Acer Aspire 1650 Series Service Guide Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.tw PRINTED IN TAIWAN download service manual and resetter printer at http://printer1.blogspot.
Revision History Please refer to the table below for the updates made on Aspire 1650 service guide. Date 2006/8/18 Chapter Chapter 2 Updates Update BIOS specification. II download service manual and resetter printer at http://printer1.blogspot.
Copyright Copyright © 2005 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated. Disclaimer The information in this guide is subject to change without notice.
Conventions The following conventions are used in this manual: SCREEN MESSAGES Denotes actual messages that appear on screen. NOTE Gives bits and pieces of additional information related to the current topic. WARNING Alerts you to any damage that might result from doing or not doing specific actions. CAUTION Gives precautionary measures to avoid possible hardware or software problems. IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.
Preface Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability).
VI download service manual and resetter printer at http://printer1.blogspot.
Chapter 1 System Specifications Features This computer was designed with the user in mind. Here are just a few of its many features: Performance T T T T Intel® 915GM PCI Express chipset Intel® Pentium® M processor 725A/730/740/750/760/770/780 (2MB L2 cache, 1.6 GHz, 400 MHz FSB) or higher CPU Package is uFPGA 478 Package Integrated Intel® PRO/Wireless 2200BG network connection (dual-mode 802.
Storage T 40 GB and above E-IDE hard disk (2.5”, 9.5mm, UltraDMA-100) T Optical drive options: tray type DVD-Dual double-layer or DVD/CD-RW combo T Tray type DVD-Dual double-layer drive; Read: 8X DVD-ROM, 6X DVD-R, 6X DVD+RW, 6X DVD-RW, 6X DVD+R, 6X DVD+R DL (double-layer), 24X CD-RW, 24X CD-R; Write: 24X CDR, 10X CD-RW, 8X DVD+R, 8X DVD-R, 4X DVD+RW, 2.
Mainboard Placement Top View Chapter 1 download service manual and resetter printer at http://printer1.blogspot.
Rear View 4 Chapter 1 download service manual and resetter printer at http://printer1.blogspot.
ITEM DESCRIPTION ITEM DESCRIPTION CN2 LCD Connector CN14 DC JACK CN3 LED board connector CN15 CRT connector SW2 Lid switch CN16 Docking connector CN10 express card connector CN17 Battery connector CN11 4 IN 1 connector CN18 Fix ODD connector CN13 Speaker connector CN21 Swap ODD connector CN9 MD board connector CN24 2nd Battery connector CN12 INT MIC connector CN30 PATA HDD connector CN5 Keyboard connector CN31 SATA HDD connector CN6 BT connector CN36 Line IN connec
Block Diagram 5VPCU 5V / 3.3V / 12V 3V_ALWAYS Page : 35 +12V Centrino CLOCK GEN ICS ICS954201 +5V CRANE2 ( ZL3 ) DOTHAN CELEROM-M Page : 2 3V_S5 INTEL Mobile_479 CPU Page : 3 , 4 ATI M26P/M24P 64M / 128M PCIE 3VSUS HOST BUS 533MHz HOST BUS 400MHz 5VSUS 2.5VSUS 1.8V / 0.9V Page : 36 +1.8V DDR2-SODIMM1 400/533MHZ DDR2 EXT_TV-OUT SWITCH CIRCUIT CRT Page:17 LVDS INT_LVDS RGB INT_CRT TVOUT INT_TV-OUT LVDS 1257 BGA Page:16 Page:9~10 MVREF_DM EXT_CRT Page : 11 ~ 14 ALVISO +2.
Outlook View A general introduction of ports allow you to connect peripheral devices, as you would with a desktop PC. Open View # Item Description 1 Display screen Also called Liquid-Crystal Display (LCD), displaying computer output. 2 Microphone Internal microphone for sound recording. 3 Keyboard For entering data into your computer. 4 Palmrest Comfortable support area for your hands when you use the computer.
# # "Launch keys" on page 10 on page 10 "Launch keys" Description "Launch keys" on page 10 Item Item Description "Launch keys" on page 10 Front Panel "Launch keys" on page 10 "Launch keys" on page 10 # Icon Item Description # Icon Icon ## Icon Item Item Description Description # 1 Icon # # Icon Icon 2 Description Item ItemSpeakers Item Power indicator # Icon Item Description Description Left and right speakers deliver stereo audio Description output.
Left View # Item Description 1 Optical drive Internal optical drive; accepts CDs or DVDs depending on the optical drive type. 2 LED indicator Lights up when the optical drive is active. 3 Optical drive eject button Ejects the optical drive tray from the drive. 4 Emergency eject hole Ejects the optical drive tray when the computer is turned off NOTE: The positions of the AcerMedia indicator, eject button and emergency eject hole may differ depending on the optical drive module installed.
Right View # # # Icon Item Description Icon Item Description Icon 1 2 # Icon Item Description PC Card slot eject button Ejects the PC Card from the slot. PC Card slot Connects to one Type II CardBus PC Card. Item Description Note: Note: # Icon 3 Item Two USB 2.0 ports Description Connect to Universal Serial Bus (USB) 2.0 devices (e.g., USB mouse, USB camera). Note: 4 Ethernet (RJ-45) port 5 Modem (RJ-11) port Connects to a phone line.
Rear View # # 1 Icon ## Icon Icon Icon Item Item Item Description Item Description Description Description Power jack Connects to an AC adapter. 2 External display port Connects to a display device (e.g., external monitor, LCD projector). 3 Security keylock Connects to a Kensington-compatible computer security lock. Bottom View # Chapter 1 Item Description 1 Hard disk bay Houses the computer's hard disk (secured with two screws).
# 12 Item Description 5 Cooling fan Helps keep the computer cool. NOTE: Do not cover or obstruct the opening of the fan. 6 Memory compartment Houses the computer's main memory and Mini PCI Card. Chapter 1 download service manual and resetter printer at http://printer1.blogspot.
Indicators Your computer provides an array of three indicators located above the keyboard, in addition to four indicators positioned at the front of the palm rest area. These indicators show the status of the computer and its componetns. Icon Function Description The three indicators located above the keyboard provide the following status information: Icon Item Description Caps Lock activity Lights when Caps Lock is activated. Num Lock activiy Lights when Num Lock is activated.
Easy-launch buttons The build-in touchpad is a PS/2 compatible pointing device that senses movement on its surface. The cursor responds to your finger movements on the touchpad. In addition, the two click buttons provide the same functionality as a computer mouse, while the scroll key enables easy up and down scrolling in documents and web pages. The touchpad is located in the middle of the palm rest area, providing maximum comfort and efficiency.
Touchpad The build-in touchpad is a PS/2 compatible pointing device that senses movement on its surface. The cursor responds to your finger movements on the touchpad. In addition, the two click buttons provide the same functionality as a computer mouse, while the scroll key enables easy up and down scrolling in documents and web pages. The touchpad is located in the middle of the palm rest area, providing maximum comfort and efficiency.
Using the Keyboard The full-sized keyboard includes an embedded numeric keypad, separate cursor keys, two Windows keys and twelve function keys. Lock keys and embedded numeric keypad The keyboard has four lock keys which you can toggle on and off. The computer features three lock keys, each with its own status indicator light. Lock Key Description Caps Lock When Caps Lock is on, all alphabetic characters are typed in uppercase.
Key Description Windows logo key Pressed alone, this key has the same effect as clicking on the Windows Start button; it launches the Start menu.
Hot Key Icon Function Description Fn-F2 Acer eSetting Launches the Acer eSettings in Acer eManager. Fn-F3 Acer ePowerManagement Launches the Acer ePowerManagement in Acer eManager. Fn-F4 Sleep Puts the computer in Sleep mode. Fn-F5 Display toggle Switches display output between the display screen, external monitor (if connected) and both. Fn-F6 Screen blank Turns the display screen backlight off to save power. Press any key to return.
The Euro symbol 1. Open a text editor or word processor. 2. Either directly press the symbol at the bottom-right of the keyboard, or hold and then press the<5> symbol at the upper-center of the keyboard. The US dollar sign 1. Open a text editor or word processor. 2. Either directly press the key at the bottom-right of the keyboard, or hold and then press the <4> key at the upper-center of the keyboard. NOTE: This function varies by the operating system version.
Using System Utilities Acer eManager Innovative Acer eManagement software is designed for easy access to frequently used functions. At the press of Acer Empowering Key, the Acer eManager user interface appears, featuring four main settings -- Acer eSetting, Acer ePresentation, Acer ePowerManagement and Acer eRecovery.
Start All Programs Chapter 1 Launch Manager 21 download service manual and resetter printer at http://printer1.blogspot.
Hardware Specifications and Configurations Processor Item CPU type Specification Intel® Pentium® M Processor at 1.5 ~2.13 GHz or higher Intel® Celeron® M Processor at 1.3~1.5 GHz or higher CPU package uFPGA 478 CPU core voltage Depend on DVI CPU I/O voltage 1.
System Memory Item Specification Memory controller 915PM/915GM Memory size 256MB/512MB DIMM socket number 2 Supports memory size per slot 1024 MB Supports maximum memory size 2GB Supports DIMM type DDRII SDRAM standard Supports DIMM Speed 400/533 MHz Supports DIMM voltage 1.8V Memory module combinations You can install memory modules in any combinations as long as they match the above specifications. .
Item Specification Audio Controller AC’ 97 Codec Audio onboard or optional Built-in Mono or Stereo Stereo Resolution 20 bit stereo Digital to analog converter 18 bit stereo Analog to Ditial converter Compatibility Microsoft PC99/2100, AC97 2.3 & WHQL/WLP2.
Battery Item Specification Vendor & model name Panasonic/Sanyo Battery Type Li-ion Pack capacity 65Wh Cell voltage 3.
LCD:15”XGA Item Specifications Vendor & model name AU B150XG02 V.2 LG LP150X08-A3 Samsung LTN150XBL03-C00 Hitachi TX38D81VC1 CAB Rev.C CMO N150X3-L07 Mechanical Specification LCD display area (diagonal, inch) 15” 15” 15” 15” 15” Display technology TFT TFT TFT TFT TFT Resolution XGA (1024*768) XGA (1024*768) XGA (1024*768) XGA (1024*768) XGA (1024*768) Supports colors 16.7 million 16.7 million 16.7 million 16.7 million 16.
AC Adapter Item Specification Frequency variation range (Hz) 47 - 63 Nominal voltages (Vrms) 90 - 264 Inrush current The maximum inrush current will be less than 50A and 100A when the adapter is connected to 100Vac(60Hz) and 240Vac(50Hz) respectively. Efficiency High efficiency 85% minimum, at 100~240Vac AC input, full load, warm-up condition. Output Ratings (CV mode) DC output voltage Offers constant voltage 19.0V output source with 150W max output power capacity.
Dimensions and Weight Item Details Deminsions 360(W) x 273(D) x 27~32 (H)mm Weight 6.6lbs (3kg) Environmental Requirements Item Specification Temperature Operating +5 ~ +35°C Non-operating -20 ~ +65°C (storage package) Humidity Operating 20% ~ 80% without condensation Altitude Operating sea level 0 to 10,000ft Storage sea level 0 to 40,000ft Model Name MK4025GAS ,KA100A, 40GB Pluto MK6025GAS 60GB Pluto MK8025GAS, 8MB, 80GB 40.007GB 60.0116GB 80.
TOSHIBA Number of Disks 1 2 2 Heads 16 16 16 Cylinders 16,383 16,383 16,383 User Sectors/Track at zone 0 63 63 63 Logical Blocks (LBA) 78,140,160 117,210,240 156,301,488 100MB/sec 100MB/sec 100MB/sec Track-to-track 2ms 2ms 2ms Average 12ms 12ms 12ms Maximum 22ms 22ms 22ms Logical Configuration Data Transfer Rate Max transfer rate to host Seek Time TOSHIBA Nominal Power Requirements Logic +5V( ± 5 %) +5V( ± 5 %) +5V( ± 5 %) Start 4.7watts 5.0watts 4.
Operating Vibration 9.8 M/S2 (1.0G), 5 - 500 Hz 9.8 M/S2 (1.0G), 5 - 500 Hz 9.8 M/S2 (1.
Chapter 2 System Utilities BIOS Setup Utility The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/ Output System). Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises.
Information Note: This page displays information of the system. Data on the fields (such as CPU type, CPU Speed, Product Name) are subject to different models. PhoenixBIOS Setup Utility . Info. Main CPU Type: : Security Boot CPU Speed: Intel (R) Pentium (R) M processor 1.73GHz 1733 MHz HDD Model Name: HDD Serial Number: ATAPI Device: System BIOS Ver: TOSHIBA MK4025GAS Y4C59830S HL-DT-ST DVDRAM GMA-4080N S3A11 VGA BIOS Ver: KBC Ver: Serial Number ATi 008.018M.039.
Parameter Description Serial Number This item will show the Serial number of system. Asset Tag Number This item will show the Asset Tag number of the system. Product Name This field will show product name. Manufacturer Name This field will show manufacturer name. UUID This will be visible only when there is an internal LAN device present. Chapter 2 33 download service manual and resetter printer at http://printer1.blogspot.
Main PhoenixBIOS Setup Utility Info. Advanced Main Security Boot Exit Item Specific Help System Time: [02:19:31] System Date: [04/21/2004] System Memory: 624 KB , , or selects field.
Parameter Description Network boot When this is selected, Boot from LAN feature is enabled. When this is not selected, Boot from LAN feature is then disabled. F12 Boot Menu When this is selected, users can modify device boot priority by pressing F12 key during POST. When this is not selected, device boot priority will not be adjustable during POST.
Advanced The Advanced screen contains parameters involving your hardware devices. It also provides advanced settings of the system. PhoenixBIOS Setup Utility Info. Main Advanced Security Boot Exit Item Specific Help All items on this menu cannot be modified in user mode. If any items require changes, please consult your system Supervisor.
Security The Security screen contains parameters that help safeguard and protect your computer from unauthorized use. Info. PhoenixBIOS Setup Utility Security Advanced Main Boot Exit Item Specific Help Supervisor Password Is: Clear User Password Is: Clear HDD Password Is: HDD Master ID: Clear Set Supervisor Password Set User Passord Set HDD Password [Enter] [Enter] Password on boot [Disabled] 43883467 Supervisor Password controls accesses to the setup utility.
Parameter Description Option Set HDD Password When shown as [Locked], the hard drive password currently can not be changed or disabled. To change or disable it, turn off the system and enter Setup immediately after turning it back on. Press [Enter] to input change, or disable hard drive password. Enter Password on boot Defines whether a password is required or not while the events defined in this group happened.
User can now type password in field “Enter New Password”, and re-enter password in field “Confirm New Password” for verification. If the verification is OK: The password setting is complete after user presses enter. Setup Notice Changes have been saved.
Boot This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay and onboard LAN device. PhoenixBIOS Setup Utility Info. Main Advanced Security Boot Exit Item Specific Help CD-ROM/DVD Drive Floppy Devices +Hard Drive Network Boot + and - indicate device categories. Use to expand/collapses.
Exit The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use. PhoenixBIOS Setup Utility Info. Main Advanced Security Item Specific Help Exit Saving Changes Exit Dicarding Changes Load Setup Defaults Discard Changes Save Changes F1 Help Esc Exit ↑ ↓ ←→ Exit Boot Exit System Setup and save your changes to CMOS.
Chapter 3 Machine Disassembly and Replacement This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting. To disassemble the computer, you need the following tools: T Wrist grounding strap and conductive mat for preventing electrostatic discharge T Small Philips screw driver T Philips screwdriver T Plastic flat head screw driver Tweezers NOTE: The screws for the different components vary in size.
General Information Before You Begin Before proceeding with the disassembly procedure, make sure that you do the following: 1. Turn off the power to the system and all peripherals. 2. Unplug the AC adapter and all power and signal cables from the system. 3. Remove the battery pack. NOTE: The screws used to secure bottom case and upper case are more than one type. Please group same type of screw together as you disassemble the system for service purpose. The image below is for your reference.
Screw Type Location Quantity M2.5*6 Bottom case and IO bezel (hightlight with yellow circle) 14 M2.5*6 Remove the IO bezel then you will see. 2 M2.5*6 Remove the heatsink cover then you will see. 1 M2.5*6 Remove the HDD cover then you will see. 1 M2.5*3 Detach the HDD module then you will see. 1 M2.5*3 Remove the battery then you will see. 1 Chapter 3 45 download service manual and resetter printer at http://printer1.blogspot.
Disassembly Procedure Flowchart The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
LCD Module 4 screw pads M*4 LCD Bezel *6 hinges *2 brackets LCD Inverter Antenna set LCD Cover LCD Assembly *4 LCD LCD Cable LCD Brackets Screw List Item Chapter 3 Description SCREW M2.0X3.0-I-NINYLOK 86.A03V7.012 SCREW I2.5*3MBNIH(M2.5L3) 86.T25V7.012 SCREW M2.5*4L-BZNNYLOK 86.A03V7.006 SCREW M2.0X5-I-NINYLOK 86.T23V7.006 SCREW MM25060IL69 86.A08V7.004 SCREW M2.0*5I(NI)(NYLOK) 86.T23V7.010 SCREW M2.0X2.5-I-NINYLOK 86.A03V7.007 SCREW I2*3M-NIHY (M2L3) 86.T25V7.008 SCREW M1.7*3.
Removing the Battery Pack NOTE: This chapter is base on Aspire 1410 and Aspire 1680 to edit. Since they have the similar disassemble and reassemble procedures. 48 1. Unlock the battery lock. 2. Slide the battery latch as shown then remove the battery pack. Chapter 3 download service manual and resetter printer at http://printer1.blogspot.
Removing the HDD Module/the memory and the Wireless LAN Card/ the Thermal Module and the CPU/ODD and the LCD Module Removing the HDD Module 1. Remove the two screws holding the HDD cover. 2. Remove the HDD cover. 3. Detach the HDD module then remove it. Removing the Memory and the Wireless LAN Card 1. Remove the two screws that secure the RAM/Wireless cover. 2. Remove the RAM/Wireless cover. 3. Pop up the memory then remove it. 4. Disconnect the auxiliary and the main wireless antennae. 5.
Removing the Thermal Module and CPU 1. Remove the two screws holding the IO bezel. 2. Then remove the IO bezel. 3. Remove the two screws that secure the heatsink cover. 4. Remove the heatsink cover from the main unit. 5. Disconnect the fan cable. 6. Remove the four screws that secure the thermal module. 7. Pull the thermal module outwards then remove it. NOTE: The edge of the thermal module as shown is very sharp. Be very careful as you remove the thermal module. 50 8.
Removing the ODD Module 1. Remove the three screws holding the middle cover. 2. Detach the middle cover carefully. 3. Turn over the keyboard as shown. 4. Disconnect the keyboard cable from the main board then remove the keyboard. 5. Remove the screw that fastens the ODD module. . 6. Turn over the notebook computer then detach the ODD module carefully. NOTE: When you reattach the ODD, please make sure you attach the ODD module completely to the main unit.
Removing the LCD Module 1. Remove the three screws holding the keyboard cover. 2. Open the LCD module as the picture shown then detach the keyboard cover from the main unit. 3. Remove the two screws that secure the keyboard as shown. 4. Turn over the keyboard as shown and disconnect the keyboard cable then remove the keyboard. 5. Pull out the antenna set with a tweezers then take out the antenna set from the main unit. 6. Disconnect the LCD coaxial cable. 7.
Disassembling the Main Unit Separate the Main Unit Into the Upper and the Lower Case Assembly 1. Remove the two screws holding the switch board. 2. Remove the switch board. 3. Disconnect the touchpad FFC from the main board. 4. Disconnect the bluetooth cable. 5. Remove the five screws that secure the upper case. 6. Remove the eighteen screws on the bottom as shown. 7. Detach the upper case assembly and place it next to the lower case assembly. 8.
Disassembling the Upper Case Assembly 1. Disconnect the touchpad board to touchpad FFC. 2. Disconnect the touchpad board to main board FFC. 3. Then detach the touchpad board to main board FFC from the touchpad board. 4. Remove the three screws that secure the touchpad board. 5. Remove the touchpad board from the upper case. 6. Disconnect the touchpad board to touchpad FFC. 7. Remove the touchpad board to touchpad FFC from the uppwer case assembly. 8.
Disassembling the Lower Case Assembly 1. Disconnect the MDC cable from the modem board. 2. Detach the MDC cable from the main board. 3. Remove the two screws holding the modem board. 4. Remove the modem board from the lower case. 5. Disconnect the speaker cable from the main board. 6. Remove the two screws that secure the main board. 7. Remove the two screw nuts as shown. 8. The you can detach the main board from the upper case. 9. Remove the three screws that secure the VGA heatsink. 10.
13. Then remove another two screws holding the speaker set on the other side. 14. Then take out the speaker set from the lower case. 56 Chapter 3 download service manual and resetter printer at http://printer1.blogspot.
Disassembling the LCD Module 1. Remove the four screw caps as shown. 2. Remove the four screws holding the LCD bezel. 3. Then detach the LCD bezel from the LCD module. 4. Disconnect the inverter board then remove it. 5. Remove the three screws holding the right hinge. 6. Then remove the three screws that secure the left hinge. 7. Remove one screw that secure the LCD bracket. 8. Remove another screw holding the LCD bracket on the other side. 9.
13. Remove the left bracket as the picture shows. 14. Tear off the tape fastening the LCD cable. 15. Tear off the the LCD cable fastening the LCD cable, then remove it.. 58 Chapter 3 download service manual and resetter printer at http://printer1.blogspot.
Disassembling the External Modules Disassembling the HDD Module 1. Remove the two screws holding the HDD bracket on one side. 2. Remove another two screws holding the HDD bracket on the other side. 3. Then take the hard disc drive out from the HDD bracket. Disassembling the Optical Drive Module 1. Remove the four screws as the picture shows. 2. Remove the two screws that secure the optical disc drive and the ODD holder. 3. Push the ODD holder as shown. 4. Detach the ODD holder. 5.
60 Chapter 3 download service manual and resetter printer at http://printer1.blogspot.
Chapter 4 Troubleshooting Use the following procedure as a guide for computer problems. NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1. Obtain the failing symptoms in as much detail as possible. 2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation.
System Check Procedures External Diskette Drive Check Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is required. NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause damage to the drive or cause the drive to fail. Do the following to select the test device. 1. Boot from the diagnostics diskette and start the diagnostics program. 2.
If any of these devices do not work, reconnect the cable connector and repeat the failing operation. Memory check Memory errors might stop system operations, show error messages on the screen, or hang the system. 1. Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board. 2. Go to the diagnostic memory in the test items. 3. Press F2 in the test items. 4. Follow the instructions in the message window.
2. In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total Battery Power Remaining are correct. 3. Repeat the steps 1 and 2, for both battery and adapter. 4. This helps you identify first the problem is on recharging or discharging. From Hardware: 1. Power off the computer. 2. Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground). See the following figure 3. If the voltage is still less than 7.
Power-on Self-Test Error Messages The POST error message index lists the error message and their possible causes. The most likely cause is listed first. NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU replacement does not solve the problem, put the original part back in the computer. Do not replace a non-defective FRU. This index can also help you determine the next possible FRU to be replaced when servicing a computer.
Index of Error Messages Error Code List Error Codes 006 Error Messages Equipment Configuration Error Causes: 1. CPU BIOS Update Code Mismatch 2. IDE Primary Channel Master Drive Error (THe causes will be shown before “Equipment Configuration Error”) 010 Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh) 070 Real Time Clock Error 071 CMOS Battery Bad 072 CMOS Checksum Error 110 System disabled. Incorrect password is specified.
Error Message List Error Messages Real time clock error FRU/Action in Sequence RTC battery Run BIOS Setup Utility to reconfigure system time, then reboot system. System board Previous boot incomplete - Default configuration used Run “Load Default Settings” in BIOS Setup Utility. RTC battery System board Memory size found by POST differed from CMOS Run “Load Default Settings” in BIOS Setup Utility.
Error Message List No beep Error Messages No beep, power-on indicator turns off and LCD is blank. FRU/Action in Sequence Power source (battery pack and power adapter). See “Power System Check” on page 63. Ensure every connector is connected tightly and correctly. Reconnect the DIMM. LED board. System board. No beep, power-on indicator turns on and LCD is blank. Power source (battery pack and power adapter). See “Power System Check” on page 63.
Phoenix BIOS Beep Codes Code Beeps POST Routine Description 02h Verify Real Mode 03h Disable Non-Maskable Interrupt (NMI) 04h Get CPU type 06h Initialize system hardware 08h Initialize chipset with initial POST values 09h Set IN POST flag 0Ah Initialize CPU registers 0Bh Enable CPU cache 0Ch Initialize caches to initial POST values 0Eh Initialize I/O component 0Fh Initialize the local bus IDE 10h Initialize Power Management 11h Load alternate registers with initial POST values 1
Code 46h Beeps 2-1-2-3 48h Check ROM copyright notice Check video configuration against CMOS 49h Initialize PCI bus and devices 4Ah Initialize all video adapters in system 4Bh QuietBoot start (optional) 4Ch Shadow video BIOS ROM 4Eh Display BIOS copyright notice 50h Display CPU type and speed 51h Initialize EISA board 52h Test keyboard 54h 58h 70 POST Routine Description Set key click if enabled 2-2-3-1 Test for unexpected interrupts 59h Initialize POST display service 5Ah Displa
Code Beeps POST Routine Description 8Ch Initialize floppy controller 8Fh Determine number of ATA drives (optional) 90h Initialize hard-disk controllers 91h Initialize local-bus hard-disk controllers 92h Jump to UserPatch2 93h Build MPTABLE for multi-processor boards 95h Install CD ROM for boot 96h Clear huge ES segment register 97h 98h Fixup Multi Processor table 1-2 Search for option ROMs. One long, two short beeps on checksum failure.
Code Beeps D2h Unknown interrupt E0h Initialize the chipset E1h Initialize the bridge E2h Initialize the CPU E3h Initialize the system timer E4h Initialize system I/O E5h Check force recovery boot E6h Checksum BIOS ROM E7h Go to BIOS E8h Set Huge Segment E9h Initialize Multi Processor EAh Initialize OEM special code EBh Initialize PIC and DMA ECh Initialize Memory type EDh Initialize Memory size EEh Shadow Boot Block EFh System memory test F0h Initialize interrupt vector
Index of Symptom-to-FRU Error Message LCD-Related Symptoms Symptom / Error LCD backlight doesn't work Action in Sequence LCD is too dark Enter BIOS Utility to execute “Load Setup Default Settings”, then reboot system. LCD brightness cannot be adjusted Reconnect the LCD connectors. LCD contrast cannot be adjusted Keyboard (if contrast and brightness function key doesn't work).
Power-Related Symptoms Symptom / Error Battery can’t be charged Action in Sequence See “Check the Battery Pack” on page 63. Battery pack System board PCMCIA-Related Symptoms Symptom / Error System cannot detect the PC Card (PCMCIA) Action in Sequence PCMCIA slot assembly System board PCMCIA slot pin is damaged. PCMCIA slot assembly Memory-Related Symptoms Symptom / Error Memory count (size) appears different from actual size.
Power Management-Related Symptoms Symptom / Error Battery fuel gauge in Windows doesn’t go higher than 90%. Action in Sequence Remove battery pack and let it cool for 2 hours Refresh battery (continue use battery until power off, then charge battery) Battery pack System board System hangs intermittently. Reconnect hard disk/CD-ROM drives. Hard disk connection board System board Peripheral-Related Symptoms Symptom / Error Action in Sequence System configuration does not match the installed devices.
Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: 76 1. Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRU. 3.
Undetermined Problems The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU). NOTE: Verify that all attached devices are supported by the computer. NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power System Check” on page 63): 1.
78 Chapter 4 download service manual and resetter printer at http://printer1.blogspot.
Chapter 4 Jumper and Connector Locations Top View Chapter 4 79 download service manual and resetter printer at http://printer1.blogspot.
Rear View ITEM 80 DESCRIPTION ITEM DESCRIPTION CN2 LCD Connector CN14 DC JACK CN3 LED board connector CN15 CRT connector SW2 Lid switch CN16 Docking connector CN10 express card connector CN17 Battery connector CN11 4 IN 1 connector CN18 Fix ODD connector CN13 Speaker connector CN21 Swap ODD connector CN9 MD board connector CN24 2nd Battery connector CN12 INT MIC connector CN30 PATA HDD connector Chapter 5 download service manual and resetter printer at http://printer1.
Chapter 5 ITEM DESCRIPTION ITEM CN5 Keyboard connector CN31 SATA HDD connector DESCRIPTION CN6 BT connector CN36 Line IN connector CN8 TP connector CN34 MIC IN connector U4 VGA RAM CN35 Line out/SPDIF connector U8 VGA RAM CN33 USB connector U6 LAN transformer CN32 1394 connector CN28 PCMCIA connector CN26 USB connector CN25 USB connector CN23 S video connector CN20 RJ45/RJ11 connector CN19 Fan connector CN22 MINI PCI connector U31 U30 EC U29 VGA Chp U34 North
RTC Jumper 82 Chapter 5 download service manual and resetter printer at http://printer1.blogspot.
Chapter 6 FRU (Field Replaceable Unit) List This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Aspire 1650. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide.
Exploded Diagram 84 Chapter 6 download service manual and resetter printer at http://printer1.blogspot.
Illustration Part Name Description Acer P/N Adapter ADAPTER 65W 3 PIN DELTA SADP-65KB BFD TBD AP.06501.005 ADAPTER 65W 3 PIN LITE-ON PA-1650-02 Q2 19V TBD AP.06503.006 ADAPTER 65W 3 PIN HIPRO HPOK066B13QT TBD AP.06506.001 BATTERY SANYO LIION 4S2P 4.4A 4UR18650F-2-QC140 ZL1A BATTERY (SANYO 8 CELL) S.P. BT.T5003.001 BATTERY PANASONIC LI-ION 4S2P 4.4A CGR-B/8B5AE ZL1A BATTERY (PANASONIC 8 CELL) S.P BT.T5005.001 BATTERY SIMPLO LIION 4S2P 4.4A 9163020 ZL1A BATTERY (SIMPLO 8 CELL) S.P. BT.
Illustration Part Name Description Acer P/N TOUCH PAD BOARD ZL1A TOUCH PAD BOARD ASSY S.P. 55.T50V7.002 FFC CABLE - TP/B TO MB ZL1A TOUCH PAD BOARD M/B (FFC) ASSY S.P. 50.T50V7.001 MODEM CABLE ZL1A MODEM CABLE ASSY S.P. 50.T50V7.002 POWER CORD US ET2S POWER CORD S/P-US 27.A03V7.001 ET2S POWER CORD S/P-PRC 27.A03V7.003 ZI1S POWER CORD SPARE PART-KOERA 27.T23V7.006 ET2S POWER CORD S/P-EU 27.A03V7.002 ET2S POWER CORD S/P-UK 27.A03V7.
Illustration Part Name Description Acer P/N LOWER CASE W/ SPEAKER W/O 1394 ZL3A BASE ASSY W/O 1394 S/P 60.TAHV7.001 UPPER CASE W/TP, BRACKET, MIC,BLUETOOTH CABLE W/O IR ZL2 TOP COVER TM ASSY W/O IR 60.TAHV7.002 DIMM/WIRELESS COVER ZL1 DDR COVER ASSY 42.T63V7.001 HEATSINK COVER ZL2 HEATSINK COVER W/O DOCKING ASSY 42.T66V7.001 3 IN 1 DUMMY COVER ZL1A 3 IN 1DUMMY COVER ASSY S.P. 42.T51V7.002 HDD COVER ZL2 HDD COVER ASSY 42.T63V7.004 HDD BRACKET ZL1A HDD BRACKET ASSY S.P. 33.T50V7.
Illustration 88 Part Name Description Acer P/N DVD/CDRW COMBO DRIVE 24X QSI SBW242C ZI6 COMBO SBW-242C S/P-QSI KO.02407.014 OPTICAL DEVICE CONNECTOR BOARD W/MYLARY ZL1 CD ROM/B ASSY S.P. 55.T50V7.003 OPTICAL DEVICE HOLDER-SWAP ZL1 DVD HOLDER ASSY S.P. 42.T50V7.007 DVD/CDRW BEZEL FOR QSI ZL1A COMBO BEZEL (QSI) ASSY S.P. 42.T50V7.008 DVD/CDRW COMBO MODULE KME UJDA760 SWAP ZL1 COMBO (KME UJDA-760) W/MB ASSY S.P. 6M.T50V7.002 DVD/CDRW COMBO DRIVE 24X KME UJDA760 ZL1A COMBO (KME UJDA-760) S.
Illustration Part Name Description Acer P/N DVD DUAL DRIVE LIET-ON SOSW-833 DL G BASE ZL6 DVD RW(DUAL) SOSW-833S S.P. KU.00804.012 OPTICAL DEVICE CONNECTOR BOARD W/MYLARY ZL1 CD ROM/B ASSY S.P. 55.T50V7.003 OPTICAL DEVICE HOLDER-SWAP ZL1 DVD HOLDER ASSY S.P. 42.T50V7.007 DVD DUAL BEZEL FOR LITE-ON ZL1A DVD DUAL BEZEL (LITON) ASSY S.P. 42.T50V7.012 Toshiba PLUTO 40G 4200rpm MK4025GAS ,KA100A F/W:KA100A Toshiba PLUTO 40G 4200rpm MK4025GAS ,KA100A F/W:KA100A KH.04004.
Illustration Part Name Description Acer P/N Keyboard 90 TM4500/TM4000/ TM2300 KEYBOARD DARFON US International ZL1A K/B EUGO-U/I ASSY S.P. KB.T5007.001 TM4500/TM4000/ TM2300 KEYBOARD DARFON Chinese ZL1A K/B ERGOTAIWAN ASSY S.P. KB.T5007.002 TM4500/TM4000/ TM2300 KEYBOARD DARFON Spanish ZL1A K/B EUGOSPANISH ASSY S.P. KB.T5007.003 TM4500/TM4000/ TM2300 KEYBOARD DARFON Thai ZL1A K/B EUGO-THAI ASSY S.P. KB.T5007.
Illustration Part Name Description Acer P/N TM4500/TM4000/ TM2300 KEYBOARD DARFON Norway ZL1A K/B EUGONORWAY ASSY S.P. KB.T5007.018 TM4500/TM4000/ TM2300 KEYBOARD DARFON Danish ZL1A K/B EUGODANISH ASSY S.P. KB.T5007.019 TM4500/TM4000/ TM2300 KEYBOARD DARFON Turkish ZL1A K/B EUGOTURKISH ASSY S.P. KB.T5007.020 TM4500/TM4000/ TM2300 KEYBOARD DARFON Canadian French ZL1A K/B EUGO-CANA FREN ASSY S.P. KB.T5007.021 TM4500/TM4000/ TM2300 KEYBOARD DARFON Japanese ZL1A K/B EUGOJAPAN ASSY S.P. KB.
Illustration 92 Part Name Description Acer P/N LCD MODULE 15 IN. SXGA AU B150PG03 LIGHT GREEN SILVER ZL1 15" LCD SXGA+ (TM-AU) ASSY S.P. NEW COLOR 6M.T63V7.011 LCD 15" TFT SXGA+ AU B150PG03 (NOVATEC) ZI1S 15" SXGA+ LCD PANEL S/P-AU LK.15005.008 LCD INVERTER BOARD ZL1A LCD INVERTER ASSY S.P. 19.T50V7.001 LCD CABLE - 15 IN. XGA ZL1A 15" LCD CABEL XGA ASSY S.P. 50.T50V7.004 LCD BRACKET W/ HINGE 15 IN. - L ZL1A 15" LCD HINGE (L) ASSY S.P. 33.T50V7.002 LCD BRACKET W/ HINGE 15 IN.
Illustration Part Name Description Acer P/N LCD MODULE 15.4 IN. WXGA QDI QD15TL0201-LIGHT GREEN SILVER ZL1A 15.4" LCD WXGA (TM QDI) ASSY S.P. NEW COLOR 6M.T50V7.029 LCD 15.4 IN. WXGA QDI QD15TL02-01 ZL1A 15.4" LCD (QDI) PANEL ASSY S.P. LK.15409.001 LCD INVERTER BOARD ZL1A LCD INVERTER ASSY S.P. 19.T50V7.001 LCD CABLE - 15.4 IN. WXGA ZL1A 15.4" LCD WXGA CABEL ASSY S.P. 50.T50V7.006 LCD BRACKET W/ HINGE 15.4 IN. - L ZL1A 15.4" LCD HINGE (L) ASSY S.P. 33.T50V7.004 LCD BRACKET W/ HINGE 15.
Illustration 94 Part Name Description Acer P/N LCD MODULE 15.4 IN. WXGA CMO N154I1L09 V.C2-LIGHT GREEN SILVER ZL2 15.4" LCD WXGA (TM CMO) ASSY S.P. NEW COLOR 6M.T63V7.013 LCD 15.4 IN. WXGA CMO N154I1-L09 V.C2 ZL2 15.4" LCD (CMO) PANEL ASSY S.P. LK.1540D.003 LCD INVERTER BOARD ZL1A LCD INVERTER ASSY S.P. 19.T50V7.001 LCD CABLE - 15.4 IN. WXGA ZL1A 15.4" LCD WXGA CABEL ASSY S.P. 50.T50V7.006 LCD BRACKET W/ HINGE 15.4 IN. - L ZL1A 15.4" LCD HINGE (L) ASSY S.P. 33.T50V7.
Illustration Part Name Description Acer P/N LCD MODULE 15.4 IN. WXGA HITACHI TX39D85VC1FAALIGHT GREEN SILVER ZL1A 15.4" LCD WXGA (TM HITACHI) ASSY S.P. NEW COLOR 6M.T63V7.015 LCD 15.4 IN. WXGA HITACHI TX39D85VC1FAA ZL2 15.4" LCD (HITACHI) PANEL ASSY S.P. LK.15404.003 LCD INVERTER BOARD ZL1A LCD INVERTER ASSY S.P. 19.T50V7.001 LCD CABLE - 15.4 IN. WXGA ZL1A 15.4" LCD WXGA CABEL ASSY S.P. 50.T50V7.006 LCD BRACKET W/ HINGE 15.4 IN. - L ZL1A 15.4" LCD HINGE (L) ASSY S.P. 33.T50V7.
Illustration Part Name Description Acer P/N SO-DIMM DDR333 512MB UNIFOSA U30512AAUIQ652AW2 0 SO-DIMM DDR333 512MB UNIFOSA U30512AAUIQ652AW2 0 KN.5120H.001 MEMORY DDR333 1GB ELPIDA EBD11UD8ADDA SO-DIMM DDR333 1GB ELPIDA EBD11UD8ADDA KN.1GB09.002 SPEAKER SET ZL1A SPEAKER ASSY S.P. 23.T50V7.001 THERMAL MODULE ZL2 CPU HEATSINK ASSY 60.T63V7.003 VGA HEATSINK FOR DISCRETE W/PAD ZL2 SINK VGA ASSY W/ NB 34.T63V7.001 VGA HEATSINK FOR DISCRETE W/PAD ZL2 SINK VGA ASSY W/ NB 34.T63V7.
Illustration Part Name Description Acer P/N SCREW M2.5*4L-BZNNYLOK ET2S SCREW MM2.5X4.0 SPARE PART 86.A03V7.006 SCREW M2.0X5-I-NINYLOK ZI1S SCREW M2.0X5-INI-NYLOK S/P 86.T23V7.006 SCREW MM25060IL69 DT1 SCREW MM25060IL69 SPARE PART 86.A08V7.004 SCREW M2.0*5I(NI)(NYLOK) ZI1S SCREW M2.5X5.0-I-NI-NYLOK S/P 86.T23V7.010 SCREW M2.0X2.5-I-NINYLOK ET2S SCREW MM2.0X2.5 SPARE PART 86.A03V7.007 SCREW I2*3M-NIHY (M2L3) ZG1S I2*3M-NIHY (M2L3) S/P 86.T25V7.008 SCREW M1.7*3.0-I (BK) ZL1A SCREW (M1.
98 Chapter 6 download service manual and resetter printer at http://printer1.blogspot.
