoms List” on page 120. NOTE: When you have deemed it necessary to replace an FRU, and have done so, you must run a total system check to ensure that no other activity has been affected by the change.
BIOS Messages Action/FRU Memory Test: This message displays during a full memory test, counting down the memory areas being tested. Memory test fail If POST detects an error during memory testing, additional information appears giving specifics about the type and location of the memory error.
Error Symptoms List NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/ FRU listed in right column is the most likely cause.
Error Symptom Action/FRU Diskette drive LED comes on for more than 2 minutes when reading data. 1. 2. 3. 4. Diskette Diskette drive connection/cable Diskette drive Main board Diskette drive LED fails to light, and the drive is unable to access for more than 2 minutes. 1. 2. 3. 4. 5. Diskette Diskette drive power Diskette drive connection/cable Diskette drive Main board Diskette drive test failed. 1. 2. 3. 4.
Error Symptom Action/FRU Audio Audio software program invokes but no sound comes from speakers. 1. Speaker power/connection/cable. Modem Modem ring cannot wake up system from suspend mode. 1. For the External Modem, make sure Power on By Ring in BIOS Setup or Power Management is set to Enabled. For the PCI modem, make sure Wake up by PCI card is set to Enabled. 2. If PCI modem card is used, reinsert the modem card to PCI slot firmly or replace the modem card. 3.
Error Symptom Action/FRU Parallel/Serial Ports Execute “Load BIOS Default Settings” in BIOS Setup to confirm ports presence before diagnosing any parallel/serial ports problems. Serial or parallel port loop-back test failed. 1. Make sure that the LPT# or COM# you test is the same as the setting in BIOS Setup. 2. Loop-back. 3. Main board. Printing failed. 1. Ensure the printer driver is properly installed. Refer to the printer service manual. 2. Printer. 3. Printer cable. 4. Main board.
Undetermined Problems If an error message is present, go to “POST Error Messages List” on page 118. If you did not receive any messages, if the symptom is listed in “or “Error Symptoms List” on page 120. If you still cannot solve the problem, continue with this check: 1. Check the power supply voltages. If the voltages are correct continue with the following steps: 2. Power off the system unit. 3. Perform the following checks, one by one, until you have isolated the problem FRU. 4.
Chapter 5 Jumper and Connector Information Jumpers and Connectors Refer to the following figure for the location of the jumpers and connectors on the main board: CPUFAN1 CPU D_LED1 COM2 DDR DIMMs ATX1 Back Panel I/O FDD1 JPW1 IDE1 & IDE2 JUSB_MS JLAN LED1 SATA1, SATA2 AGP Slot JLAN1 SYSFAN1 JSPK JBAT1 PCI Slots JFP1 J3 JAUD1 JBIOS1 JUSB2 & JSUB3 JGP3 JCI1 JRECOVER JGP1 JGP2 Parallel Mouse LAN (Optional) L-In USB Ports Keyboard COM A VGA Port USB Ports L-Out Mic-In (for Springdale-
Jumper and Connector Description Label Component Label Component JPW1 ATX 12V Power Connector JCI1 Chassis Intrusion Switch Connector CPUFAN1 Processor Fan Connector JBAT1 Clear CMOS Jumper D_LED1 D Bracket 2 Connector JBIOS1 BIOS Flash Jumper COM1 9-pin Serial Port JRECOVER System Recovery Switch Connector FDD1 FDD Connector USB2/3 Front USB Connectors ATX1 20-pin Power Connector PCI1~3 Peripheral Component Interconnecto Slots IDE2/1 Ultra ATA HDD Connectors JAUD1 Front Panel
Main Board Layout D_LED1 Top : mouse Bottom: keyboard COM2 CPUFAN1 USB ports Top : Parallel Port Bottom: COM A VGA port FDD 1 ATX Power Supply SMCS LPC47M192-NC JPW1 Top: LAN jack Bottom: USB ports Intel Springdale JUSB_MS PCI Slot 1 IDE 2 DDR 3 DDR 4 DDR 1 JLAN1 DDR 2 AGP Slot Broadcom BCM5705 SATA2 JSPK PCI Slot 2 JCI1 CD1 BATT + Codec Intel ICH5/5R SATA1 IDE 1 JLAN LED1 T:Line-In M: Line-Out B:Mic SYSFAN1 JFP1 JBAT1 PCI Slot 3 JGP2 JGP1 JRECOVER JAUD1 USB2 USB3 Chapt
107 Chapter 5
Chapter 6 FRU (Field Replaceable Unit) List This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Veriton 7600GTR/ GT/V, 5600GT/V and 3600GT/V. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). IMPORTANT: Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel.
Veriton 7600GTR/7600GT/7600V Exploded Diagram ˆ ˇ ˄ ˃ ʳˌ ʳˋ ʳˊ ʳˉ ʳˈ ʳˇ ʳˆʳ ʳ ʳ˄ ˅˃ ˅˄ ˋ ˊ ˈ 109 ˄ˌ ˅˅ ˅ˆ ˅ˇ ˅ˈ ˉ Chapter 6
Veriton 5600GT/5600V Exploded Diagram ˆ ˄˄ ˇ ˄˃ ʳˌ ʳˋ ʳˊ ʳˉ ʳˇ ʳˈ ʳˆ ʳ ʳ˄ ˅˄ ˊ ˋ ˌ ˅ˆ ˅˅ ˉ ˈ Chapter 6 110
Veriton 3600GT/3600V Exploded Diagram ˈ ˆ ˄˄ ˃ ʳˌ ʳˋ ʳˊ ˇ ʳˉ ʳˈ ʳˇ ʳ˅ ʳˆ ʳ˄ ˅ˇ ˅˅ ˅ˆ ˅ˈ ˅ˉ ˅˄ ˅˃ ˋ ˄ˉ 111 ˌ ˄ˊ Chapter 6
Picture Part Name Part Number CPU/Processor CELERON 2.0G SOCKET 478, D1 KC.DCD01.20A Celeron 2.4G Socket 478, D1 KC.DCD01.24A Celeron 2.5G Socket 478, D1 KC.DCD01.25A Celeron 2.6G Socket 478, D1 KC.DCD01.26A Celeron 2.7G Socket 478, D1 KC.DCD01.27A Celeron 2.8G Socket 478, D1 KC.DCD01.28A Northwood 2.4G Socket 478 KC.DP001.24C Northwood 2.6G Socket 478 KC.DP001.26C Northwood 2.8G Socket 478 KC.DP001.28C Northwood 3.0G Socket 478 KC.DP001.30C Northwood 3.06G Socket 478, D1 KC.DPD01.
Picture Part Name Part Number Hard Disk Drive HDD 80GB 7200RPM SATA SEAGATE ALPINE ST380013AS KH.08001.005 HDD 120G 7200RPM SATA SEAGATE ALPINE ST3120026AS KH.12001.005 HDD 160G 7200RPM SATA SEAGATE ALPINE ST3160023AS KH.16001.004 HDD 40GB/5400RPM/ATA-100 /SEAGATE C2 ST340015A KH.04001.002 HDD U9 80G 5400RPM SEAGARE ST380012A KH.08001.002 HDD 120GB 5400RPM ATA-100 SEAGATE U9 ST3120025A KH.12001.002 HDD 40GB 7200RPM SEAGATE CUDA VI ALPINE ST340014A KH.04001.
Picture Part Name Part Number For VT3600 FDD CABLE 34PIN 2CON 50.V02VF.301 HDD IDE CABLE 40PIN (SHORT) 50.V02VF.302 ODD CABLE 40PIN (LONG) 50.V02VF.303 AUDIO CABLE 10PIN 2CON 50.V02VF.304 USB CABLE 10PIN 2CON 50.V02VF.305 LED CABLE (LAN, POWER/ HDD) POWER BUTTON BOARD W/ BRACKET 50.V02VF.306 RESET CABLE 50.V02VF.307 INTRUSION ALARM CABLE 2PIN 50.V02VF.308 LAN CABLE 50.V02VF.309 POWER/ HDD LED CABLE 50.V02VF.310 For VT5600 FDD CABLE 34PIN 2CON 50.V02VF.
Picture Part Name Part Number Add-on Card VGA CARD RADEON 9200 64MB DDR LP W/TV-OUT NTSC/ LP BRACKET FIC TI-4200-8X VG.A9207.003 VGA CARD RADEON 9200 64MB DDR LP W/TV-OUT PAL/LP BRACKET FIC TI-4200-8X VG.A9207.004 VGA CARD FX 5200 64MB W/TW-OUT PAL LP BRACKET LEADTEK LR2967 VG.29604.005 VGA CARD FX5200 64MB W/TW-OUT NTSC LP BRACKET LEADTEK LR2967 VG.29604.006 VGA CARD XABRE200 AGP 8X 32M LP BRACKET VG.20005.002 MODEM CARD 56K ASKEY 1456VQH76D(INT) FX.14501.
Picture Chapter 6 Part Name Part Number USB KB(GRAY), KU0355, US VER., 104KEYS KB.KUS03.026 USB KB(GRAY), KU0355, T.CHINESE VER., 104KEYS KB.KUS03.027 USB KB(GRAY), KU0355, INT'L US VER., 104 KEYS KB.KUS03.028 USB KB (GRAY), KU0355, ARABIC VER., 104 KEYS KB.KUS03.029 USB KB (GRAY), KU0355, THAI VER., 104 KEYS KB.KUS03.030 USB KB (GRAY), KU0355, GERMANY VER., 105 KEYS KB.KUS03.031 USB KB (GRAY), KU0355, ITALIAN VER., 105 KEYS KB.KUS03.032 USB KB (GRAY), KU0355, FRENCH VER., 105 KEYS KB.
Picture Part Name Part Number USB KEYBOARD, KU0355, SPANISH/US VER., 105KEYS KB.KUS03.008 USB KEYBOARD, KU0355, CANADIAN/FRENCH VER., 105KEYS KB.KUS03.009 USB KEYBOARD, KU0355, BRAZILIAN VER., 107KEYS KB.KUS03.010 USB KEYBOARD, KU0355, SWISS VER., 105KEYS KB.KUS03.011 USB KEYBOARD, KU0355, BELGIUM VER., 105KEYS KB.KUS03.012 USB KEYBOARD, KU0355, ICELAND VER., 105KEYS KB.KUS03.014 USB KEYBOARD, KU0355, NORWEGIAN VER., 105KEYS KB.KUS03.015 USB KEYBOARD, KU0355, HEBREW VER., 105KEYS KB.KUS03.
Picture Part Name Part Number For VT3600 LEFT COVER 60.V02VF.301 FRONT BEZEL W/ ODD DOOR, FDD COVER, FDD BUTTON 60.V02VF.302 ODD DOOR W BUTTON 42.V02VF.301 FDD BUTTON 42.V02VF.302 FDD COVER W LENS 42.V02VF.303 UPPER COVER 60.V02VF.303 RETENTION MODULE W NAIL 4PCS 42.V02VF.304 IO BRACKET HOLDER 42.V02VF.305 CHASSIS W IO BRACKET, DB BRACKET, LED BRACKET WO IO SHIELD 60.V02VF.004 IO SHIELD TBD FDD HOLDER 33.V02VF.301 ODD HOLDER (DISGUISE) 33.V02VF.302 HDD HOLDER ASSY(LEFT) 42.V02VF.
Picture Part Name Part Number Speaker INTERNAL SPEAKER 38MM NEOSONIC SP.CRB04.001 SPEAKER 5W+5W ACTIVE 12V PHILIPS A201S SP.20101.001 SYSTEM FAN W AIR DUCK TBD HEATSINK W LATCH HI.V020B.005 HEATSINK W LATCH HI.V020B.004 FOOT STAND (PLASTIC) 47.V02VF.301 SPS SCREW 86.RC9VF.001 MAIN BOARD SCREW 86.RC9VF.002 UPPER COVER SCREW 86.V02VF.301 SYSTEM FAN SCREW 86.V02VF.302 INTRUSION ALARM SCREW 86.V02VF.303 ODD DOOR SPRING 86.V02VF.304 THUMB SCREW 86.V02VF.
Chapter 6 120
Appendix A Model Definition and Configuration Veriton 7600GTR/7600GT/7600V, 5600GT/5600V, 3600GT/3600V 1. Project Name: Trumpet 2. Description Trumpet series is positioned to be the first Main Board product that supports the latest Intel® Chipset Springdale-G/GV technology with DDR DIMM module and Hyper-Threading Techology.
Appendix B Test Compatible Components This computer’s compatibility is a test plan released by Acer Internal Testing Department. Once the final report is available, this chapter will be revised accordingly.
Microsoft Windows XP Environment Test Item Specifications Processor Intel Celeron 2.4G / 2.5G / 2.6G / 2.7G / 2.8G Socket 478 Memory Infineon DDR 333 256MB 0.11u CL=2.5 Intel Northwood 2.4G / 2.6G / 2.8G / 3.0G / 3.06G D1 / 3.2G Socket 478 Infineon DDR400 128MB 0.14u 32M*8*16 CL=3 Infineon DDR400 256MB 0.14u 32M*8*16 CL=3 Infineon DDR400 512MB 0.14u 32M*8*16 CL=3 Nanya DDR 333 128MB 0.14u 16M*16 *4 Nanya DDR 333 256MB 0.14u CL2.5 Nanya DDR 333 512MB 0.14u CL2.
Item VGA Card Specifications FIC Radeon 9200 64MB DDR LP W/TV-OUT NTSC/ATX bracket FIC Radeon 9200 64MB DDR LP W/TV-OUT PAL,ATX bracket MSI Ti-4200-8X 128M DDR ATX w/TV-out (PAL), ATX bracket MSI Ti-4200-8X 128M DDR ATX w/TV-out (NTSC), ATX bracket MX 440 (8X) 64M DDR LP w/TV-out (PAL), ATX bracket (w/LP BKT) MX 440 (8X) 64M DDR LP w/TV-out (NTSC), ATX bracket (w/LP BKT) VGA, ECS Xabre200 AGP 8X 32M ATX Bracket DVI adapter card Leadtek DVI Adapter Card for 845G chipset on-die VGA Speaker Charming Stand
Item Keyboard (USB) Specifications Chicony Swiss, USB KB (acer 002), KUP0355, 105 keys, w/palm Chicony US ver., USB KB (acer 002), KUP0355, 104 keys, w/palm Chicony T. Chinese ver.
Appendix C Online Support Information This section describes online technical support services available to help you repair your Acer Systems. If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
127 Appendix C
