Acer LCD Monitor User’s Guide
Copyright © 2020. Acer Incorporated. All Rights Reserved. Acer LCD Monitor User’s Guide Original Issue: 4/2020 Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications.
Special notes on LCD monitors The following are normal with the LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the power switch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • The LCD screen has 99.99% or more effective pixels. It may include blemishes of 0.
Accessibility Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power from the equipment, be sure to unplug the power cord from the electrical outlet. Safe listening To protect your hearing, follow these instructions. • Gradually increase the volume until you can hear it clearly and comfortably and without distortion.
power company. • Do not allow anything to rest on the power cord. Do not locate this product where people will walk on the cord. • If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating.
personnel when: • the power cord or plug is damaged, cut or frayed • liquid was spilled into the product • the product was exposed to rain or water • the product has been dropped or the case has been damaged • the product exhibits a distinct change in performance, indicating a need for service • the product does not operate normally after following the operating instructions Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other contro
Disposal of Waste Equipment This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
• pain, swelling or throbbing • stiffness or tightness • coldness or weakness If you have these symptoms, or any other recurring or persistent discomfort and/or pain related to computer use, consult a physician immediately and inform your company’s health and safety department. The following section provides tips for more comfortable computer use.
• minimizing room light by using drapes, shades or blinds • using a task light • changing the display’s viewing angle • using a glare-reduction filter • using a display visor, such as a piece of cardboard extended from the display’s top front edge • Avoid adjusting your display to an awkward viewing angle. • Avoid looking at bright light sources, such as open windows, for extended periods of time.
Viale delle Industrie 1/A, 20020 Arese (MI), Italy RG241Y RG241Y xxxxxx (“x” = 0~9, a ~ z, A ~ Z, or blan k) EN 55032:201 /AC:201 Class B EN 61000-3-2:2014 Class D 2020. _______________________________ RU Jan / Sr. Manager Acer Incorporated (Taipei, Taiwan) Apr.
Acer America Corporation 333 West San Carlos St., San Jose Suite 1500 CA 95110, U. S. A. Tel : 254-298-4000 Fax : 254-298-4147 www.acer.com Federal Communications Commission Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Special notes on LCD monitors Information for your safety and comfort Safety instructions Cleaning your monitor Connecting/disconnecting the device Accessibility Safe listening Warnings Using electrical power Product servicing Potentially explosive environments Additional safety information IT Equipment Recycling Information Disposal instructions LCD pixel statement Tips and information for comfortable use Declaration of Conformity iii iii iii iii iii iv iv iv iv v vi vi vi vii vii vii Federal Communica
Unpacking LCD monitor DP cable (Optional) Quick start guide HDMI cable (Optional) English Please check that the following items are present when you unpack the box, and save the packing materials in case you need to ship or transport the monitor in the future.
Attaching/ Removing the base 1. Take out the monitor, base from the package, put them on English smooth surface. 2.Align the stand for the back cover portion of the monitor, insert the back cover, ensure that the monitor and.stand connection is stable, do not shake. 3. Align base , insert the base to stand arm, rotating hand screw until tightening, fix the base.
Screen position adjustment To optimize the viewing position, you can adjust the monitor tilt by using English both of your hands to hold the edges of the monitor as shown below. The monitor can be adjusted to 15degrees up or 5 degrees down.
English Connecting the Power cord • Check first to make sure that the power cord you use is the correct type required for your area. • The monitor has a universal power supply that allows operation in either 100/120 V AC or 220/240 V AC voltage area. No user-adjustment is required. • Plug one end of the power cord to the AC inlet, and plug the other end into an AC outlet. • For units using 120 V AC: Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.
English Connector pin assignment 19-Pin Color Display Signal Cable* PIN Meaning PIN Meaning 1. TMDS Data2+ 10. TMDS Clock+ 2. TMDS Data2 Shield 11. TMDS Clock Shield 3. TMDS Data2- 12. TMDS Clock- 4. TMDS Data1+ 13. CEC 5. TMDS Data1 Shield 14. Reserved (N.C. on device) 6. TMDS Data1- 15. SCL 7. TMDS Data0+ 16. SDA 8. TMDS Data0 Shield 17. DDC/CEC Ground 9. TMDS Data0- 18. +5V Power 19.
Standard timing table English No. Mode 1 2 640x480 VGA 3 Refr esh Rate 60 Hz 640x480 72 Hz 640x480 120 Hz 4 MAC 640x480 66.
English ------------------------------------------------------------------------------------------------------------Note: DP(1.2):1920x1080 supports up to 144Hz in normal mode (supports to 165Hz in overclocking mode),also supports FreeSync and HDR function. HDMI(2.0):1920x1080 supports up to 144Hz in normal mode (supports to 165Hz in overclocking mode),also supports FreeSync and HDR function. HDMI(2.
English Users controls External controls Function key a. b. c. d. 8 Monitor power off status Press to switch power on. In the normal display, anytime to Press more than 5 seconds switch to turn off the power. Blue indicates power on. Amber flicker indicates standby/power saving mode. No light display indicates Power off. Press to any directions switch key to display First Menu. Press again to enter next function in the First Menu.
Using the Shortcut Menu English ‑-----------------------------------------------------------------------------------------------------------Note: The following content is for general reference only. Actual product specifications may vary. The OSD (onscreen display) can be used to adjust the settings of your LCD monitor. Press the MENU key to open the OSD. You can use the OSD to adjust the picture quality and general settings. For advanced settings, please refer to following page: Main page 1.
Selecting the input English Open the Input control and select HDMI1(2.0), HDMI2(2.0), DP or Auto Source. When you are done, press the joystick to exit current page and store. The Function page Open the Function page to adjust the functions, settings which you want using the arrows. When you are done, toggle the joystick to the left or right to go back one level. Adjusting the Picture 1. Press the MENU key to open the OSD. 2. Toggle the joystick to the up or down to select Picture from the OSD.
7. Black Boost: This boosts the amplitude of the dark color levels of the display-blacks will be less black.The higher the level,the higher the boost. 8. Blue Light: Filters out blue light to protect your eyes by adjusting how much blue light is shown -- 80%, 70%, 60%, or 50%. ‑---------------------------------------------------------------------------------------------------------Note: Higher values allow more blue light through. For the best protection select a lower value. 9.
English ---------------------------------------------------------------------------------------------------------Note: 1. If Color Space is "HDR",then Modes is set to "HDR" automatically. 2. If Color Space is not "HDR",then Modes is set to "Standard". 8. Grayscale Mode: Default is off. Based on favorite to turn on or off. 9. 6-axis Hue: Adjust the red, green, blue, yellow, magenta and cyan hue. 10. 6-axis Saturate: Adjust the red, green, blue, yellow, magenta and cyan saturation.
VRB: TO choose whether to support dynamic picture more clean control ，default is off. --------------------------------------------------------------------------------------------------------------------Note: 1.it is not support VRB when HDR set to“ON"or“Auto”. 2.VRB function does not affect the(Logo,Aim Point,Message and Input Icon)brightness 3.When turn on FreeSync，will set VRB to“Off”automatically 4.When to adjust Brightness，Blue Light and ACM，will set VRB to“off”automatically 5.
English Adjusting the System 1. Press the MENU key to open the OSD. 2. 3. Toggle the joystick to the up or down to select System from the OSD.Then toggle to the right to navigate to the element you wish to adjust and press the joystick to enter it. Toggle to the left or right to adjust the sliding scales. 4. Input: Select the source from HDMI1(2.0) ,HDMI2(2.0) ,DP. 5. Auto Source: Automatically searches for available input sources. 6. DP Format: Select the source from DP 1.1,DP1.2. 7.
English Save Setting to…(User mode only) 1. Press the MENU key to open the OSD. 2. Toggle the joystick to the up or down to select "Save Setting to..." from the OSD.Then toggle to the right to navigate to the element you wish to adjust and press the joystick to enter it. 3. save setting to Game mode:There are three user-defined profiles available（Action， Racing and Sports).
