Acer Altos G530 Series User’s Guide
Copyright © 2005 Acer Incorporated All Rights Reserved. Acer Altos G530 Series User’s Guide Changes may be made periodically to the information in this publication without obligation to notify any person of such revision or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications.
iii Notices FCC notice Class A devices do not have an FCC logo or FCC IDE on the label. Class B devices have an FCC logo or FCC IDE on the label. Once the class of the device is determined, refer to the following corresponding statement. Class A equipment This device has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules.
iv Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. Notice: Peripheral devices Only peripherals (input/output devices, terminals, printers, etc.) certified to comply with the Class A or Class B limits may be attached to this equipment. Operation with noncertified peripherals is likely to result in interference to radio and TV reception.
v Important safety instructions Read these instructions carefully. Save these instructions for future reference. 1 Follow all warnings and instructions marked on the product. 2 Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 3 Do not use this product near water. 4 Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.
vi d If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition. e If the product has been dropped or the cabinet has been damaged f If the product exhibits a distinct change in performance, indicating a need for service.
iii iii iv v 1 System tour 1 Features summary External and internal structure Front bezel Front panel Rear panel Internal components System boards Mainboard layout Backplane board layout 2 System setup Setting up the system Pre-installation requirements Connecting peripherals Turning on the system Power-on problems Configuring the system OS Server setup Turning off the system 3 System upgrade Installation precautions ESD precautions Pre-installation instructions Post-installation instructions Opening t
viii Installing an additional hard disk into the HDD cage carrier Replacing the CD-ROM drive Installing 5.
ix 5 Troubleshooting Resetting the system Problems following initial system installation First steps checklist Hardware diagnostic testing Verifying proper operation of key system lights Confirming loading of the OS Specific problems and corrective actions BIOS error messages POST error messages POST beep codes Troubleshooting BIOS beep codes Appendix A: System management utility ASM 121 123 124 125 126 126 127 127 132 137 141 142 143 System requirements System setup RAID configuration SCSI RAID config
x Index 179
1 System tour
The Acer Altos G530 server is a powerful dualprocessor system loaded with a host of new and innovative features. The system offers a new standard for flexible productivity ideal for multimedia processing, intensive graphics applications, general business applications, email, web service, file clustering and print services.
3 Features summary Listed below are the system’s key features: Processor • Single or Dual Intel® Xeon™ processors with 1MB or 2MB L2 cache and 800 MHz front system bus • Supports Intel® Hyper-Threading Technology • Supports Intel® EM64T (Extended Memory 64 technology) Chipset • North bridge: Intel E7320 MCH (Memory Controller Hub) • South bridge: Intel 6300ESB ICH I/O controller Memory • Supports up to four DIMM sockets for a maximum memory capacity of 8 GB • Supports 512 MB, 1GB and 2GB DDR2
4 1 System tour Optional media storage • • Hot-plug HDD cage • Supports up to four 80-pin Ultra320 SCSI hard disk drives • Supports up to four SATA 150/300 hard disk drives Easy-swap HDD cage • Supports up to four 68-pin SCSI hard disk drives • Supports up to four SATA 150/300 hard disk drives Note: The main difference between a hot-plug HDD cage and an easy-swap HDD cage is the presence of a backplane board on the rear side of the hot-plug HDD cage.
5 Graphic interface • ATI Rage® XL chipset with 8MB SDRAM I/O ports • Front panel • Rear panel • Two USB 2.0 ports • PS/2 keyboard and mouse port • Two USB 2.0 ports • VGA/monitor port • Serial port • Two LAN ports (RJ-45) Operating system and software • Microsoft® Windows® Server 2003, X64 edition • Microsoft Windows Server 2003 • Microsoft Windows 2000 Server (SP4) • Novell® NetWare® 6.5 • Red Hat Enterprise Linux 3.0, EMT 64 • Red Hat Enterprise Linux 3.
6 1 System tour External and internal structure Front bezel No.
7 Front panel No. Icon Component Description 1 DVD/CD-ROM drive Stop/Eject button Press this button to open the CD drive tray. 2 DVD/CD-ROM drive activity indicator When the LED indicator is lit, there is activity in the CD drive. 3 DVD/CD-ROM drive Disk drive for reading CD-ROMs. 4 Volume control Adjusts the volume of the CD drive. 5 DVD/CD-ROM drive Headphone/ Earphone port Connects to microphones or earphones. 6 5.25-inch drive bays Two empty 5.
8 1 System tour No. 8 Icon Component Description Hard disk activity Indicates the status of the system hard drive. indicator 2 9 LAN activity indicator 3 LAN activity 10 Indicates an active link on the LAN1 port (green). indicator 4 Indicates an active link on the LAN2 port (green). Hot-plug HDD power Indicates drive activity (green). indicator 5 11 Four-bay hot-plug HDD cage Houses four hot-plug or easy swap SCSI/SATA drives. 12 HDD cage bay For additional storage options.
9 Front panel LED indicators Below table lists the LED states on the front panel. LED Color Status Description Power Green On Power on Blinking System in ACPI sleep mode. Blinking HDD activity Off No HDD activity On Network is established. HDD LAN1 and 2 Green Green Blinking • Network activity. • Network is established and running at its supported speed. Off Network link is not established. Hot-plug HDD LED indicators Below table lists the possible disk drive status.
10 1 System tour Rear panel No. Icon Component Description 1 Power supply module bay Allows installation of a redundant and non-redundant redundant power supply module. The hot-swap redundant power supply module may include three LEDs that will indicate its operating status. Note: If the system comes bundled with only a single redundant power supply module, you have the option to separately purchase an extra power supply module to provide the system with redundant power source.
11 No. Icon Component Description 4 PS/2 keyboard port Connects to a PS/2 keyboard. 5 VGA/monitor port Connects to monitors. 6 Serial port Connects to serial devices. 7 Gigabit LAN ports (10/100/ 1000 Mbps) Connects to network cables. 8 Expansion slots For installing expansion cards. 9 PCI slot lock lever Secures the PCI card to the system. 10 Rear system fan Optimizes system airflow.
12 1 System tour Rear panel LED indicators Below table lists the LED states on the LAN port. LED Green Yellow Status Link On — • Indicates 100MBps Ethernet operation. • Network link is established. Blinking — Indicates transmission or reception of data in the network. Off — • Indicates 10 MBps Ethernet operation. • Network link is not established. • The LAN cable is not working. Activity — On Indicates 1000 MBps Ethernet operation. — Off Network is idle.
13 Internal components No. Component 1 Power supply module (600 or 610-watts) 1 2 Rear system fan 3 Mainboard, CPU and heat sink fan assembly 4 PCI bus slot 5 Four-bay hot-plug HDD cage 1 The system supports a redundant or non-redundant power supply module. If the system comes bundled with a single 610-w redundant power supply module, you have the option to purchase an extra power supply module to provide the system with a redundant power source.
14 1 System tour System boards Mainboard layout The mainboard becomes accessible once you open the system. It should look like the figure shown below.
15 No.
16 1 System tour No.
17 Jumper settings J17 jumper The J17 jumper provides a total of 3-pin blocks that are used to configure several system recovery and update options. The table below lists each jumper option Pin no.
18 1 System tour The following below lists the pin-out of the J38 header. Pin no. Signal name Pin no.
19 Backplane board layout The backplane board attached to the four-bay hot-plug HDD cage provides a convenient interface between the SCSI or SATA drives and the mainboard. SCSI backplane board layout Rear Front No.
20 1 System tour No.
21 SATA backplane board layout Rear Front No. Code Description 1 SATA HDD connectors 2 SAF-TE heartbeat LED and Manufacturing function jumper 3 JP2 Debug connector 4 J1 Backplane no.
22 1 System tour No.
2 System setup
This chapter gives you instructions on how to set up the system. Procedures on how to connect peripherals are also explained.
25 Setting up the system Pre-installation requirements Selecting a site Before unpacking and installing the system, select a suitable site for the system for maximum efficiency.
26 2 System setup Connecting peripherals Refer to the illustration below for specific connection instructions on the peripherals you want to connect to the system. Note: Consult the operating system manual for information on how to configure the network setup.
27 Turning on the system After making sure that you have properly set up the system and connected all the required cables, you can now power on the system. To power on the system: 1 Open the bezel door. 2 Press the power button.
28 2 System setup The system starts up and displays a welcome message on the monitor. After that, a series of power-on self-test (POST) messages appears. The POST messages indicate if the system is running well or not. Note: If the system does not turn on or boot after pressing the power button, go to the next section for the possible causes of the boot failure.
29 Power-on problems If the system does not boot after you have applied power, check the following factors that might have caused the boot failure. • The external power cable may be loosely connected. Check the power cable connection from the power source to the power cable socket on the rear panel. Make sure that the cable is properly connected to the power source and to the power cable socket. • No power comes from the grounded power outlet. Have an electrician check your power outlet.
30 2 System setup Configuring the system OS The Altos G530 comes with Acer EasyBUILDTM that allows you to conveniently install your choice of operating system. To start using EasyBUILD, follow the steps below. 1 Locate the EasyBUILD System CD included in the system package. 2 With the system turned on, gently press the CD-ROM drive Stop/ Eject button. 3 When the disc tray slides open, insert the EasyBUILD System CD with the label or title side of the disc facing upward.
31 Server setup Aside from its tower configuration, the Altos G530 server system can also be mounted in a rack-model position. A rack mount kit is available for customers who want to convert a tower-mounted system to rackmodel design. To purchase a rack mount kit, contact your local Acer representative or order directly from http://www.acer.com/. The figure below shows the Altos G530 server in a rack-mount position.
32 2 System setup Turning off the system There are two ways by which you can turn off the server. These include: To turn off the server, on the Windows taskbar click on the Start button, point to Shut Down..., select Shut down from the drop-down window then click on OK. You can then turn off all peripherals connected to your server. If you cannot shut down the server, press the power button for at least four seconds. Quickly pressing the button may put the server in a Suspend mode only.
3 System upgrade
This chapter discusses the precautionary measures and installation procedures you need to know when upgrading the system.
35 Installation precautions Before you install any server component, we recommend that you read the following sections. These sections contain important ESD precautions along with pre-installation and post-installation instructions. ESD precautions Electrostatic discharge (ESD) can damage the processor, disk drives, expansion boards, motherboard, memory modules and other server components.
36 3 System upgrade Warning! Failure to properly turn off the server before you start installing components may cause serious damage. Do not attempt the procedures described in the following sections unless you are a qualified service technician. Post-installation instructions Perform the steps below after installing a server component: 1 See to it that all components are installed according to the described step-by-step instructions.
37 Opening the server Caution! Before you proceed, make sure that you have turned off the system and all peripherals connected to it. Read the “Preinstallation instructions” on page 35. You need to open the server before you can install additional components. The front bezel and left-side panel are removable to allow access to the system’s internal components. Refer to the following sections for instructions.
38 3 System upgrade Opening the bezel door A security lock secures the bezel door to protect the system unit from unauthorized access. To open the bezel door: 1 Insert the key into the lock and turn it clockwise until it points to the unlock icon . 2 Pull open the bezel door. Removing the front bezel 1 Remove the left-side panel. See page 37. 2 Slightly bend the plastic retention tabs to release the latches (1). 3 Gently detach the bezel from the chassis (2).
39 Removing the HDD cage bay cover 1 Open the bezel door. 2 Push down the HDD cage bay cover (1). 3 Detach the HDD cage bay cover from the front bezel (2).
40 3 System upgrade Configuring the four-bay HDD cage This section explains how to install a four-bay hot-plug HDD cage as well as procedures on how to install a hard disk into the cage’s hard disk carrier.
41 To install the hot-plug SCSI HDD cage: 1 Observe the ESD precautions and pre-installation instructions described on page 35. 2 Remove the HDD cage bay cover. See page 39. 3 Remove the screw that secures the cover to the empty HDD bay (1), then detach the cover (2). 4 Install the hot-plug cage.
42 3 System upgrade (1) Slide the cage into the chassis with the backplane board facing the rear of the chassis. The cage is locked to the chassis with an audible click. (2) Locate and attach the following cables clamped on the side of the chassis to their corresponding connectors on the backplane board: Important: If a four-bay hot-plug SCSI HDD cage is already installed in the top HDD bay, you must block the W83792D_ID1 jumper. Set pins 2 and 3 to short.
43 (2) SCSI HDD power cables 5 Observe the post-installation instructions described on page 36. Important: When you are detaching the hot-plug HDD cage from the chassis, make sure to first remove all hard disks from their carriers. For instructions, see “Installing an additional hard disk into the HDD cage carrier” on page 53. 6 Change the RAID configuration of your hard disk. For details on how to change the RAID configuration of your hard disk, go to “Appendix D: SCSI RAID configuration” on page 173.
44 3 System upgrade To install the easy-swap SCSI HDD cage: The easy-swap SCSI HDD cage is an optional four-bay internal HDD enclosure without a SCSI backplane board. 1 Observe the ESD precautions and pre-installation instructions described on page 35. 2 Remove the HDD cage bay cover. See page 39. 3 Remove the screw that secures the cover to the empty HDD bay, then detach the cover. 4 Install the easy-swap cage. (1) Slide the cage into the chassis.
45 (2) SCSI HDD power cables 5 Observe the post-installation instructions described on page 36. Important: When you are detaching the easy-swap cage from the chassis, make sure to first remove all cables attached to the hard disks. 6 Change the RAID configuration of your hard disk. For details on how to change the RAID configuration of your hard disk, go to “Appendix D: SCSI RAID configuration” on page 173.
46 3 System upgrade To install the hot-plug SATA HDD cage: 1 Observe the ESD precautions and pre-installation instructions described on page 35. 2 Remove the HDD cage bay cover. See page 39. 3 Remove the screw that secure the cover of the empty HDD bay, then detach the cover.
47 4 Install the hot-plug cage. (1) Slide the cage into the chassis. The cage is locked to the chassis with an audible click. 5 Connect the following cables to their corresponding connectors on the SATA RAID backplane board, mainboard and adapter: Important: If a four-bay hot-plug SATA HDD cage is already installed in the top HDD bay, you must block the J1 jumper. Set pins 2 and 3 to short.
48 3 System upgrade (2) Attach the system’s power cable to the SATA power cable connector on the backplane board (2). Note: The SATA RAID data cables must be installed and removed in the following order: SATA0, SATA1, SATA2, then SATA3. 6 Observe the post-installation instructions described on page 36. Important: When you are removing the hot-plug cage from the chassis, make sure to first remove all hard disks from their carriers.
49 To install the easy-swap SATA HDD cage: The easy-swap SATA HDD cage is an optional four-bay internal HDD enclosure without a SATA backplane board. 1 Observe the ESD precautions and pre-installation instructions described on page 35. 2 Remove the HDD cage bay cover. See page 39. 3 Remove the screw that secures the cover to the empty HDD bay, then detach the cover. 4 Install the easy-swap cage.
50 3 System upgrade (1) Slide the cage into the chassis. The cage is locked to the chassis with an audible click. (2) Locate and attach the power (1) and SATA (2) cables to their corresponding connectors on the hard drives and SATA RAID card. 5 Observe the post-installation instructions described on page 36.
51 Important: When you are removing the easy-swap cage from the chassis, make sure to first remove all cables attached to the hard disks. 6 Change the RAID configuration of your hard disk. For details on how to change the RAID configuration of your hard disk, go to “Appendix C: SATA RAID configuration” on page 167.
52 3 System upgrade Removing the four-bay HDD cage 1 Observe the ESD precautions and pre-installation instructions described on page 35. 2 Disconnect the data and power cables from the backplane board. 3 Move the release slider all the way up to eject the hot-plug or easy swap HDD cage (1). 4 Remove the cage from the HDD bay (2). 5 Observe the post-installation instructions described on page 36.
53 Installing an additional hard disk into the HDD cage carrier Note: To purchase a hard disk carrier, contact your local Acer representative. Important: You need not remove the four-bay hot-plug HDD cage from the chassis to install a hard disk into its carrier. 1 Carefully pull out the hard disk carrier cover (1).
54 3 System upgrade 2 Install a hard disk on the hard disk carrier (1), then secure it with the four screws that came with the hard disk carrier (2). 3 Insert the new hard disk carrier into the cage with the lever still extended (1). 4 Make sure that the drive is properly inserted before closing the lever, then push the lever back until it clicks into place (2). .
55 Replacing the CD-ROM drive 1 Observe the ESD precautions and pre-installation instructions described on page 35. 2 Disconnect the power and IDE cables from the old drive. 3 Push the lever in the direction of the unlock icon the drive out of the chassis (2).
56 3 System upgrade 4 Install a new 5.25-inch drive into the drive bay (1), then push the lever in the direction of the lock icon (2). 5 Connect the power and IDE cables to the new drive. 6 Observe the post-installation instructions described on page 36.
57 Installing 5.25-inch drives The two empty 5.25-inch drive bays allow you to install additional drives such as another backup hard drive, CD-ROM drive, or a tape drive. These options provide the system with additional storage capacity. To install a 5.25-inch tape drive: 1 Observe the ESD precautions and pre-installation instructions described on page 35. 2 Remove the two screws that secure the cover to the empty 5.25-inch drive bay (1), then detach the cover (2).
58 3 System upgrade 3 Install a tape drive into the drive bay (1), then push the lever in the direction of the lock icon (2). 4 Connect the power and IDE cables to the tape drive. 5 Observe the post-installation instructions described on page 36.
59 Upgrading the processor This section includes instructions for installing and removing a processor and heat sink fan (HSF) assembly. Installing the CPU The mainboard has two 604-pin processor socket that support Intel Xeon processors. The system ships out with only a single Intel Xeon processor installed leaving one CPU socket empty. You have the option to purchase an extra CPU for the system.
60 6 3 System upgrade Press the retainer lever down to lock the CPU in place (2). Installing the HSF assembly 1 Apply thermal grease. Apply approximately 0.1ml of the thermal grease compound on it’s top side.
61 (1) Align the heat sink fan assembly to the CPU (1). (2) Using a screwdriver, tighten the heatsink’s four screws to secure it to the mainboard (2). (3) Connect the CPU fan cable to its mainboard connector. Refer to “Mainboard layout” on page 14 for the location of the CPU fan connector. 3 Observe the post-installation instructions described on page 36. Removing the HSF assembly Important: Before removing a CPU from the mainboard, make sure to create a backup file of all important data.
62 3 System upgrade 2 Disconnect the CPU fan cable from its mainboard connector. 3 Loosen the four screws that hold the HSF assembly to the mainboard (1). 4 Pull the HSF assembly away from the CPU (2). 5 Place the HSF assembly upside down on a flat surface. Note: Wipe off the thermal grease from both the HSF assembly and CPU using an alcohol pad.
63 Removing the CPU 1 Pull the CPU socket retainer lever to a fully open, upright position (1). 2 Pull out the CPU from the socket (2).
64 3 System upgrade Upgrading the system memory This section includes instructions for removing and installing a memory module. Altos G530 has four DDR2-400 DIMM slots. Each slot supports 512 MB, 1GB or 2GB memory modules. The maximum memory capacity is 8GB. Memory module installation guidelines • The minimum memory configuration is one DIMM, installed in the DIMM 1B socket (the socket farthest from the CPU sockets).
65 • Both DIMMs in a bank must be identical (same manufacturer, CAS latency, number of rows, columns and devices, timing parameters, etc.). Although DIMMs within a bank must be identical, the BIOS supports various DIMM sizes and configurations allowing the banks of memory to be different. Warning! For the system to function, DIMM modules must be installed or removed in matched pairs, following the socket sequence : DIMM 1B and 1A first, then DIMM 2B and 2A.
66 3 System upgrade Altos G530 supports memory sparing function. To provide a more fault tolerant system, Altos G530 includes special hardware to support failover to a spare DIMM device in the event that a primary DIMM in use exceeds a specified threshold of runtime errors. One of the DIMMs installed per channel will not be used, but kept in reserve.
67 Removing a DIMM Before you can install a new DIMM in a socket, remove first any previously installed DIMM from that socket. Important: Before removing any DIMM from the mainboard, make sure to create a backup file of all important data. 1 Observe the ESD precautions and pre-installation instructions described on page 35. 2 Locate the DIMM sockets on the mainboard. 3 Press the holding clips on both sides of the socket outward to release the DIMM.
68 3 System upgrade Installing a DIMM 1 Observe the ESD precautions and pre-installation instructions described on page 35. 2 Locate the DIMM sockets on the mainboard. Note: DIMM modules must be installed in matched pairs, following the socket sequence: DIMM 1B and 1A first, then DIMM 2B and 2A. 3 Open the clips on the socket. 4 Align then insert the DIMM into the socket. 5 Press the holding clips inward to lock the DIMM in place. Note: The DIMM socket is slotted to ensure proper installation.
69 To reconfigure the system memory: The system automatically detects the amount of memory installed. Run the BIOS setup to view the new value for total system memory and make a note of it.
70 3 System upgrade Installing an expansion card This section explains how to install an expansion card. The onboard expansion slots supports PCI (Peripheral Component Interconnect), PCI-X, and PCI Express cards. PCI Express slot is a new type of interface and differs in length than the conventional PCI/PCI-X slots. You should always install the correct type of plug-in expansion cards in the x4 PCI Express slot. Contact your dealer for qualified PCI Express card vendors.
71 8 Press the PCI slot release latch on the rear panel of the server (4). 9 Observe the post-installation instructions described on page 36. Note: When you turn on the system, the BIOS setup automatically detects and assigns resources to the new device (applicable only to plug-and-play expansion cards).
72 3 System upgrade Upgrading the power supply The Altos G530 system may ship out with a redundant or nonredundant power supply module. Installing a redundant power supply module The Altos G530 power subsystem consists of two redundant power supply module bays that accept 610-watt hot-swap redundant power supply modules. The system ships out with only a single power supply module leaving one power supply module bay empty.
73 1 Remove the cover of the empty power supply module bay. Note: If the system ships out with a screw on the cover, remove the screw first then detach the cover.
74 3 System upgrade 2 Hold the handle on front of the power supply module while pressing your thumb on the release latch. Slide the power supply module into the empty bay until you feel resistance. 3 Press the module handle to secure the power supply module to its bay. 4 Verify that the power indicators on the main power supply and on the newly installed redundant power supply are illuminated green.
75 Installing a non-redundant power supply module The Altos G530 power subsystem accepts a 600-watt non-redundant power supply module. If you are replacing a previously installed power supply module, turn it off and unplug it. 1 Observe the ESD precautions and pre-installation instructions described on page 35. 2 Detach the power and power supply cable from their connectors. 3 Remove the four screws on the cover of the power supply module bay, then detach the cover.
76 3 System upgrade 5 Slide the new power supply module into the bay, then secure it to the chassis with the four screws removed earlier. 6 Attach the power cable to the power cable socket. 7 Attach the power supply cable to the mainboard connector. Note: If a four-bay hot-plug HDD cage is already installed in your chassis, attach the power cable to the hard drive’s power cable connector. 8 Observe the post-installation instructions described on page 36.
4 BIOS setup
This chapter gives information about the system BIOS and discusses how to configure the system by changing the settings of the BIOS parameters.
79 BIOS setup BIOS setup is a hardware configuration program built into the system's Basic Input/Output System (BIOS). Since most systems are already properly configured and optimized, there is no need to run this utility.
80 4 BIOS setup Entering BIOS setup Power on the server to start the system POST process. During bootup, press F2 to enter the BIOS setup screen. Note: You must press F2 while the system is booting. This key does not work during any other time. There are several tabs on the setup screen corresponding to the six major BIOS menus: • Main • Advanced • Boot • Security • Server • Exit The parameters on the screens shown in this User’s Guide display default system values.
81 • Press F1 for General Help on using the BIOS setup. • Press F10 to save changes and close the BIOS setup. • Press Esc to close the BIOS setup. In the descriptive table following each of the screen illustrations, settings in boldface are the default and suggested parameter settings. Note: The BIOS screens shown in the following pages may vary depending on the system configuration.
82 4 BIOS setup Main The Main menu displays basic and important information about the system. These information are necessary for troubleshooting and may be required when asking for technical support. These entries are for your reference only and are not user-configurable. The last two parameters on the screen lets you define the sytem’s time and date settings. The real-time clock keeps the system date and time.
83 Parameter Description Processor Speed The processor speed is the speed at which a microprocessor executes instructions. Clock speeds are expressed in megahertz (MHz), with 1 MHz being equal to 1 million cycles per second. The faster the clock, the more instructions the CPU can execute per second. Processor Count Indicates the number of processors currently installed in the server. System Memory Size Indicates the total amount of onboard memory.
84 4 BIOS setup Advanced The Advanced menu contains parameter values that define how the system behaves on startup. Warning! Be cautious in setting parameter values in the Advanced menu as any incorrect value may cause the system to malfunction. Press Enter to enter the submenu screen of the parameters shown in the screen below.
85 Processor Configuration The Processor Configuration submenu displays CPU settings such as type, actual speed, cache size and other CPU related settings. Parameter Description Manufacturer Processor manufacturer Brand String Processor brand identification number Frequency Indicates the calculated processor speed. FSB Speed Indicates the processor front side bus speed. CPU 1 CPUID ID number of CPU 1. CPU 1 Cache L1 Indicates CPU 1 cache L1 size. CPU 1 Cache L2 Indicates CPU1 cache L2 size.
86 4 BIOS setup Parameter Description Option CPU 2 CPUID ID number of the CPU 2. CPU 2 Cache L1 Indicates CPU 2 cache L1 size. CPU 2 Cache L2 Indicates CPU 2 cache L2 size. Max CPUID Value Limit Enable to boot legacy operating systems. Disabled Execute Disable Bit When Enabled, the processor disables code execution when a worm attempts to insert a code in the buffer, preventing damage and worm propagation.
87 Parameter Description Option HT Technology in MPS When Enabled, adds secondary processor threads to the MPS (multiprocessor) table for the pre-ACPI (pre- Advanced Configuration and Power Interface) operating systems. Disabled Enabled Intel SpeedStep® Technology When set to Auto, this feature allows the operating system to reduce power consumption. Disabled When set to Disabled, the system operates at maximum CPU speed.
88 4 BIOS setup IDE Configuration The IDE Configuration submenu lets you define the parameter settings related to the hard disk/s. Parameter Description Option Onboard P-ATA Channels When set to Both, the system can support both Primary and Secondary PATA Controllers. Both When set to Disabled, it disables the integrated PATA Controller. Secondary Disabled Primary When set to Primary, it enables support for Primary PATA Controller.
89 Parameter Description Option Configure S-ATA as RAID When set to Enabled, the SATA channels are reserved to be used as RAID. Disabled Enabled S-ATA Ports Definition Defines priority between SATA channels. A 1-3rd M/A 2-4th M A 1-4th M/ A 2-3rd M Mixed P-ATA/ S-ATA Lets you remove a PATA and replace it by SATA in a given channel. Only one channel can be designated as SATA. Press Enter to access the Mixed PATA/ SATA submenu.
90 4 BIOS setup Parameter Description Fourth IDE Master Specifies the current configuration of the IDE device connected to the master port of the fourth IDE channel. Press Enter to access the Fourth Master submenu. Hard Disk Write Protect Enables or disables write protection to system hard drives. Disabled IDE Detect Time Out (Sec) Select the time out value for detecting ATA/ATAPI devices. 0 Used with older IDE devices with longer spin up times.
91 Mixed P-ATA / S-ATA The Mixed P-ATA/S-ATA submenu lets you specify the channel for the Parallel ATA Primary channel and Serial ATA device. Parameter Description Option First/Second ATA Channel Select channel mode. P-ATA M-S 3rd/4th ATA Channel Select channel mode.
92 4 BIOS setup Primary/Secondary/Third/Fourth IDE Master/Slave These items let you select the IDE hard disk parameters that the system supports. Parameter Description Device Type of IDE device. Vendor Vendor of the selected IDE device. Size Capacity of the selected IDE device. LBA Mode LBA mode of the selected IDE device. Block Mode Block mode of the selected IDE device. PIO Mode PIO mode of the selected IDE device. Async DMA Async DMA mode of the selected IDE device.
93 Parameter Description S.M.A.R.T. Indicates if the selected device supports S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) function. Type Selects the drive type. Option Auto Not Installed CD-ROM ARMD LBA/Large Mode Selects the hard disk drive translation method. For drivers with more than 504 MB, LBA mode is necessary. Auto Disabled Block (Multi-Sector Transfer) Mode Enhances disk performance depending on the hard disk in use.
94 4 BIOS setup Parameter Description Option DMA Mode Selects DMA (Direct Memory Access) mode. Auto SWDMA0 SWDMA1 SWDMA2 MWDMA0 MWDMA1 MWDMA2 UDMA0 UDMA1 UDMA2 UDMA3 UDMA4 UDMA5 S.M.A.R.T. 32Bit Data Transfer Enables or disables the S.M.A.R.T. function of the internal hard disk. When set to Auto, the BIOS setup will enable the S.M.A.R.T. function if the drive supports it. Auto Enables or disables the 32-bit data transfer function.
95 Floppy Configuration The Floppy Configuration submenu displays the type of floppy drive installed in the server. Parameter Description Option Floppy A Floppy disk drive type. 1.44 MB 3 1/2” 2.88 MB 3 1/2” 720 KB 3 1/2” Disabled Onboard Floppy Controller Allows BIOS to enable or disable the floppy controller.
96 4 BIOS setup Super I/O Configuration The Super I/O Configuration submenu lets you define the parameter settings for the system’s serial port. Parameter Description Option Serial Port A Indicates the serial port 1 address and IRQ setting. 3F8/IRQ4 Disabled 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Serial Port B Indicates the serial port 2 address and IRQ setting.
97 USB Configuration The USB Configuration submenu lets you specify settings for USB devices. Parameter Description Option USB Function Enables or disables the UBS host controller. Enabled Disabled When set to Disabled, other USB options will be grayed out. Legacy USB Support Enables or disables the support for legacy USB devices. When set to Auto, the system detects the presence of USB devices at startup. If a USB device is detected, the USB controller legacy mode will be enabled.
98 4 BIOS setup Parameter Description Option USB 2.0 Controller Enables the USB 2.0 controller. Enabled Disabled USB 2.0 Controller Mode Sets the transfer rate at HiSpeed (480 Mbps) or FullSpeed (12 MBps). HiSpeed USB Mass Storage Device Configuration Lets you specify the settings of the USB mass storage class devices. Press Enter to access the USB Mass Storage Device Configuration submenu.
99 PCI Configuration The PCI Configuration submenu lets you specify settings that are related to the onboard controllers. Parameter Description Option Onboard Video Enables or disables the onboard VGA controller. Enabled Dual Monitor Video Select a graphic controller as a primary boot device. Note: This parameter will be grayed out when the Onboard Video is set to Disabled. Disabled Enabled Onboard NIC1 (Left) Enables or disables the onboard NIC1 (Gigabit network interface controller).
100 4 BIOS setup Parameter Description Option Onboard NIC 2 (Right) Enables or disables the onboard NIC2 (10Base-T/ 100Base/ 1000 Base network interface controller). Enabled Disabled Onboard NIC2 ROM Enables or disables the onboard NIC2 ROM. Enabled Disabled Onboard SCSI Enables or disables the onboard SCSI ontroller. Enabled Disabled Onboard SCSI ROM Enables or disables the onboard SCSI ROM. Enabled Onboard SCSI Mode Select a SCSI mode.
101 Memory Configuration The Memory Configuration submenu provides information about the DIMMs installed in DIMM slots 1A, 1B, 2A, and 2B. Parameter Description Option DIMM 1A, 1B, 2A and 2B Indicates the current memory status. Installed Not Installed Disabled Spare Extended Memory Test Settings for extended memory test.
102 4 BIOS setup Parameter Description Option Memory Retest When Enabled, BIOS will activate and retest all DIMMs on next boot. Note: This parameter will automatically reset to Disabled. Disabled Enabled Memory Remap Feature Enables or disables remapping of overlapped PCI memory above the physical memory. Enabled Memory Sparing When set to Spare, a DIMM slot is kept in reserve for standby in the event a significant failure occurs in the primary DIMM.
103 Boot The Boot menu allows you to set the drive priority during system bootup. It also displays information about the installed storage devices. Press Enter to enter the submenu screen of the parameters shown in the screen below.
104 4 BIOS setup Boot Settings Configuration The Boot Settings Configuration submenu lets you specify the preferred settings for system bootup. Parameter Description Option Quick Boot Allows the system to boot faster by skipping some POST routine. Enabled Enables or disables the Quiet Boot function. Disabled Quiet Boot When set to Enabled, BIOS setup is in graphical mode and displays only an identification logo during POST and while booting.
105 Parameter Description Option Bootup Num-Lock Activates the Numeric Lock function upon booting. Off On PS/2 Mouse Support Enable this parameter if you intend to use a mouse or trackball with a PS/2 interface. Auto POST Error Pause When this parameter is Enabled, you will be prompted when an error is detected during boot up. When set to Disabled, the system will boot with no intervention, if possible.
106 4 BIOS setup Boot Device Priority The Boot Device Priority submenu lets you specify the boot search sequence during the POST process. BIOS setup will display an error message if the drive(s) specified is not bootable. Parameter Description 1st Boot Device Sets the device from which the system will first attempt to boot up. Press Enter to access the Removable Drives submenu. 2nd Boot Device Sets the device from which the system will attempt to boot up when the first attempt failed.
107 Parameter Description 4th and 5th Boot Device Sets the device from which the system will attempt to boot up when the first, second and third attempts failed. Hard Disk Drives The Hard Disk Drives submenu lets you specify the devices that will be considered as the primary and secondary hard drives.
108 4 BIOS setup Removable Drives The Removable Drives submenu displays the type of removable devices installed in the system.
109 CD/DVD Drives The CD/DVD Drives submenu displays the type of ATAPI CD-ROM installed in the system.
110 4 BIOS setup Security The Security menu allows you to safeguard and protect the system from unauthorized use by setting up access passwords. Parameter Description Option Administrator Password Prevents unauthorized access to the BIOS setup utility. Not Installed User Password Secures the system against unauthorized use. Once you set this password, you have to type it whenever you boot the system. User password is available only when a Supervisor password is set.
111 Parameter Description Option User Access Level When set to Full Access, allows access to any field in the BIOS setup utility. When set to No Access, user is not allowed to access the BIOS setup utility. Full Access No Access View Only Limited When set to View Only, allows access to the BIOS setup utility but fields cannot be changed. When set to Limited, allows access to Date and Time in the BIOS setup utility. Clear User Password Clears the User password.
112 4 BIOS setup Removing the User password 1 Use the up/down keys to highlight the Clear User Password parameter then press Enter. 2 Enter the current password then press Enter. 3 Press Enter twice without entering anything in the new and confirm password fields. After doing this, the system automatically sets the User password parameter to Not Installed.
113 Server The Server menu allows you to configure appropriate settings for monitoring the server. Parameter Description System Management Press Enter to access the System Management submenu. Serial Console Features Press Enter to access the Serial Console Features submenu. Event Log Configuration Press Enter to access the Event Log Configuration. Assert NMI on SERR Enables or disables the PCI bus SERR (system error) support.
114 4 BIOS setup Parameter Description Option Assert NMI on PERR Enables or disables the PCI bus PERR (parity error) support. Note: This parameter is disabled when the NMI on SERR is disabled. Enabled Disabled Resume on AC Power Loss Defines the mode of operation if a power loss occurs. Stays Off Power On When set to Stays Off, the system remains off after power shutdown. When set to Power On, the system will turn on after power is restored.
115 Serial Console Features The Serial Console Features submenu allows you to configure the serial port settings. Parameter Description Option BIOS Redirection Port Specify the serial port where a hardware console is connected. Disabled Baud Rate Selects the baud rate or transfer speed for console redirection. 19.2 K Serial A Serial B 9600 38.4 K 57.6 K 115.2 K Flow Control Selects a flow control for the system.
116 4 BIOS setup Parameter Description Option Terminal Type Specify the type of remote console. VT100+ VT-UTF8 PC-ANSI ACPI Redirection Port Specify the serial port where an ACPI (Advanced Configuration and Power Interface) console is connected.
117 Event Log Configuration The Event Log Configuration submenu allows you to record and monitor events that occur in the system (e.g. system temperature changes, fan stops, etc.). Parameter Description Option View Event Log Opens the system Event log file for viewing. Clear Event Log Discards all events in the Event log. BIOS Event Logging Enables or disables the event logging function of the sytem.
118 4 BIOS setup Parameter Description Option ECC Error Logging Enables or disables the ECC (Error Correcting Code) event logging function of the system. ECC tests the accuracy of data as it passes in and out of memory. When this parameter is enabled, single-bit and multi-bit memory errors will be recorded in the event log. Enabled Disabled PCI Error Logging Enables or disables the PCI error logging.
119 Exit The Exit menu displays the various options to quit from the BIOS setup utility. Highlight any of the exit options then press Enter. Parameter Description Save Changes and Exit Saves changes made and close the BIOS setup utility. The F10 key can also be used for this operation. Discard Changes and Exit Exits system setup without saving any changes. The Esc key can also be used for this operation. Discard Changes Discards changes made in the BIOS setup.
120 4 BIOS setup Parameter Description Load Setup Defaults Loads the default settings for all BIOS setup parameters. Setup Defaults are quite demanding in terms of resources consumption. If you are using low-speed memory chips or other kinds of low-performance components and you choose to load these settings, the system might not function properly. The F9 key can also be used for this operation. Load Custom Defaults Loads the custom settings for all BIOS setup parameters.
5 Troubleshooting
This chapter provides possible solutions for specific problems. If you cannot correct the problem, contact your local Acer representative or authorized dealer for assistance.
123 Resetting the system Before going through in-depth troubleshooting, attempt first to perform reset the system using one of the methods below. To do this Press Soft boot reset to clear the system memory and reload the operating system. Ctrl+Alt+Del Cold boot reset. Turn the system power off and then on. This clears system memory, restarts POST, reloads the operating system and halts power to all peripherals.
124 5 Troubleshooting Problems following initial system installation Problems that occur at initial system startup are usually caused by an incorrect installation or configuration. Hardware failure is a less frequent cause. If the problem you are experiencing is with a specific software application, see "There is problem with the application software" on page 130.
125 First steps checklist • AC power available at the wall outlet? • Are the power supplies plugged in? Check the AC cable(s) on the back of the chassis and at the AC source.
126 5 Troubleshooting Hardware diagnostic testing This section provides a more detailed approach to identifying a hardware problem and locating its source. Caution! Turn off devices before disconnecting cables: Before disconnecting any peripheral cables from the system, turn off the system and any external peripheral devices. Failure to do so can cause permanent damage to the system and/or the peripheral devices. 1 Turn off the system and all external peripheral devices.
127 Confirming loading of the OS Once the system boots up, the operating system prompt appears on the screen. The prompt varies according to the operating system. If the operating system prompt does not appear, see "No Characters Appear on Screen" on page 131. Specific problems and corrective actions The following contains specific problems that may arise during the use of your server. Possible solutions are listed for each problem. Power indicator does not light.
128 5 Troubleshooting • Make sure the FDD and signal cables are properly connected. • Check that relevant switches and jumpers for the FDD are set correctly. • Check that FDD is properly configured. • If you are using the onboard diskette controller, use BIOS setup on page 79 to make sure that onboard “Floppy A” is set to 1.44 MB, 3.5-inch. HDD activity indicator does not light. Do the following: • Make sure the drive is not disabled in the BIOS setup utility.
129 CD drive activity indicator does not light. Do the following: • Make sure the power and signal cables are properly installed. • Check that relevant switched and jumpers on the drive are set correctly. • Check that drive is properly configured. • Check that onboard IDE controller is enabled in the BIOS setup. CD tray cannot be ejected. Do the following: • Insert the tip of a paperclip into the small hole on the CD drive.
130 5 Troubleshooting Network status indicator does not light. Do the following: • Check the cabling and network equipment to make sure that all cables are properly connected. • Reinstall the network drivers. • Try another port or hub on the switch. Network activity indicator does not light. Do the following: • Make sure the correct network drivers are loaded on the system. • Network might be idle. Try accessing the server. Server hangs when the drivers are loaded.
131 No characters appear on the screen. Check the following: • Is the keyboard functioning? Test it by turning the “Num Lock” function on and off to make sure the Num Lock light is functioning.
132 5 Troubleshooting BIOS error messages When a recoverable error occurs during POST, BIOS will display an error message describing the problem. The following table defines the error messages that may be displayed if the system BIOS detects an error during POST. Error message Description Memory BIOS messages Gate20 error An error occurred with Gate A20 when switching to protected mode during the memory test.
133 Error message Description Storage device BIOS messages Primary Master/Slave Hard Disk Error Secondary Master/Slave Hard Disk Error Could not read sector from corresponding drive. 3rd Master/Slave Hard Disk Error 4th Master/Slave Hard Disk Error 5th Master/Slave Hard Disk Error 6th Master/Slave Hard Disk Error Primary Master/Slave Drive ATAPI Incompatible Secondary Master/Slave Drive - Corresponding drive is not an ATAPI device. Run Setup to make sure device is selected correctly.
134 Error message 5 Troubleshooting Description Virus related BIOS message BootSector Write !! A software attempting to write to a drive’s boot sector has been detected. This is flagged as possible virus activity. This message will only be displayed if Virus Detection is enabled in the BIOS setup. VIRUS: Continue (Y/N)? A possible virus activity is detected. This message will only be displayed if Virus Detection is enabled in the BIOS setup.
135 Error message Description Static Resource Conflict Two or more Static Devices are trying to use the same resource space (usually Memory or I/O). PCI I/O conflict PCI ROM conflict An I/O resource conflict was detected. PCI IRQ conflict PCI IRQ routing table error Unable to route an IRQ to the PCI device. Timer Error An error occurred while programming the count register of channel 2 of the 8254 timer. Interrupt Controller-1 error The Master Interrupt Controller could not be initialized.
136 5 Troubleshooting Error message Description Warning! EHCI controller disabled. It requires 64bit data support in the BIOS. The EHCI controller is disabled because of incorrect data structure. This condition occurs if the USB host controller needs 64bit data structure while the USB is ported with 32-bit data structure. Miscellaneous BIOS messages Keyboard Error Error in the keyboard connection. Make sure keyboard is connected properly. Keyboard/Interface Error Keyboard interface test failed.
137 POST error messages The following table lists the error codes and associated conditions that may occur during the POST portion of the BIOS.
138 5 Troubleshooting Error code Description 0046 DMA-2 error 0047 Unknown BIOS error. Error code = 147 (this is really a PMM_MEM_ALLOC_ERR) 0048 Password check failed 0049 Unknown BIOS error. Error code = 149 (this is really SEGMENT_REG_ERR) 004A Unknown BIOS error. Error code = 14A (this is really ADM_MODULE_ERR) 004B Unknown BIOS error.
139 Error code Description 0150 BSP processor failed BIST 0160 Processor missing microcode – P0 0161 Processor missing microcode – P1 0180 BIOS does not support current stepping – P0 0181 BIOS does not support current stepping – P1 0192 L2 cache size mismatch 0193 CPUID, processor stepping are different 0194 CPUID, processor family are different 0195 Front side bus mismatch 0196 CPUID, processor model are different 0197 Processor speeds mismatched 5120 CMOS cleared by jumper 5121
140 5 Troubleshooting Error code Description 8504 Bad or missing memory in slot 3B 8505 Bad or missing memory in slot 2B 8506 Bad or missing memory in slot 1B 8508 All memory marked as failed. Force all memory back online.
141 POST beep codes The following table lists the error beep codes. Prior to system video initialization, BIOS uses these beep codes to inform users of error conditions. The beep code occurs only when a critical error occurs or when the BIOS fails to boot to the operating system. Not all error conditions are supported by the BIOS beep codes.
142 5 Troubleshooting Troubleshooting BIOS beep codes The following table lists the possible beep codes thay may occur while using the system and is followed by solutions to the situation.
Appendix A: System management utility
This appendix shows you how to install the ASM software package and gives information about the software program and utilities bundled with your server.
145 Your Altos G5350 server supports the following system management utilities: • ASM (Acer Server Manager) This utility allows you to spot errors or potential trouble spots in the network servers through a single management station. For details go to page 147. • RAID configuration The system may be bundled with a SCSI or SATA RAID configuration utility. These utilities let you change the RAID configuration of your SCSI or SATA hard disk. For details go to page 149.
146 Appendix A: System management utility ASM Acer Server Manager is a server management tool. It is specially designed to help spot errors or potential trouble spots in the network servers through a single management station. ASM can send a query to a remote server over the network to request information such as system hardware and software configuration, system resource usage, and system performance. The complete ASM package consists of two major components — the ASM Agent and the ASM Console.
147 System setup Make sure that the system meets the requirements listed above before proceeding. You may also want to change your screen resolution to 800 x 600 or higher for optimum viewing. Installing ASM Agent Follow the steps below: 1 Log in to the managed server using the Administrator account. 2 Insert the EasyBUILD Management CD into the server’s CD-ROM drive. The installation sequence will automatically be displayed. 3 Select the option for ASM installation.
148 Appendix A: System management utility To launch the program, on the Windows taskbar click on the Start button, point to Programs, select Acer Server Management Suite then click ASM Console.
149 RAID configuration Caution! Using the RAID configuration utility erases all data previously saved in the hard drives. Make sure that you backup important files before starting the configuration process. SCSI RAID configuration utility The SCSI RAID configuration utility allows you to change the default RAID configuration, such as the system volume of your SCSI hard disk.
150 Appendix A: System management utility
Appendix B: Acer Altos G530 rack installation guide
This appendix shows you how to set up the Altos G5350 server in a rack mount configuration.
153 Setting up the system rack Important! Observe the electrostatic discharge (ESD) precautions indicated on page 35 when perfoming the following procedures. Do not attempt the procedures described in the following sections unless you are a qualified technician. Equipment rack precautions Follow the rack manufacturer's safety and installation instructions for proper rack installation.
154 • Appendix B: Acer Altos G530 rack installation guide Elevated operating ambient temperature The maximum operating temperature of the system is 35 °C (95°F). Careful consideration should be given to installing the system in an environment compatible with the 35 °C (95°F) maximum ambient temperature. • Reduced airflow The amount of airflow required for the safe operation of the equipment should not be compromised when installing the system in a rack.
155 System rack installation The Altos G5350 server system can also be mounted in a rack-model position. A rack mount kit is available for customers who want to convert a tower-mounted system to rack-model design. To purchase a rack mount kit, contact your local Acer representative or order directly from http://www.acer.com/. The figure below shows the Altos G5350 server in a rack-mount position.
156 Appendix B: Acer Altos G530 rack installation guide Vertical mounting hole pattern The four vertical rails of the system rack contain mounting holes arranged in a manner shown in the figure below: The system occupies 5U in the rack. Count the U positions and hole numbers from the bottom up. The distance from the center of two holes with closer spacing to the center of the next pair is equivalent to 1U. Note: The unit of measurement used in this guide is "U" (1U = 1.75 inches or 44.45 mm).
157 Screw types used The following screws are used in the assembly of the Altos G5350 system and bundled rack-mountable components: Screw type and part number Figure Usage #8-32 x 0.25 inch Securing the inner mounting rails to the system Hex head #6-32 0.
158 Appendix B: Acer Altos G530 rack installation guide Installing the system into the rack Caution! To minimize the chances of injuries, make sure that two or more people help in installing the server. To install the system into a four-post rack 1 Remove the foot stands from the server. (1) Lay the server on its side on a flat, stable surface (1). (2) Remove the screws that hold the foot stands to the bottom of the chassis (2). Keep these for later use. (3) Pull the stands from the server.
159 2 Remove the inner rails from the mounting rails. Note: The rack mount kit contains a pack of screws, two sets of side handles, rack brackets and mounting rails. The side handles are attached to the sides of the server. The rack brackets attach the mounting rails to the server. The mounting rails allow the server to slide in and out of the rackmount for maintenance purposes. Each mounting rail consists of: an inner rail, a middle slide, and a fixed outer rail.
160 3 Appendix B: Acer Altos G530 rack installation guide Attach the inner rails to the mounting shelf. (1) Align the inner rails to both sides of the mounting shelf (1). (2) Secure the rails to the mounting shelf using ten #8-32 screws (see page 157) (2). 4 Install the server into the mounting shelf. Caution! To avoid personal injury, care should be taken when pressing the inner rail release latches and sliding the component into the rack. (1) Place the server on the mounting shelf (1).
161 (2) Tighten the four thumbscrews on the rear of the mounting shelf (2). 5 Install the rack brackets to the rack by following the steps below: (1) Align the rack brackets to the mounting rail until the six screw holes become visible. (2) Secure the rack brackets to the mounting rails using six M4 x L8 metal screws and nuts (see page 157). Tighten the screws but leave them loose enough to allow length adjustment when installing the mounting rails to the rack.
162 6 Appendix B: Acer Altos G530 rack installation guide Install the M6 cage nuts (see page 157) into the rail. (1) Insert the lower lip of the cage nut over the bottom of the opening at the back of a rail. (2) With your fingers, pinch the cage nut rack fastener and push in until the top lip locks into position. (3) Repeat this process to install the other cage nuts in their appropriate locations.
163 7 Install the mounting rails to the rack by using four M6 x L10 metal screws (see page 157) for each mounting rail. 8 Extend the middle sliding piece of each mounting rail forward until you hear a click sound.
164 9 Appendix B: Acer Altos G530 rack installation guide Install the server shelf assembly into the rack. Caution! To avoid personal injury, care should be taken when pressing the inner rail release latches and sliding the component into the rack. (1) Carefully align the inner rails attached to the mounting shelf with the fully extended mounting rails on the rack. (2) Press the release latch on both sides of the mounting shelf (1).
165 (1) Attach the cable arm to the rear of the system using two M4 x L8 metal screws and nuts (see page 157). (2) Install two cage nuts into the rail to which the cable arm is to be attached. (3) Extend the cable arm enough to attach it to the rail using two M6 x L10 metal screws (see page 157).
166 Appendix B: Acer Altos G530 rack installation guide (4) Connect the power, peripheral and networking cables into their appropriate ports (1). Refer to “Connecting peripherals” on page 26 for detailed instructions. (5) Bundle all cables to the cable arm using the cable clamps (2).
Appendix C: SATA RAID configuration
This appendix shows you how to create a RAID volume in your SATA drives.
169 Configuring the SATA RAID This section shows how to create a RAID 1 (mirror) volume with the onboard SATA RAID function. This feature requires the installation or presence of a Intel 6300ESB ICH I/O controller. Enabling the onboard SATA RAID function 1 2 Load the BIOS default settings a During bootup, press F2 to enter the BIOS setup screen. b Press F9 to restore the default settings. c Press F10 to save changes and exit setup.
170 Appendix C: SATA RAID configuration Creating a RAID 1 volume 1 After rebooting the server, press Ctrl+E to enter the SATA RAID Configuration screen. The Management menu appears. 2 Select Configuration. The Configuration menu appears. 3 Select New Configuration, then select YES. An array selection window displays the devices connected to the current controller. 4 Use the arrow keys to select a specific drive, then press the spacebar to associate the selected drive with the current array.
171 (c) Press Ctrl+Alt+Del to reboot the server. 8 Install an Operating System to the RAID array.
172 Appendix C: SATA RAID configuration
Appendix D: SCSI RAID configuration
This appendix shows you how to create a RAID volume in your SCSI drives.
175 Configuring the SCSI/SCSI RAID HBA This section shows how to create a RAID 1 (mirror) volume. This feature requires the installation or presence of a LSI Logic 1020A SCSI controller. Using the SCSI HBA setup utility During bootup, press Ctrl+C to enter the LSI Logic Configuration screen. Loading the HBA default settings 1 In the LSI Logic MPT SCSI setup screen, press F2. 2 Select Global Properties, then select Restore Defaults. 3 Press Esc, then select Save changes then exit this menu.
176 Appendix D: SCSI RAID configuration If you change the settings in the Hot Spare field, the following messages appear: WARNING: Data on drive will be LOST! Press DELETE if data loss OK or any other key to cancel. 6 Press the Delete key to ignore. 7 Press Esc, then select Save changes then exit this menu. 8 To close the utility and reboot the server, follow the steps below: (1) Press Esc, then select Exit the Configuration Utility. The Global properties saved. Hit any key to reboot message appears.
177 Creating a RAID 1 volume 1 After rebooting the server, press Ctrl+M to enter the MegaRAID Configuration screen. The Management menu appears. 2 Select Configuration. The Configuration menu appears. 3 Select New Configuration, then select YES. An array selection window displays the devices connected to the current controller. 4 Use the arrow keys to select a specific drive, then press the spacebar to associate the selected drive with the current array.
178 Appendix D: SCSI RAID configuration 5 When initialization is complete, press any key to continue. 6 Press Esc to return to the Management menu. 7 To exit the utility and reboot the server, follow the steps below: (a) In the Management menu, press Esc. (b) Select YES. (c) Press Ctrl+Alt+Del to reboot the server. 8 Install an Operating System to the RAID array.
179 Index F A Acer Server Manager (ASM) system requirements ASM Agent 146 ASM Console 146 system setup 147 install ASM Agent 147 install ASM Console 147 B BIOS setup 79 Advanced 84 Chipset 99 CPU 85 Floppy 95 I/O Device 96 IDE 88 Memory 101 PCI 98, 99 USB 97 USB Mass Storage Device 98 Boot 103 ATAPI CD-ROM Devices 109 Boot Device Priority 106 Boot Settings Configuration 104 Hard Disk Drives 107 Removable Drives 108 entering 80 Exit 119 Main 82 Security 110 Administrator password 110 removing password 1
180 MegaRAID utility 176 assign hot spare 177 create RAID 1 177 initialize RAID volume 177 RAID volume initialization 176 SATA HBA utility 169 SATA RAID utility create RAID 1 170 enable 169 initialize RAID volume 170 load default settings 169 SCSI HBA utility 175 load default 176 load default settings 175 SCSI RAID HBA utility 175 create RAID 1 175 rear panel 10 S setting up the system 25 preinstallation requirements 25 specification additional media storage 4 SATA HDD cage 4 SCSI HDD cage 4 chipset 3 grap
