Acer Projektor X1161/X1161A/X110/X1161N/X1261 Serie Benutzerhandbuch
Copyright © 2009. Acer Incorporated. Alle Rechte vorbehalten. Acer Projektor X1161/X1161A/X110/X1161N/X1261-Reihe Benutzerhandbuch Erste Ausgabe: 10/2009 Gelegentliche Änderungen der Informationen in dieser Veröffentlichung behalten wir uns ohne Ankündigung vor. Diese Änderungen werden jeweils in die folgenden Ausgaben dieses Handbuchs, zusätzlicher Dokumente oder Veröffentlichungen übernommen.
iii Informationen für Ihre Sicherheit und Komfort Lesen Sie sorgfältig diese Anweisungen. Heben Sie das Dokument für einen späteren Gebrauch auf. Befolgen Sie alle auf dem Produkt befindlichen Warnungen und Anweisungen. Vor dem Reinigen das Gerät ausschalten Trennen Sie vor dem Reinigen das Gerät vom Netz. Verwenden Sie keine flüssigen Reinigungsmittel oder Spritzreinigungsmittel. Reinigen Sie das Gerät nur mit einem angefeuchteten Tuch.
iv • • Stellen Sie das Gerät nicht auf eine vibrierende Oberfläche, um Schäden an internen Komponenten und ein Leck der Batterien zu vermeiden. Verwenden Sie das Gerät nicht in einer Sport-, Übungs- oder vibrierenden Umgebung, da ein unerwarteter Kurzschluss oder Schaden an Ankern oder Lampen die Folge sein kann. Auf die Stromversorgung achten • • • • • Die Stromversorgung des Gerätes muss mit der Angabe auf dem Typenschild übereinstimmen.
v Instandsetzen des Produkts Versuchen Sie niemals das Produkt in eigener Regie zu reparieren. Durch Öffnen des Gehäuses setzen Sie sich Hochspannung und anderen Gefahren aus. Überlassen Sie die Reparatur qualifiziertem Kundendienstpersonal.
vi • • • • • • • • • • • • • • • • • • Schlag kann die Folge sein. Trennen Sie in diesem Fall unverzüglich den Projektor vom Netz und nehmen Kontakt mit Ihrem Händler auf. Verwenden Sie das Gerät nicht weiter, wenn es zerbrochen ist oder heruntergefallen ist. Nehmen Sie in diesem Fall Kontakt mit Ihrem Händler für eine Untersuchung auf. Richten Sie das Projektorobjektiv nicht auf die Sonne. Ein Brand kann die Folge sein.
vii Vorsicht mit dem Gehör Folgen Sie bitte den nachstehenden Anweisungen, um Ihr Gehör zu schützen. • • • • • Erhöhen Sie schrittweise die Lautstärke, bis Sie deutlich und gemütlich hören können. Erhöhen Sie die Lautstärke nicht weiter, wenn Ihre Ohren sich an die Lautstärke gewöhnt haben. Hören Sie Musik nicht über längere Zeit bei einer hohen Lautstärke. Versuchen Sie nicht mit einer erhöhten Lautstärke laute Umgebungen zu übertönen.
viii Das allererste Benutzungshinweise Was Sie tun sollten: • • Schalten Sie vor dem Reinigen das Gerät aus. • Trennen Sie das Gerät vom Stromnetz, wenn es über einen längeren Zeitraum nicht benutzt wird. Verwenden Sie zur Reinigung des Gehäuses ein weiches, mit mildem Reinigungsmittel angefeuchtetes Tuch. Was Sie nicht tun sollten: • Blockieren Sie niemals die Lüftungsöffnungen des Gerätes, da sie zur Kühlung dienen. • Benutzen Sie zur Reinigung keine Scheuermittel, Wachse oder Lösungsmittel.
Das allererste iii viii Benutzungshinweise viii Vorsichtsmaßnahmen viii Einführung 1 Produktmerkmale 1 Lieferumfang 2 Überblick über den Projektor 3 Aussehen des jektors 3 Fernbedienung und Bedienfeld Layout 5 Inbetriebnahme 7 Anschließen des Projektors 7 Ein-/Ausschalten des Projektors 8 Einschalten des Projektors 8 Ausschalten des Projektors 9 Einstellen des Projektionsbildes 10 Einstellen der Höhe des Projektionsbildes 10 So optimieren Sie die Bildgröße und Entfernung 11
Anhang 26 Fehlerbehebung 26 Liste mit LED- und Alarm-Definitionen 30 Auswechseln der Lampe 31 Deckenmontage 32 Technische Daten 35 Kompatible Modi 37 Bestimmungen und Sicherheitshinweise 39
1 Produktmerkmale Für diesen Projektor wurde die Singlechip-DLP® Technologie verwendet.
Deutsch 2 Lieferumfang Die folgenden Artikel gehören zum Lieferumfang des Projektors. Bitte prüfen Sie die Vollständigkeit des Produkts. Wenden Sie sich umgehend an Ihren Händler , falls irgendein Artikel fehlt.
3 Deutsch Überblick über den Projektor Aussehen des jektors Frontseite/ Oberseite 1 7 8 3 2 9 3 1 4 10 5 6 # 1 2 3 4 5 Beschreibung # Belüftung (Luftzufuhr) Belüftung (Luftaustritt) Fernbedienungsempfänger Fokusring Zoomobjektiv 6 7 8 9 10 Rückseite Beschreibung Objektivabdeckung Stromschalter Fernbedienung Zoomregler Lautsprecher 7* 10 6* 1 3 4 5 7 10* 8 9 2
Deutsch 4 # Beschreibung X1161N-Serie: 1 Netzanschluss 2 Anschluss für Kensington™-Schloss 3 PC-Analogsignaleingang (VGA-Eingang 1 oder VGA-Eingang) # Beschreibung 10 USB-Anschluss X1261-Serie: 1 Netzanschluss 2 Anschluss für Kensington™-Schloss PC-Analogsignal-/HDTV-/ 3 Component-Videoeingang (VGA-Eingang 1 oder VGA-Eingang) 4 S-Videoeingang Nur bei X1161/X1161A/X110: 5 1 Netzanschluss 2 Anschluss für Kensington™-Schloss PC-Analogsignal-/HDTV-/Component3 Videoeingang 4 S-Videoeingang 5 Compos
5 2 1 8 3 9 8 4 # 1 2 Symbol 5 6 10 11 7 12 2 13 Funktion Beschreibung Fernbedienungs Dieser empfängt die Signale von der Fernbedienung. empfänger Stromschalter Siehe Beschreibung im Abschnitt "Ein-/Ausschalten des Projektors". MENU • 9 Vier Pfeiltasten 10 ZOOM 11 SOURCE Verwenden Sie diese Pfeiltasten, um Elemente auszuwählen oder Einstellungen zu ändern. Mit dieser Taste zoomen Sie das projizierte Bild ein oder aus. Damit schalten Sie die aktive Quelle um.
Deutsch 6 # Symbol Funktion 12 HIDE 13 EmpoweringTaste Beschreibung Mit dieser Taste deaktivieren Sie vorübergehend die Videowiedergabe. Drücken Sie auf "HIDE", um das Bild auszublenden. Drücken Sie erneut auf diese Taste, um das Bild wieder anzuzeigen. Einmalige Acer-Funktionen: eView, eTimer, ePower Management. Hinweis: Anbringen der Fernbedienung Bitte beziehen Sie sich auf die Abbildung, um die Fernbedienung an dem Projektor anzubringen.
7 Deutsch Inbetriebnahme Anschließen des Projektors VGA RS232 RS232 USB USB D-Sub 8 D-Sub 8 USB 4 X1161 Serie 2 4 USB 2 D-Sub 6 D-Sub Y 1 3 7 5 R W Y S-Videoausgabe Videoausgabe # Beschreibung # Beschreibung X1161N-Serie: X1261-Serie: 1 Netzkabel 1 2 VGA-Kabel 2 VGA-Kabel 8 USB-Kabel 3 Composite-Videokabel Netzkabel X1161-/X1161A/X110-Serie: 4 RS232-Kabel 1 Netzkabel 5 S-Videokabel 2 VGA-Kabel 6* 3 Composite-Videokabel 5 S-Videokabel 8 USB-Kabel 4*
Deutsch 8 Ein-/Ausschalten des Projektors Einschalten des Projektors 1 Entfernen Sie die Linsenkappe (Abbildung #1). 2 Stellen Sie sicher, dass das Netzkabel und das Signalkabel richtig verbunden sind. Die Betriebs-LED blinkt daraufhin rot. 3 Schalten Sie den Projektor durch Drücken des "Power (Ein/Aus)" am Bedienfeld ein. Die Betriebs-LED leuchtet daraufhin blau. (Abbildung #2) 4 Schalten Sie die Signalquelle (Computer, Notebook, Videowiedergabegerät usw.) ein.
9 1 Drücken Sie zweimal die Taste "Power (Ein/Aus)", um den Projektor auszuschalten. Die folgende Nachricht wird für ca. 5 Sekunden angezeigt. "Bitte erneut den Stromschalter drücken, um den Abschaltvorgang abzuschließen." 2 Nach dem Starten des Ausschaltvorgangs blinkt die Betriebs-LED schnell rot und das Gebläse arbeitet weiterhin für ungefähr 120 Sekunden. Dies stellt sicher, dass das System richtig abgekühlt wird.
Deutsch 10 Einstellen des Projektionsbildes Einstellen der Höhe des Projektionsbildes Der Projektor hat höhenverstellbare Füße, mit denen die Höhe des Projektionsbildes eingestellt werden kann. Projektionsbild anheben/absenken: 1 Mit Hilfe der Winkelverstellfüße (Abbildung #1) können Sie die Feineinstellung vornehmen.
11 Sehen Sie in der nachstehenden Tabelle nach, um die möglichen optimalen Bildgrößen in Abhängigkeit der Entfernung des Projektors von der Leinwand zu finden. indem Sie z.B. auf Wenn der Projektor z.B. 3 m von der Leinwand entfernt ist, dann ist eine gute Bildqualität mit den Bildgrößen von 69 bis zu 76 Zoll möglich. Hinweis: Wie in der folgenden Abbildung angezeigt ist ein Raum mit der Höhe von mindestens 133 cm erforderlich, wenn der Projektor 3 m von der Leinwand entfernt steht.
Deutsch 12 Bildgröße Oben Bildgröße Oben (Min. Zoomfaktor) (Max.
13 Die folgende Tabelle zeigt an, wie Sie eine gewünschte Bildgröße durch Justieren der Projektorposition oder durch Verwenden des Zoomrings erreichen. indem Sie z.B. auf Um eine Bildgröße von 50 Zoll zu erhalten, stellen Sie den Projektor in einer Entfernung von 2 bis 2,2m von der Leinwand auf und justieren Sie entsprechend den Zoomfaktor.
Deutsch 14 Gewünschte Bildgröße Diagonal (Zoll) B (cm) x H (cm) 30 61 x 46 Entfernung (m) Oben (cm) Von der Grundlinie bis Max. Min.
15 Installationsmenü Es steht Ihnen ein OSD-Installationsmenü für die Installation und Wartung des Projektors zur Verfügung. Verwenden Sie nur dann diese OSD-Funktion, wenn die Meldung "Kein Signal" auf dem Bildschirm erscheint. Durch das Menü können Sie die Leinwandgröße, die Entfernung, den Fokus, die Trapezkorrektur usw. einstellen bzw. anpassen. 1 Setzen Sie den Projektor durch Drücken der Taste "Ein/Aus" am Bedienfeld in Betrieb.
Deutsch 16 Acer Empowering Technologie Empowering-Taste Die Acer Empowering-Taste bietet drei von Acer entwickelte, einmalige Funktionen: "Acer eView Management", "Acer eTimer Management" und "Acer ePower Management". Drücken Sie auf die Taste " " für länger als eine Sekunde, um das OSD-Hauptmenü zu öffnen und damit die Funktion zu modifizieren. Acer eView Management Drücken Sie auf " ", um das Untermenü "Acer eView Management" zu öffnen.
17 Der Projektor hat mehrsprachige OSD-Menüs, mit denen Sie Bildeinstellungen vornehmen und Parameter verändern können. Verwenden der OSD-Menüs • Um das OSD-Menü zu öffnen, drücken Sie "MENÜ" auf der Fernbedienung. • Im OSD-Hauptmenü können Sie mit Hilfe der Tasten ein Element auswählen. Nachdem Sie ein gewünschtes Element aus dem Hauptmenü gewählt haben, drücken Sie bitte auf , um das entsprechende Untermenü für die Funktionseinstellung zu öffnen.
Deutsch 18 Farbe Anzeigemodus Hier finden Sie einige für verschiedene Bildtypen optimal angepasste Werkseinstellungen. • • • • • • Standard: Für normale Umgebung. Video: Für Videowiedergaben in einer hellen Umgebung. Hell: Für optimale Helligkeit. Bild: Für Grafiken. Spiel: Für Spiele. Benutzer: Benutzerdefinierte Einstellungen. Wandfarbe Hier wählen Sie eine der Wand entsprechende Farbe aus. Es stehen Ihnen die Optionen Weiß, Hellgelb, Hellblau, Rosa und Dunkelgrün zur Auswahl.
19 Hier können Sie ein Videobild von schwarzweiß bis vollfarbig einstellen. Farbton • Drücken Sie auf verringern. , um den Anteil der Farbe in dem Bild zu • Drücken Sie auf erhöhen. , um den Anteil der Farbe in dem Bild zu Hier können Sie die Balance der Farben Rot und Grün einstellen. • Drücken Sie auf , um den Anteil der grünen Farbe in dem Bild zu erhöhen. • Drücken Sie auf Bild zu erhöhen.
Deutsch 20 Seitenverhältnis Hier wählen Sie ein bevorzugtes Seitenverhältnis aus. • Autom.: Diese Option behält das originale Seitenverhältnis des Bildes und maximiert das Bild, um es an den physikalischen horizontalen oder vertikalen Pixeln anzupassen. • 4:3: Das Bild wird an der Leinwand angepasst, skaliert und mit einem Seitenverhältnis von 4:3 angezeigt. • 16:9: Das Bild wird an der Breite der Leinwand angepasst, skaliert und mit einem Seitenverhältnis von 16:9 angezeigt. Autom.
21 " - Funktionen werden vom X1161A/X110/ Hinweis: "Projektionsort --> X1161N nicht unterstützt. Hinweis: Die 3D-Funktion ist nur im Fall einer VGA-Quelle verfügbar. Sehen Sie bitte in der Frequenztabelle für die 3D-Frequenzen nach. Hinweis: Wenn Sie NVIDIA 3D Vision benutzen, laden Sie bitte die aktuellste Version des NVIDIA 3D VISION-Treibers für Ihre Grafikkarte von der NVIDIAWebsite herunter und installieren Sie diese, damit die Grafikkarte den Projektor unterstützt.
Deutsch 22 Einstellung Menü-Pos. Hier stellen Sie die Position des Menüs auf dem Bildschirm ein. Quellen festlegen Der Projektor sucht nach anderen Signalen, wenn das momentane Eingabesignal verloren gegangen ist und die Quellenverriegelung auf "Aus" gestellt ist. Wenn die Quellenverriegelung auf "Ein" gestellt ist, wird der aktuelle Quellkanal "verriegelt", bis Sie die Taste "Source" auf der Fernbedienung für den nächsten Kanal drücken. Verd. Untertitel Sie können einen bevorzugten "Verd.
23 • Drücken Sie auf , um das "Benutzerkennwort" einzurichten oder zu ändern. • Stellen Sie mit Hilfe der Nummerntasten auf der Fernbedienung Ihr Kennwort ein und drücken anschließend auf "MENU", um Ihre Einstellung zu bestätigen. • • Drücken Sie auf • • Das Kennwort sollte 4 bis 8 Zeichen haben. • Wenn die Option "Kennwort bei jedem Einschalten des Projektors abfragen" aktiviert ist, wird die Eingabe des Kennworts bei jedem Einschalten des Projektors verlangt. , um Zeichen zu löschen.
Deutsch 24 Verwaltung ECO-Modus Wählen Sie „Ein“, um die Projektorlampe zu dämpfen und damit den Stromverbrauch zu reduzieren, die Lampenlebensdauer zu verlängern und Rauschen zu reduzieren. Wählen Sie „Aus“, um in den Normalmodus zu wechseln. Große Höhe Wählen Sie "Ein", um den Modus Große Höhe zu aktivieren. Das Gebläse wird ununterbrochen mit voller Geschwindigkeit betrieben, um eine ausreichende Abkühlung des Projektors in großer Höhe sicherzustellen.
25 Deutsch Timer Timer-Ort • Hier stellen Sie die Position des Timers auf dem Bildschirm ein. Timer-Start • Drücken Sie auf beenden. , um den Timer zu starten oder zu Timer-Intervall • Drücken Sie auf oder , um die Timer-Periode oder , um den Timer- einzustellen. Timer-Anzeige • Drücken Sie auf Anzeigemodus einzustellen. Sprache Sprache Das OSD-Menü kann in verschiedenen Sprachen angezeigt werden. Drücken Sie auf oder , um eine bevorzugte Sprache auszuwählen.
Deutsch 26 Anhang Fehlerbehebung Falls Probleme mit dem Acer Projektor auftreten, sehen Sie bitte in der folgenden Fehlerbehebungsanleitung nach. Wenden Sie sich bitte an Ihren Händler oder das nächstgelegene Kundendienstzentrum, wenn Ihr Problem sich nicht beseitigen lässt.
27 4 Bild nur teilweise, rollend oder falsch angezeigt (Bei Notebooks) Der Bildschirm des NotebookComputers zeigt die Präsentation nicht an. • • Drücken Sie "RESYNC" auf der Fernbedienung. • Wenn Sie Probleme bei der Änderung der Auflösung haben oder das Bild am Monitor hängen bleibt, sollten Sie alle Geräte inklusive des Projektors neu starten.
Deutsch 28 9 10 11 Bild zu klein oder zu groß Das Bild hat schräge Seiten Das Bild ist falsch herum. • Justieren Sie den Zoomregler an der Vorderseite des Projektors. • Rücken Sie den Projektor näher an die Leinwand oder weiter von der Leinwand weg. • Drücken Sie "MENU" auf der Fernbedienung. Öffnen Sie "Bild --> Bildseitenverhältnis" und versuchen Sie verschiedene Einstellungen oder drücken Sie "Bildseitenverhältnis" auf der Fernbedienung, um die Einstellung direkt vorzunehmen.
29 # 1 Zustand Meldung Lösung Gebläse versagt - Das Systemgebläse funktioniert nicht. Projektor überhitzt - Die empfohlene Betriebstemperatur des Projektors wurde überschritten. Der Projektor muss abgekühlt werden, bevor er weiter verwendet werden darf. Lampe auswechseln - Die Lampe erreicht bald seine Standzeit. Bereiten Sie sich vor, sie bald auszuwechseln.
Deutsch 30 Liste mit LED- und Alarm-Definitionen LED-Meldungen Betriebs-LED Meldung Rot Blau Blinkt EIN bis AUS 100ms -- Standby V -- Ein-/Ausschalter EIN -- V Lampen-Neuversuch -- Schnell blinkend Schnell blinkend -- V -- Netzanschluss Ausgeschaltet (Abkühl-Modus) Ein-/Ausschalter AUS: Abkühlung abgeschlossen; Standby-Modus Fehler (Überhitzung) Abwechselnds rotes Blinken und blaues Leuchten Fehler (Gebläse festgeklemmt) Abwechselnds rotes Blinken und blaues Leuchten Fehler (Lampe ve
31 Entfernen Sie mit Hilfe eines Schraubenziehers die Schrauben am Deckel. Ziehen Sie anschließend die Lampe heraus. Der Projektor erkennt automatisch die Betriebszeit der Lampe. Wenn das Ende der Lampenlebensdauer naht, wird die Meldung "Das Ende der Lampenstandzeit wird im Vollleistungsbetrieb bald erreicht. Bitte ersetzen! auf dem Bildschirm angezeigt. Wechseln Sie bitte schnellstmöglich die Lampe aus, wenn Sie diese Meldung sehen.
Deckenmontage Möchten Sie den Projektor mit einer Deckenmontagevorrichtung installieren, dann folgen Sie bitte den nachstehenden Schritten: Bohren Sie vier Löcher in eine solide, massive Stelle an der Decke und bringen dann die Montageplatte an. m m m 13 m 20 1 Hinweis: Die Schrauben werden nicht mitgeliefert. Bitte kaufen Sie die für Ihre Decke geeigneten Schrauben. 2 Bringen Sie mit vier passenden Schrauben die Stange an.
33 Verwenden Sie so viele Schrauben, wie es für die Projektorgröße angemessen ist, um den Projektor an dem Halteblech zu befestigen. Hinweis: Es ist ratsam einen angemessenen Abstand zwischen dem Halteblech und dem Projektor zu halten, um eine ausreichende Wärmezerstreuung zu gewährleisten. Verwenden Sie gegebenenfalls zwei Unterlegscheiben zur zusätzlichen Unterstützung. 4 Bringen Sie das Halteblech an der Stange an.
5 Verstellen Sie gegebenenfalls den Winkel und die Position. Hinweis: In der folgenden Tabelle finden Sie den passenden Schrauben- und Unterlegschreibentyp für jedes Modell. Schrauben mit einer Durchmesser von 3 mm sind in der Schraubentüte beigelegt. Modelle X1161/X1161A/X110/ X1161N/X1261 Schraubentyp B Unterlegscheibentyp Durchmesser (mm) Länge (mm) Groß Klein 3 25 V V SCHRAUBENSPEZ.
35 Die nachstehenden technischen Daten können ohne Ankündigung geändert werden. Die endgültigen technischen Daten entnehmen Sie bitte den von Acer für den Vertrieb veröffentlichen Angaben.
Deutsch 36 E/A-Anschlüsse X1161N Reihe: • Netzanschluss x1 • • VGA-Anschluss x1 • • • • VGA-Anschluss x1 • • • • • • VGA-Anschluss x1 • • • • • • • • • Netzkabel x1 USB x1: für Fern-Computersteuerung X1161/X1161A/X110 Reihe: • Netzanschluss x1 USB x1: für Fern-Computersteuerung Composite Video x1 S-Video x1 X1261 Reihe: • Netzanschluss x1 Standardlieferumfang RS232 x1 Composite Video x1 S-Video x1 VGA-Ausgang x1 3,5mm Audioeingang x1 VGA-Kabel x1 Composite-Videokabel x1 (X1161/X1261 Reihe) Fer
37 Deutsch Kompatible Modi A. VGA analog 1 VGA analog - PC-Signal Modi VGA SVGA XGA SXGA QuadVGA SXGA+ UXGA Power Mac G4 PowerBook G4 Auflösung 640x480 640x480 640x480 640x480 640x480 800x600 800x600 800x600 800x600 800x600 800x600 1024x768 1024x768 1024x768 1024x768 1024x800 1152x864 1152x864 1152x864 1280X1024 1280X1024 1280X1024 1280X1024 1280x960 1280x960 1400x1050 1600x1200 640x480 800x600 1024x768 1152x870 1280x960 640x480 640x480 800x600 1024x768 V.
Deutsch 38 i Mac DV (G3) 2 1152x870 1280x960 1024x768 75 75 75 68,7 75,2 60,3 VGA analog - erweiterte Breitbild-Frequenz Modi WXGA Auflösung 1280x768 1280x768 1280x768 1280x720 1280x800 1440x900 WSXGA+ 1680x1050 1366x768 1920x1080-RB Horizontale Scanrate: Vertikale Scanrate: Max. Pixelrate V.Frequenz [Hz] H.
39 FCC-Erklärung Dieses Gerät wurde geprüft und hat sich als mit den Grenzwerten für ein Digitalgerät der Klasse B gemäß Teil 15 der Bestimmungen der amerikanischen Bundesbehörde für das Fernmeldewesen FCC (Federal Communications Commission) konform erwiesen. Diese Grenzwerte geben einen angemessenen Schutz gegen schädliche Funkstörungen innerhalb von Wohngebäuden.
Deutsch 40 Remarque à l'intention des utilisateurs canadiens Cet appareil numérique de la classe B est conforme a la norme NMB-003 du Canada. Konformitätserklärung für EU-Länder Hiermit erklärt Acer, dass diese Projektor-Reihe die Anforderungen und weiteren relevanten Bestimmungen der Richtlinie 1999/5/EG erfüllt.
Acer Incorporated 8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih Taipei Hsien 221, Taiwan Declaration of Conformity We, Acer Incorporated 8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih, Taipei Hsien 221, Taiwan Contact Person: Mr. Easy Lai, e-mail:easy_lai@acer.com.
Acer Incorporated 8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih Taipei Hsien 221, Taiwan The standards listed below are applied to the product if built with WLAN module or wireless keyboard and mouse. R&TTE Directive 1999/5/EC as attested by conformity with the following harmonized standard: z Article 3.1(a) Health and Safety -. EN60950-1 -. EN62311 z Article 3.1(b) EMC -. EN301 489-1 -. EN301 489-17 z Article 3.2 Spectrum Usages -. EN300 328 -. EN301 893 (Applicable to 5GHz high performance RLAN).
Acer America Corporation 333 West San Carlos St., San Jose CA 95110, U. S. A. Tel : 254-298-4000 Fax : 254-298-4147 www.acer.com Federal Communications Commission Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.