Acer Projector P5403/N243/PN-SX12/S5201M/ T111B/PS-X11M Series User's Guide
Copyright © 2010. Acer Incorporated. All Rights Reserved. Acer Projector P5403/N243/PN-SX12/S5201M/T111B/PS-X11M Series User's Guide Original Issue: 07/2010 Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications.
iii Information for Your Safety and Comfort Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. Turning the product off before cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
iv • • To avoid damage of internal components and to prevent battery leakage, do not place the product on a vibrating surface. Never use it under sporting, exercising, or any vibrating environment which will probably cause unexpected short current or damage rotor devices, lamp. Using electrical power • • • • • This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.
v Product servicing Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel.
vi • • • • • • • • • • • • • • • • • • might cause fire or electric shock. In this case, unplug immediately and contact your dealer. Do not keep using this product to break or drop it. In this case contact your dealer for inspection. Do not face the projector lens to the sun. It can lead to fire. When switching the projector off, please ensure the projector completes its cooling cycle before disconnecting power. Do not turn off the main power abruptly or unplug the projector during operation.
vii Caution for Listening To protect your hearing, follow these instructions. • • • • • Increase the volume gradually until you can hear clearly and comfortably. Do not increase the volume level after your ears have adjusted. Do not listen to music at high volumes for extended periods. Do not increase the volume to block out noisy surroundings. Decrease the volume if you can't hear people speaking near you. Disposal instructions Do not throw this electronic device into the trash when discarding.
viii First Thing First Usage Notes Do: • Turn off the product before cleaning. • Use a soft cloth moistened with mild detergent to clean the display housing. • Disconnect the power plug from AC outlet if the product is not being used for a long period of time. Don't: • Block the slots and openings on the projector provided for ventilation. • Use abrasive cleaners, waxes or solvents to clean the unit. • Use under the following conditions: • • • • In extremely hot, cold or humid environments.
First Thing First iii viii Usage Notes viii Precautions viii Introduction 1 Product Features 1 Package Overview 2 Projector Overview 3 Projector Outlook 3 Control Panel 4 Remote Control Layout 5 Getting Started Connecting the Projector Turning the Projector On/Off 7 7 9 Turning On the Projector 9 Turning Off the Projector 10 Adjusting the Projected Image 11 Adjusting the Height of the Projected Image 11 How to Optimize Image Size and Distance 12 How to Get a Preferred Image S
Troubleshooting 34 LED & Alarm Definition Listing 38 Replacing the Lamp 39 Ceiling Mount Installation 40 Specifications 43 Compatibility Modes 45 Regulations and safety notices 49
1 Product Features This product is a single-chip DLP® projector, including the following outstanding features: • DLP® technology • S5201M/T111B/PS-X11M: Native 1024 x 768 XGA resolution P5403/N243/PN-SX12: Native 1400 x 1050 SXGA+ resolution 4:3 / 16:9 aspect ratio supported • Acer ColorBoost technology delivers vivid, life-like images • High brightness and contrast ratio • Versatile display modes enable optimum performance in any situation • NTSC/PAL/SECAM compatible and HDTV (720p, 1080i) sup
English 2 Package Overview This projector comes with all the items shown below. Check to make sure you have them all. Contact your dealer immediately if any thing is missing.
3 English Projector Overview Projector Outlook Front / upper side (S5201M/T111B/PS-X11M) (P5403/N243/PN-SX12) 5 1 5 1 6 7 2 3 7 2 3 8 4 8 4 # Description # Description 1 Power key and Power indicator LED 5 Control panel 2 Projection lens 6 Zoom ring 3 Elevator button 7 Focus ring 4 Lens cap 8 Remote control receiver Rear side (P5403/N243/PN-SX12) (S5201M/T111B/PS-X11M) 1 23 4 56 7 8 9 10 1 3 6 2 7 4 8 9 16 10 DC OUT 12 13 11 14 15 12 # Description 1 Remote
English 4 Control Panel 1 2 3 7 8 4 9 5 10 6 4 # Function Description 1 LAMP 2 POWER Power indicator LED 3 Power key Refer to the "Turning the Projector On/ Off" section. 4 Keystone Adjusts image distortion caused by tilting projection (±40 degrees). 5 MENU • Launches the Onscreen Display (OSD) menu, returns to the previous step for the OSD menu operation or exits the OSD menu. • Confirms your selection of items.
5 # Function English Remote Control Layout Description 1 Infrared transmitter Sends signals to the projector. 2 POWER Refer to the "Turning the Projector On/Off" section. 3 FREEZE To pause the screen image. 4 RESYNC Automatically synchronizes the projector to the input source. 5 BACK 6 Goes back to the previous selection.
English 6 # 11 Function Rewind Play/Pause Stop Fast-forward Description Rewinds/Plays/Pauses/Stops/Fast-forwards the playing media files. 12 VGA To change source to VGA. This connector supports analog RGB, YPbPr (480p/576p/720p/1080i/1080p), and YCbCr (480i/576i). 13 COMPONENT To change source to Component video. This connector supports YPbPr. 14 SD/USB A To change source to SD/USB A. This projector supports various formats for photo/audio/video files.
7 English Getting Started Connecting the Projector P5403/N243/PN-SX12 • VGA RS232 11 5 DVD player, Set-top box, HDTV receiver USB Display S-Video/ Video Output D-Sub 10 Y R B G 2 8 RS232 R B G D-Sub 7 1 W R 6 3 5 2 Speakers USB D-Sub HDTV adapter D-Sub R 10 9 W Y # Description # 7 4 Description 1 Power cord RS232 cable 2 VGA cable 8 HDMI cable 3 VGA to component video/HDTV adapter 9 3 RCA component cable 4 Composite video cable 10 RJ45 cable 5 Audio c
S5201M/T111B/PS-X11M • VGA 11 5 DVD player, Set-top box, HDTV receiver USB Display RS232 S-Video/ Video Output D-Sub 10 Y R B G 2 8 9 Speakers R B G 10 W R D-Sub RS232 7 6 3 5 2 1 D-Sub Microphone HDTV adapter D-Sub USB English 8 MIC.
9 English Turning the Projector On/Off Turning On the Projector 1 Remove the lens cap. 2 Ensure that the power cord and signal cable are securely connected. The Power LED will light red. 3 Turn on the projector by pressing (POWER) on the control panel or remote control, and the Power indicator LED will turn blue. 4 Turn on your source (computer, notebook, video player, etc.). The projector will detect your source automatically.
English 10 Turning Off the Projector 1 To turn the projector off, press the power button. This message appears: "Please press the power button again to complete the shutdown process." Press the power button again. 2 The LED power indicator will turn RED and blink rapidly after the projector is turned off, and the fan(s) will continue to operate for about 2 minutes to ensure that the system cools properly.
11 Adjusting the Height of the Projected Image The projector is equipped with an elevator foot for adjusting the image height. To raise the image: 1 Press the elevator button. 2 Raise the image to the desired height angle, then release the button to lock the elevator foot into position. 3 Use Tilt adjusting wheel to fine-tune the display angle. To lower the image: 1 Press the elevator button.
English 12 How to Optimize Image Size and Distance Consult the table below to find the optimal image sizes achievable when the projector is positioned at a desired distance from the screen. P5403/N243/PN-SX12 If the projector is 3 m from the screen, good image quality is possible for image sizes between 75" and 98". • Note: Remind as below figure, the space of 165 cm height is required when the projector is located at 3 m distance.
13 Note: Remind as below figure, the space of 480 cm height is required when located at 3 m distance. 242" B Height: 480 cm From base to top of image 3m Desired distance A Minimum Screen Size (Min zoom) Desired From base to Distance Diagonal top of image (m) (inch) W (cm) x H (cm) (cm) 0.5 40 82 x 61 80 1 81 164 x 123 160 1.5 121 246 x 184 240 2 161 328 x 246 320 2.5 202 410 x 307 400 3 242 492 x 369 480 3.5 282 574 x 430 559 4 323 656 x 492 639 4.
English 14 How to Get a Preferred Image Size by Adjusting Distance and Zoom The table below shows how to achieve a desired image size by adjusting either the position or the zoom ring. P5403/N243/PN-SX12 To obtain an image size of 50" set the projector at a distance between 1.5 m and 2.0 m from the screen and adjust the zoom level accordingly. • A D 50" Desired image size 1.5 m 2.
15 A 50" Desired image size D Height: 99 cm From base to top of image B& C 0.6 m Desired distance Desired Image Size Diagonal (inch) Distance (m) Top (cm) W (cm) x H (cm) Max zoom Min zoom From base to top of image < D > 30 61 x 46 0.4 0.4 59 40 81 x 61 0.5 0.5 79 50 102 x 76 0.6 0.6 99 60 122 x 91 0.7 0.7 119 70 142 x 107 0.9 0.9 139 80 163 x 122 1.0 1.0 158 90 183 x 137 1.1 1.1 178 100 203 x 152 1.2 1.2 198 120 244 x 183 1.5 1.
English 16 User Controls Installation Menu The installation menu provides an onscreen display (OSD) for projector installation and maintenance. Use the OSD only when the message "No signal input" is displayed on the screen. 1 Turn on the projector by pressing remote control. 2 Press "MENU" on the control panel or remote control to launch the OSD for projector installation and maintenance.
17 Empowering Key Acer Empowering Key provides three Acer unique functions: "Acer eView Management", "Acer eTimer Management", "Acer eOpening Management" and "Acer ePower Management". Press " " for more than one second to launch the Onscreen Display main menu to modify its function. Acer eView Management Press " " to launch "Acer eView Management". "Acer eView Management" is for display mode selection. Please refer to the "Onscreen Display (OSD) Menus" section for more details.
English 18 Onscreen Display (OSD) Menus The projector has multilingual Onscreen Display (OSD) menus that allow you to make image adjustments and change a variety of settings. Using the OSD menus • To open the OSD menu, press "MENU" on the control panel or remote control. • When the OSD is displayed, use to select an item in the main menu. After selecting the desired main menu item, press for feature setting. • Use to enter a submenu to select the desired item and adjust the settings by using .
19 English Color There are many factory presets optimized for various types of images. • Bright: For brightness optimization. • Presentation: For meeting presentation with higher brightness. • Standard: For common environment. • Video: For playing video in a bright environment. • Education: For education environment. • User: Memorize user’s settings. Display Mode Wall Color Use this function to choose a proper color according to the wall.
English 20 Color R Adjusts the red color. Color G Adjusts the green color. Color B Adjusts the blue color. Adjusts a video image from black and white to fully saturated colors. Saturation • Press image. to decrease the amount of color in the • Press image. to increase the amount of color in the Adjusts the color balance of red and green. Tint • Press image. to increase the amount of green in the • Press to increase the amount of red in the image.
21 Projection English Image • Front-Desktop: The factory default setting. • Front-Ceiling: When you select this function, the projector inverts the image for ceiling-mounted projection. • Rear-Desktop: When you select this function, the projector reverses the image so that you can project behind a translucent screen. • Rear-Ceiling: When you select this function, the projector reverses and inverts the image at same time.
English 22 H. Position (Horizontal Position) V. Position (Vertical Position) • Press to move the image left. • Press to move the image right. • Press to move the image down. • Press to move the image up. Frequency Changes the projector’s refresh rate to match the frequency of your computer’s graphics card. If you experience a vertical flickering bar in the projected image, use this function to correct it. Tracking Synchronizes the signal timing of the display with the graphics card.
23 Note: "Sharpness" function is not supported under computer mode. Note: The 3D function is supported by VGA source only. Please see the timing table for detailed 3D timings. It needs correct settings on graphics card 3D application program for correct 3D display. The SW players, such as Stereoscopic Player and DDD TriDef Media Player can support 3D format files. You can download these players on web page below. -NVIDIA Stereoscopic 3D Video Player: http://www.nvidia.com/object/ 3D_Drivers_Downloads.
24 English Use this function to customize the startup screen. To capture the image that you want to use as the startup screen, follow the instructions below. Notice: Before proceeding with the following steps, make sure that the "Keystone" is set to the default value "0", and the "Aspect Ratio" is set to "4:3". For details, refer to the "Image" section. Screen Capture • Change the "Startup Screen" from the default setting "Acer" to "User". • Press "Screen Capture" to customize the startup screen.
25 Press Security to change the "Security" setting. If the security function is enabled, your must enter "Administrator Password" first before changing the security setting. The factory default of "Administrator Password" is "1234". • Select "On" to enable the security function. You have to enter password depending on the "Security Mode". Please refer to "User Password" section for details. • If "Off" is selected, you can switch on the projector without password. Timeout (Min.
26 English Administrator Password You can enter "Administrator Password" when the "Enter Administrator Password" or "Enter Password" dialogue box is displayed. • Press to change "Administrator Password". The factory default of "Administrator Password" is "1234". If you forget your administrator password, do the following to retrieve the administrator password: • • Enter the unique 6-digit "Universal Password" which is printed on the Security Card that came with your projector.
27 To use the Interactive Pen, select "Enable" to activate this function. Link Channel • • Set a channel to differentiate between projectors and Interactive Pen communicate with the Interactive Pen. Setting Moving Key (for S5201M/ To use the moving key, select "Enable" to activate this T111B/PS-X11M) • function. When it is activated, you can only move the pointer by long-pressing the wheel button.
28 English To connect your projector to the network: 1 Take a RJ45 cable and connect one end to the LAN input jack of the projector and the other end to the RJ45 port. 2 Enter the LAN Setting menu. The "Enter Administrator Password" dialogue box is displayed. 3 Enter "Administrator Password". The next level menu is displayed. The factory default of "Administrator Password" is "1234". You can change it in the Setting > Security > Administrator Password menu.
29 Identify IP and Mask address. LAN Reset • (for S5201M/ T111B/PS-X11M) Reset LAN function. English LAN IP/Mask • (for S5201M/ T111B/PS-X11M) About LAN Setting (for P5403/N243/PN-SX12) Note 1 : An overview of the remote network operation page See Note 2 and Note 3. To switch input signals, click your desired signal. These buttons function the same as those on the OSD menus, projector control panel, or remote control. Note 2 : An overview of the Tools page You can enter the projector information.
English 30 Note 3: The Info page shows the projector information and status. About Interactive Pen Setting Note 1: Preparations 1. Connect the projector and your computer with a USB cable and VGA cable. 2. Turn on your projector and make suer it is displaying the computer’s image. 3. Enable the pen by selecting "Enable" in the Setting > Interactive Pen Setting > Pen Function menu. The pen’s link light starts to blink. 4. Point the pen at the screen to point, click, and drag.
31 1. Avoid standing too far from the screen. The closer you are to the screen, the better performance the pen has. 2. Hold the pen the way you hold a remote control or a pen. 3. A full battery charge takes 6-8 hours and will allow 20-40 hours non-stop use. The battery is only rechargeable, and is not user serviceable or user replaceable. 4. Avoid shadows! The pen cannot work if its tip is in a shadow or it is pointing at a shadow.
English 32 Audio (S5201M/T111B/PS-X11M) Volume • Press to decrease the projector speaker volume. • Press to increase the projector speaker volume. Press to decrease the microphone volume. Press to increase the microphone volume. Microphone • Volume (for S5201M/T111B/ • PS-X11M) Mute Power On/Off Volume • Choose "On" to turn mute on. • • Choose "Off" to turn mute off.
33 English Timer Timer Location Sets the location of the timer on the screen. Timer Start (or Stop) Press Timer Period (Minutes) Press Timer Volume Select this function to adjust the notification volume when the timer function is enabled and time is up. Timer Display Press to start or stop the timer. to adjust the timer period. to choose a timer display mode. Language Language Sets a language for the OSD menus. Use select your preferred language. • Press to confirm the selection.
English 34 Appendices Troubleshooting If you experience a problem with your Acer projector, refer to the following troubleshooting guide. If the problem persists, please contact your local reseller or service center. Image Problems and Solutions # 1 2 Problem No image appears onscreen Partial, scrolling or incorrectly displayed image (For PC (Windows 95/98/2000/XP)) Solution • Make sure all the cables are correctly connected as described in the "Getting Started" section.
35 4 5 6 7 8 Partial, scrolling or incorrectly displayed image (For notebooks) The screen of the notebook computer is not displaying your presentation Image is unstable or flickering Image has vertical flickering bar Image is out of focus Image is stretched when displaying a "widescreen" DVD title • Press "RESYNC" on the control panel or remote control. • For an incorrectly displayed image: • Follow the steps for item 2 (above) to adjust the resolution of your computer.
English 36 9 10 11 Image is too small or too large Image has slanted sides Image is reversed • • Adjust the zoom lever on the top of the projector. • Press "MENU" on the control panel or remote control. Go to "Image > Aspect Ratio" and try different settings. • If possible, reposition the projector so that it is centered on the screen and below the bottom of the screen. • Press the Keystone correction keys on the control panel or remote control until the image becomes square.
37 # 1 Condition Message Message Reminder Fan Fail - the system fan is not working. Fan Fail. Lamp will automatically turn off soon. Projector Overheated - the projector has exceeded its recommended operating temperature and must be allowed to cool down before it is used. Please also check the dust filters if they are installed. If the dust filter is clogged with dust, please clean it. Projector Overheated. Lamp will automatically turn off soon.
English 38 LED & Alarm Definition Listing LED Messages Message Power LED Lamp LED Temp LED Red Blue Red Red Standby (Power cord plugged in) V -- -- -- Power on -- V -- -- Lamp retry -- Quick flashing -- -- Turning off (Cooling state) Quick flashing -- -- -- Turning off (Cooling completed) V -- -- -- Error (Thermal failure) -- V -- V Error (Fan lock failure) -- V -- Quick flashing Error (Lamp breakdown) -- V V -- Error (Color wheel failure) -- V Quick flas
39 Use a screwdriver to remove the screw(s) from the cover, and then pull out the lamp. The projector will detect the lamp life itself. It will show you a warning message "Lamp is approaching the end of its useful life in full power operation. Replacement Suggested!" When you see this message, change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp.
Ceiling Mount Installation If you wish to install the projector using a ceiling mount, please refer to the steps below: Drill four holes into a solid, structurally sound part of the ceiling, and secure the mount base. m m m 13 m 20 1 .9 49mm 130 mm mm 8.4 English 40 Note: Screws are not included. Please obtain the appropriate screws for your type of ceiling. 2 Secure the ceiling rod using the appropriate type of cylinder screws.
41 Use the appropriate number of screws for the projector size to attach the projector to the ceiling mount bracket. Screw Type B Screw Type C Sliding Extension Large Washer Projector Bracket Supports projector and allows for adjustments Smaller Washer Spacer - For heat dissipation Note: It is recommended that you keep a reasonable space between the bracket and the projector to allow for proper heat distribution. Use two washers for extra support, if deemed necessary.
5 Adjust the angle and positioning as necessary. Tightening Screw Allen Key 30 Allen Key Tightening Screw Note: The appropriate type of screw and washer for each model is listed in the table below. 3 mm diameter screws are enclosed in the screw pack. Models Screw Type B P5403/N243/PN-SX12/ S5201M/T111B/PS-X11M Washer Type Diameter (mm) Length (mm) Large Small 3 25 V V 149.5 mm English 42 Screw M3 Depth 9.5 mm 242.
43 The specifications below are subject to change without notice. For final specs, please refer to Acer's marketing documentation.
English 44 Dimensions (W x D x H) • P5403/N243/PN-SX12: 290 x 255 x 125 mm (11.4" x 10.0" x 4.9") • S5201M/T111B/PS-X11M: 290 x 254 x 98.5 mm (11.4" x 10.0" x 3.9") Power supply Universal AC input 100 - 240 V, input frequency 50/60 Hz Power consumption • • Operating temperature 0ºC to 35ºC / 32ºF to 95ºF I/O connectors • Power socket x 1 • RS232 x 1 • VGA input x 2 • Composite video x 1 • S-Video x 1 • 3.
45 1 English Compatibility Modes VGA Analog - PC Signal Mode Resolution V.Frequency [Hz] VGA_60 640 x 480 59.940 31.469 VGA_72 72.809 37.861 VGA_75 75.000 37.500 VGA_85 85.008 43.269 VGA_70 720 x 400 H.Frequency [KHz] 70.087 31.469 85.039 37.927 56.250 35.156 SVGA_60 60.317 37.879 SVGA_72 72.188 48.077 SVGA_75 75.000 46.875 SVGA_85 85.061 53.674 VGA_85 SVGA_56 XGA_60 800 x 600 60.004 48.363 XGA_70 1024 x 768 70.069 56.476 XGA_75 75.029 60.023 XGA_85 84.
English 46 MAC19 1024 x 768@75Hz 75.020 60.241 MAC21 WXGA_60 1152 x 870@75Hz 75.061 68.681 1280 x 768 59.870 47.776 WXGA_75 74.893 60.289 WXGA_85 84.837 68.633 1280 x 720 60.000 45.000 WXGA_60 2 WXGA_60 1280 x 800 59.810 49.702 WXGA+_60 1440 x 900 59.887 55.935 1680 x 1050_60 1680 x 1050 59.954 65.290 1920 x 1080_RB 1920 x1080 60.000 66.587 1920 x 1080_EIA 1920 x1080 60.000 67.500 acer_16:9 1366 x 768 59.790 47.712 acer_timing 1024 x 600 60.000 37.500 61.
47 1152 x 864 SXGA_60 1280 x 1024 84.990 77.094 60.020 63.981 SXGA_72 72.000 76.970 SXGA_75 75.025 79.976 SXGA_85 85.024 91.146 1280 x 960 60.000 60.000 75.000 75.000 1400 x 1050 59.978 65.317 QuadVGA_60 QuadVGA_75 SXGA+_60 UXGA_60 1600 x 1200 60.000 75.000 Mac G4 640 x 480@60Hz 59.940 31.469 MAC13 640 x 480@67Hz 66.667 35.000 Mac G4 800 x 600@60Hz 60.317 37.879 MAC16 832 x 624@75Hz 74.546 49.722 Mac G4 1024 x 768@60Hz 60.004 48.363 MAC19 1024 x 768@75Hz 75.
English 48 3 4 1080p 60 67.5 1080P 1080p 50 24 56.26 27.00 1080p 23.98 26.97 Component Signal Mode Resolution V.Frequency [Hz] H.Frequency [KHz] 480i 720 x 480 59.94 15.73 480p 720 x 480 59.94 31.47 576i 720 x 576 50.00 15.63 576p 720 x 576 50.00 31.25 720p 1280 x 720 60.00 45.00 720p 1280 x 720 50.00 37.50 1080i 1920 x 1080 60.00 33.75 1080i 1920 x 1080 50.00 28.13 1080p 1920 x 1080 60.00 67.5 1080p 1920 x 1080 50.00 56.26 1080p 1920 x 1080 24.
FCC notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
English 50 Remarque à l'intention des utilisateurs canadiens Cet appareil numérique de la classe B est conforme a la norme NMB-003 du Canada. Declaration of Conformity for EU countries Acer hereby, declares that this projector series is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
This device must be used in strict accordance with the regulations and constraints in the country of use. For further information, please contact a local office in the country of use. Please see http://ec.europa.eu/enterprise/rtte/implem.htm for the latest country list.
English 52 Acer Incorporated 8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih Taipei Hsien 221, Taiwan Declaration of Conformity We, Acer Incorporated 8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih, Taipei Hsien 221, Taiwan Contact Person: Mr. Easy Lai, e-mail:easy_lai@acer.com.
The standards listed below are applied to the product if built with WLAN module or wireless keyboard and mouse. R&TTE Directive 1999/5/EC as attested by conformity with the following harmonized standard: • Article 3.1(a) Health and Safety -. EN60950-1 -. EN62311 • Article 3.1(b) EMC -. EN301 489-1 -. EN301 489-17 • Article 3.2 Spectrum Usages -. EN300 328 -. EN301 893 (Applicable to 5GHz high performance RLAN). Year to begin affixing CE marking 2010. Easy Lai /Manager Regulation Center, Acer Inc.
English 54 Acer America Corporation 333 West San Carlos St., San Jose CA 95110, U. S. A. Tel: 254-298-4000 Fax: 254-298-4147 www.acer.com Federal Communications Commission Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
