Acer Projector X118/X118AH/X118H/X1623H/H6540BD/ D606/D606B/D606D/D860D/E156D/ EV-S65/EV-S65A/EV-S65H/EV-WU80H/HE-806J/ V36SC/V36SB/V36S/V50U/GM532/ AS319D/AS319E/AS319/AU540/VH-432/ DX112G/DX112C/DX112/DX620/ BS-012E/BS-012K/BS-012/BS-520/ KS316B/KS316A/KS316/KU330/X1186G/ DSV1727/DSV1726/DSV1725/DWU1729/D1P1719 User's Guide
Copyright © 2017. Acer Incorporated. All Rights Reserved. Acer Projector User's Guide Original Issue: 09/2017 Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications.
iii Information for your safety and comfort Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. Turning the product off before cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
iv • Never use it under sporting, exercising, or any vibrating environment which will probably cause unexpected short current or damage rotor devices, lamp. Using electrical power • • • • • This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company. Do not allow anything to rest on the power cord. Do not locate this product where people will walk on the cord.
v Product servicing Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel.
vi • • • • • • • • • • • • • • • • • • contact your dealer. Do not keep using this product to break or drop it. In this case contact your dealer for inspection. Do not face the projector lens to the sun. It can lead to fire. When switching the projector off, suggest to ensure the projector completes its cooling cycle before disconnecting power. Do not frequently turn off the main power abruptly or unplug the projector during operation.
vii Caution for Listening To protect your hearing, follow these instructions. • • • • • Increase the volume gradually until you can hear clearly and comfortably. Do not increase the volume level after your ears have adjusted. Do not listen to music at high volumes for extended periods. Do not increase the volume to block out noisy surroundings. Decrease the volume if you can't hear people speaking near you. Disposal instructions Do not throw this electronic device into the trash when discarding.
viii First things first Usage Notes Do: • Turn off the product before cleaning. • Use a soft cloth moistened with mild detergent to clean the display housing. • Disconnect the power plug from AC outlet if the product is not being used for a long period of time. Don't: • Block the slots and openings on the unit provided for ventilation. • Use abrasive cleaners, waxes or solvents to clean the unit. • Use under the following conditions: • • • • In extremely hot, cold or humid environments.
First things first iii viii Usage Notes viii Precautions viii Introduction 1 Product Features 1 Package Overview 2 Projector Overview 3 Projector Outlook 3 Control Panel 5 Remote Control Layout 6 MHL (Mobile High-Definition Link) Control 8 Getting Started 10 Connecting the Projector 10 Turning the Projector On/Off 11 Turning on the Projector 11 Turning the projector off 12 Adjusting the Projected Image 13 Adjusting the Height of Projected Image 13 How to optimize image si
Troubleshooting 33 LED & Alarm Definition Listing 37 Replacing the Lamp 38 Ceiling Mount Installation 39 Specifications 42 Compatibility modes 46 Regulations and safety notices 51
1 Product Features This product is a single-chip DLP® projector. Outstanding features include: • DLP® technology • X118/X118AH/X118H/X1186G/D606/D606B/D606D/EV-S65/EV-S65A/ EV-S65H/V36S/V36SB/V36SC/AS319/AS319D/AS319E/DX112/DX112C/ DX112G/BS-012/BS-012E/BS-012K/KS316/KS316AK/S316B/DSV1725/ DSV1726/DSV1727 series: 800x600 SVGA resolution X1623H/D860D/EV-WU80H/V50U/AU540/DX620/BS-520/KU330/DWU1729/ H6540BD/E156D/HE-806J/GM532/VH-432/D1P1719 series: 1920x1200 WUXGA resolution resolution 4:3/16:9/ L.
English 2 Package Overview This projector comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immediately if any thing is missing.
3 English Projector Overview Projector Outlook Front / upper side 1 2 3 4 5 6 7 8 9 10 11 # 1 2 3 4 5 6 Description Lamp cover Air outlet Control panel Power button Zoom ring Air inlet # 7 8 9 10 11 Description Focus ring Remote control receiver Projection lens Lens cap Tilt adjusting wheels
English 4 Rear side 1 2 3 4 3 # 1 2 3 4 5 5 6 7 4 5 8 9 10 8 9 Description Power socket HDMI 1/MHL connector HDMI 2 connector 5V DC output connector (device charge & support mouse page up/down function) PC analog signal/HDTV/component video input connector # Description 6 7 8 9 RS232 connector Kensington™ lock port Composite video input connector Audio in connector 10 Audio out connector Note: Functions vary depending on model definition.
5 1 2 English Control Panel 3 4 7 8 5 9 6 # 1 Icon 10 Function POWER POWER Description Power Indicator LED 2 LAMP LAMP Lamp Indicator LED 3 TEMP TEMP Temp Indicator LED 4 POWER See the contents in "Turning the Projector On/Off" section. 5 Four directional select Use to select items or make keys adjustments to your selection. 6 7 8 BACK BACK SOURCE SOURCE ENTER 9 10 MENU Returns to the previous operation. Changes the active source. ENTER Confirm your selection of items.
English 6 Remote Control Layout 1 1 7 2 3 8 4 5 9 10 6 Model No:T-2501 MC.JPQ11.003 Model No:T-2502 26 2 7 8 9 4 5 10 6 11 19 11 19 12 20 12 13 21 13 20 21 14 15 22 23 14 15 22 23 16 24 16 24 17 18 25 17 18 25 Model No:J-25091 MC.JQ011.004 MC.JPQ11.004 # Icon Function Description 1 Infrared transmitter Sends signals to the projector. 2 POWER Refer to the "Turning the Projector On/Off" section. 3 MUTE To turn on/off the volume.
7 Icon Function Description 12 VGA Press "VGA" to change source to the VGA connector. This connector supports analog RGB, YPbPr (480p/576p/720p/ 1080i), YCbCr (480i/576i) and RGBsync. 13 FREEZE To pause the screen image. 14 PgUp For computer mode only. Use this button to select the previous page. This function is only available when USB Ctrl connector (mini type B) is connected to a computer via a USB cable. 15 COMPONENT No function. 16 PgDn For computer mode only.
English 8 MHL (Mobile High-Definition Link) Control 1 1 2 2 4 4 3 7 5 5 8 6 8 9 9 10 10 # Icon Function 1 SOURCE 2 MODE 3 7 6 Description Press the "SOURCE" button to toggle between Navigation, Numeric and Multi-Media mode. • • Press "MODE" button for one second to activate the MHL Control Mode. To exit, press the "MODE" button again. 3 Volume UP 4 Volume Down Decreases the volume. (only for Multi-Media mode) Increases the volume.
9 10 Icon Function KeyPad 0~9 Description Number buttons. (only for Numeric mode) Note: Functions vary depending on model definition.
English 10
English 10 Getting Started Connecting the Projector DVD player HDMI DVD player, Set-top Box, HDTV receiever HDMI R B G W R D-Sub USB MHL 4 3 2 Audio output 6 2 R B G 5 HDMI HDMI D-Sub W R HDTV adapter 7 8 7 HDMI 1 Y RS232 9 Y 11 11 Video output RS232 Smart Phone 10 RS232 Power Bank # Description # Description 1 Power cord 7 Audio cable Jack/RCA 2 HDMI cable 8 Audio cable Jack/Jack 3 MHL cable (MicroUSB to HDMI) 9 USB cable for charging device 4 VGA cable 1
11 Turning on the Projector 1 Ensure that the power cord and signal cable are securely connected. The Power indicator LED will flash red. 2 Turn on the projector by pressing "Power" button on the control panel or remote control, and the Power indicator LED will turn blue. 3 Turn on your source (computer, notebook, video player ,etc.). The projector will detect your source automatically.
English 12 Turning the projector off 1 To turn the projector off, press and hold the power button. This message appears: "Please press the power button again to complete the shutdown process." Press the power button again. 2 The LED power indicator will turn RED and blink rapidly after the projector is turned off, and the fan(s) will continue to operate for about 2 minutes to ensure that the system cools properly.
13 Adjusting the Height of Projected Image The projector is equipped with elevator feet for adjusting the height of image. To raise/lower the image: Use Tilt adjusting wheel to fine-tune the display angle.
English 14 How to optimize image size and distance Consult the table below to find the optimal image sizes achievable when the projector is positioned at a desired distance from the screen. • SVGA series If the projector is 2.0 m from the screen, good image quality is possible for image sizes between 46" and 51". Note: Remind as below figure, the space of 89 cm height is required when located at 2 m distance.
15 Note: Remind as below figure, the space of 87 cm height is required when located at 2 m distance. Ma x sc ree n Mi n scre size en s B ize 59" 45 " Height: 87 cm from base to top Height: of image 67 cm C A 2m Desired Distance Screen size Screen size Top Top Desired (Min zoom) (Max zoom) Distance From base to Diagonal Diagonal From base to top (m) W (cm) x H top of image W (cm) x H (inch) (inch) of image (cm) (cm) (cm) (cm) 1.0 22.55 49 x 30 33 29 63 x 39 43 2.
English 16 How to get a preferred image size by adjusting distance and zoom The table below shows how to achieve a desired image size by adjusting either the position or the zoom ring. • SVGA series To obtain an image size of 60" set the projector at a distance 2.4 m and 2.6 m from the screen. A 60" Desired image size D Height: 105 cm from base to top of image 2.4 m 2.6 m C Desired Image Size Diagonal (inch) 30 40 50 60 70 80 90 100 150 180 200 250 300 Zoom Ratio: 1.
17 A 60" Desired image size D Height: 89 cm from base to top of image 2.0 m 2.7 m C Desired Image Size Diagonal (inch) 34 50 60 70 80 90 100 120 150 200 250 300 Zoom Ratio: 1.3x B Desired Distance Distance (m) W (cm) x H (cm) Max zoom Min zoom 73 x 46 108 x 67 129 x 81 151 x 94 172 x 108 194 x 121 215 x 135 258 x 162 323 x 202 431 x 269 538 x 337 646 x 404 1.2 1.7 2.0 2.4 2.7 3.1 3.4 4.1 5.1 6.8 8.5 10.2 1.5 2.2 2.7 3.1 3.5 4.0 4.4 5.3 6.7 8.9 11.
English 20 User Controls Installation menu The installation menu provides an onscreen display (OSD) for projector installation and maintenance. Use the OSD only when the message "No signal input" is displayed on the screen. The menu options include settings and adjustments for screen size and distance, focus, keystone correction and more . 1 Turn on the projector by pressing "Power" button on the control pad.
21 The projector has multilingual OSD that allow you to make image adjustments and change a variety of settings. Using the OSD menus • To open the OSD menu, press "MENU" on the remote control or control panel. • When the OSD is displayed, use the keys to select any item in the main menu. After selecting the desired main menu item, press "ENTER" to enter submenu for feature setting. • Use the using the keys to select the desired item and adjust the settings by keys.
English 22 Color LumiSense Acer LumiSense technology can intelligently optimize the projection images to the most comfortable visual lumens automatically based on display content. The feature greatly enhances dark detail visibility and color saturation. • • Off: Default setting. • Boost: Select "Boost" to meet the visual effect of brightness boost. Normal: Select "Normal" to meet the visual effect of dark detail enhancement.
23 Saturation Tint Color Temperature "Contrast" controls the difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image. • Press to decrease the contrast. • Press to increase the contrast. Adjusts a video image from black and white to fully saturated color. • Press to decrease the amount of color in the image. • Press to increase the amount of color in the image. Adjusts the color balance of red and green.
English 24 Low Input Lag Use this function to make the projected screen smoothly without any lag. When the setting is set to "On", the 3D/Aspect Ratio/ Keystone/H. Position/V. Position/HDMI Scan Info/Tracking/Digital Zoom function will be reset to its factory default settings. Rename 1. When User choose the display mode "User 1" or "User 2", then OSD will showup the "color profile" and "rename" 2. Timely saved when user change the name. 3. Only English is supported.
25 Projection • Front: The factory default setting. • Rear: Reverses the image so you can project from behind a translucent screen. • Rear-Ceiling: When you select this function, the projector reverses and inverts the image at same time. You can project from behind a translucent screen with ceiling mounted projection. • • Front-Ceiling: When you select this function, the projector inverts the image for ceiling-mounted projection. Projection Mode • • Front: The factory default setting.
English 26 V. Position (Vertical position) • Press to move the image down. • Press to move the image up. Frequency "Frequency" changes the projector's refresh rate to match the frequency of your computer’s graphics card. If you can see a vertical flickering bar in the projected image, use this function to make the necessary adjustments. Tracking Synchronizes the signal timing of the projector with the graphics card.
27 Startup Screen Use this function to select your desired startup screen. If you change the setting, the changes will take effect when you exit the OSD menu. • Acer: The default startup screen of your Acer projector. Screen Capture Use this function to customize the startup screen. To capture the image that you want to use as the startup screen, follow the instructions below. Notice: Before proceeding with the following steps, make sure that the "Keystone" is set to the default value 0.
English 28 Security Security This projector provides a useful security function for the administrator to manage usage of the projector . Press "ENTER" to change the "Security" setting. If the security function is enabled, your must enter the "Administrator Password" first before changing the security settings. • Select "On" to enable the security function. The user has to enter a password to operate the projector. Please refer to the "User Password" section for details.
29 Reset Press the "ENTER" button and choose "Yes" to return the parameters on all menus to the factory default settings. Note: Functions vary depending on model definition. English Lock User Startup Screen Default Lock User Startup Screen is "Off". If lock user startup screen is "On", users cannot change startup screen anymore and avoid other users change that arbitrarily. Choose "Off" to unlock startup screen.
English 30 Management ECO Mode Choose "On" to dim the projector lamp which will lower power consumption, extend the lamp life and reduce noise. Choose "Off" to return normal mode. Gray out ECO mode item while either Lumisense or BluelightShield item is "On". High Altitude Choose "On" to turn on High Altitude mode. Operate the fans at full speed continuously to allow for proper high altitude cooling of the projector.
31 Display the projector information for Model Name, Input Source, Signal Type, Display Mode, Serial No., Software Version and QR code on the screen. Scan QR code linking to Acer projector portal via mobile. Lamp Information Lamp Hour Elapse Displays the lamp’s elapsed operating time (in hours). Lamp Reminding Activate this function to display a reminder to change the lamp 30 hours before its expected end-of-life. Lamp Hour Reset Choose "Yes" and press "ENTER"to turn the lamp hour counter to 0 hours.
English 32 Audio Volume Mute • Press to decrease the volume. • Press to increase the volume. • • Choose "On" to mute the volume. Choose "Off" to restore the volume. Note: Functions vary depending on model definition. 3D 3D Choose "On" to enable DLP 3D function. • On: Choose this item while using DLP 3D glasses, 120Hz 3D capable graphics cards and HQFS format file or DVD with corresponding SW player. • Off: Turn off 3D mode.
33 Language Language Choose the multilingual OSD menu. Use the key to select your preferred menu language. Press "ENTER" to confirm the selection. • English memory limitation, and once detect 24P 3D (96Hz or 144Hz) inputs, Aspect Ratio / HDMI Scan Info will be gray out, also HIDE will be not supported.
33 English Appendices Troubleshooting If you experience a problem with your Acer projector, refer to the following troubleshooting guide. If the problem persists, please contact your local reseller or service center. Image Problems and Solutions # 1 2 Problem No image appears onscreen Partial, scrolling or incorrectly displayed image (for PC (Windows 2000/XP/Vista/ Windows 7/ Windows 8)) Solution • Connected as described in the "Getting Started" section.
English 34 3 4 5 6 7 8 Partial, scrolling or incorrectly displayed image (For notebooks) The screen of the notebook computer is not displaying your presentation Image is unstable or flickering Image has vertical flickering bar Image is out of focus Image is stretched when displaying a "widescreen" DVD title • For an incorrectly displayed image: • Follow the steps for item 2 (above) to adjust the resolution of your computer. • Press the toggle output settings.
35 10 11 Image is too small or too large Image has slanted sides Image is reversed • • Adjust the zoom ring on the projector. • Press "MENU" on the remote control. Go to "Image -> Aspect Ratio" and try different settings or press "RATIO" on the remote control to adjust directly. • If possible, reposition the projector so that it is centered on the screen. • Press the "Keystone / " button on the remote control until the sides are vertical.
English 36 OSD Messages # 1 Condition Message Message Reminder • Fan Fail - the system fan is not working. • Projector Overheated - the projector has exceeded its recommended operating temperature and must be allowed to cool down before it may be used. Please check the following message. Please also check the dust filters if they are installed. If the dust filter is clogged with dust, please clean it. • Replace the lamp - the lamp is about to reach its maximum lifetime. Prepare to replace it soon.
37 English LED & Alarm Definition Listing LED Messages Lamp_LED Temp_LED Power LED Red Red Red Blue Flash ON to OFF 100ms Flash ON to OFF 100ms Flash ON to OFF 100ms -- Standby -- -- ON -- Power button ON -- -- -- ON Lamp retry -- -- -- Quick Flashing Power off (Cooling state) -- -- Quick Flashing -- Power button OFF (cooling completed; standby mode) -- -- ON -- Error (thermal failure) -- ON -- ON Error (fan lock) -- Quick Flashing -- ON ON -- -- ON Quick
English 38 Replacing the Lamp Use a screwdriver to remove the screw(s) from the cover, and then pull out the lamp. The projector will detect the lamp life. You will be shown a warning message "Lamp is approaching the end of its useful life in full power operation. Replacement suggested!" When you see this message, change the lamp as soon as possible. Make sure the projector has been cooling down for at least 30 minutes before changing the lamp.
39 If you wish to install the projector using a ceiling mount, please refer to the steps below: 1 Drill four holes into a solid, structural ceiling member, and secure the ceiling mount base to the ceiling. 2 Choose the length combination based on actual environment. (CM-01S doesn’t include Type 2 and Type 3.
English 40 3 Type 1: For the standard size use three bracket screws to mount the projector to the ceiling mount bracket. Type 2 and Type 3: Alternatively, for the larger size, use the sliding extensions for more supports. Type 1: Type 2: Type 3: Note: It is recommended that you keep a reasonable space between the bracket and the projector to allow for proper heat distribution. 4 Connect the main body connector to the projector bracket (illustration 1), and then screw up four screws (illustration 2).
41 Adjust the angle and positioning as necessary. English 360° Screw Type B Washer Type Diameter (mm) Length (mm) Large Small 4 25 V V SCREW SPEC. M4 x 25 mm 82.30mm 169.80mm 55.00mm 8.00mm 313.50mm 107.00mm 254.10mm 55.00mm 113.68mm 100.18mm 48.
English 42 Specifications The specifications listed below are subject to change without notice. For final specs, please refer to Acer's published marketing specifications.
43 • X118/X118AH/X118H/X1186G/D606/D606B/D606D/ EV-S65/EV-S65A/EV-S65H/V36S/V36SB/V36SC/AS319/ AS319D/AS319E/DX112/DX112C/DX112G/BS-012/ BS-012E/BS-012K/KS316/KS316AK/S316B/DSV1725/ DSV1726/DSV1727 series: F = 2.41 ~ 2.53, f = 21.85mm ~ 24.01mm, Manual Zoom & Focus • X1623H/D860D/EV-WU80H/V50U/AU540/DX620/ BS-520/KU330/DWU1729/H6540BD/E156D/HE-806J/ GM532/VH-432/D1P1719 series: F = 2.37 ~ 2.78, f = 16.91mm ~ 21.
English 44 Weight • X118/X118AH/X118H/X1186G/D606/D606B/D606D/ EV-S65/EV-S65A/EV-S65H/V36S/V36SB/V36SC/AS319/ AS319D/AS319E/DX112/DX112C/DX112G/BS-012/ BS-012E/BS-012K/KS316/KS316AK/S316B/DSV1725/ DSV1726/DSV1727 series: 2.7 Kg (5.95 lbs) • X1623H/D860D/EV-WU80H/V50U/AU540/DX620/ BS-520/KU330/DWU1729/H6540BD/E156D/HE-806J/ GM532/VH-432/D1P1719 series: 3.1 Kg (6.
45 X118/D606/ EV-S65/V36SC/ AS319D/DX112G/ BS-012E/ KS316B/X1186G/ DSV1727 X118AH/D606B/ EV-S65A/ V36SB/AS319E/ DX112C/ BS-012K/KS316A/ DSV1726 X118H/D606D/ EV-S65H/ V36S/AS319/ DX112/ BS-012/KS316/ DSV1725 H6540BD/E156D/ HE-806J/GM532/ VH-432/D1P1719/ X1623H/D860D/ EV-WU80H/ V50U/ AU540/DX620/ BS-520/KU330/ DWU1729 Power socket V V V V VGA IN V X V V HDMI X V V X HDMI 2 X X X V HDMI 1/MHL X X X V Composite video X X V V RS232 X X X V 3.
English 46 Compatibility modes A.
47 VGA Analog - Extended Wide timing Modes WXGA WSXGA+ WUXGA 3 Resolution 1280x768 1280x768 1280x768 1280x720 1280x720 1280x800 1280x800 1920x1200 1440x900 1680x1050 1920x1080 (1080P) 1366x768 1920x1200-RB V.Frequency [Hz] 60 75 85 60 120 60 119.909 60 60 60 H.Frequency [KHz] 47.8 60.3 68.6 44.8 92.9 49.6 101.6 74 59.9 65.3 60 67.5 60 59.94 47.7 74.04 VGA Analog -Component Signal Modes Resolution V.Frequency [Hz] H.
English 48 XGA SXGA QuadVGA SXGA+ UXGA PowerBook G4 PowerBook G4 PowerBook G4 PowerBook G4 PowerBook G4 PowerBook G4 i Mac DV (G3) 2 800x600 800x600 800x600 800x600 800x600 1024x768 1024x768 1024x768 1024x768 1024x768 1152x864 1152x864 1152x864 1280x1024 1280x1024 1280x1024 1280x1024 1280x960 1280x960 1400x1050 1600x1200 640x480 640x480 800x600 1024x768 1152x870 1280x960 1024x768 60 72 75 85 120 60 70 75 85 120 70 75 85 60 72 75 85 60 75 60 60 60 66.6(67) 60 60 75 75 75 37.9 48.1 46.9 53.7 77.4 48.
49 3 4 60 67.5 60 59.94 47.7 74.04 HDMI - Video Signal Modes Resolution V.Frequency [Hz] H.Frequency [KHz] 480i 576i 480p 576p 720p 720p 1080i 1080i 1080p 1080p 1080p 1080p 720x480(1440x480) 720x576(1440x576) 720x480 720x576 1280x720 1280x720 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1200-RB 59.94 (29.97) 50(25) 59.94 50 60 50 60(30) 50(25) 23.97/24 60 50 59.94 15.7 15.6 31.5 31.3 45.0 37.5 33.8 28.1 27.0 67.5 56.3 74.04 HDMI - 1.
English 50 Graphic source monitor range limits 15k-100kHz 24-120 Hz Analog:165MHz Digital:165MHz Horizontal scan rate: Vertical scan rate: Max. pixel rate: C. MHL Digital Modes Resolution VGA 480i 576i 480p 480p_2x 576p 576p_2x 720p 720p 1080i 1080i 1080p 1080p 1080p 640x480 720x480 (1440x480) 720x576 (1440x576) 720x480 1440x480 720x576 1440x576 1280x720 1280x720 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 Horizontal scan rate: Graphic source monitor Vertical scan rate: range limits Max.
FCC notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
English 52 Remarque à l'intention des utilisateurs canadiens Cet appareil numérique de la classe B est conforme a la norme NMB-003 du Canada. Compliant with Russian/ Ukraine regulatory certification Radio device regulatory notice Note: The regulatory information below is for models with wireless LAN and/or Bluetooth only. General This product complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use.
Acer Incorporated 8F, 88, Sec. 1, Xintai 5th Rd., Xizhi New Taipei City 221, Taiwan of Conformity We, Acer Incorporated 8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan And, Acer Italy s.r.l. Via Lepetit, 40, 20020 Lainate (MI) Italy Tel: +39-02-939-921 ,Fax: +39-02 9399-2913 www.acer.
Acer America Corporation 333 West San Carlos St., Suite 1500 San Jose, CA 95110 U. S. A. Tel: 254-298-4000 Fax: 254-298-4147 www.acer.com Federal Communications Commission Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
