H.
Thank you for purchase our product. Please read this user manual carefully to ensure that you can use the device correctly and safely. Attentions: ◆The DVR should be installed in a well-ventilated place，keep suitable space from ground ,benefit for machine cooling，Be sure not to block its air vent.，keep away from heat sources and high temperaturea environment。 ◆Please keep the level installation of this product.
CONTENT 1. Product Introduction..................................................................................................... 4 1.1 Summary.................................................................................................................. 4 1.2 Main functions………………………………………………………………… 4 1.3 Front panel buttons description...........................................................................5 1.4 Rear panel diagram…………………………………………………………. . 6 1.
1. Product Introduction 1.1 Summary This device is a digital monitoring and recording product specially designed for the security field. It adopts standalone processor and standalone Linux operating system. The device combines with the latest technologies in the IT field, such as video and audio compression/decompression, large capacity HDD record, TCP/IP network etc.. The code is embedded in the FLASH chip, which makes the system running more steadily.
DVR accessories generally include: mouse, power lines and data lines. 1.3 Front panel buttons description Statement: the front panel interface, button layout and type, real product shall prevail. The front panel buttons Description: Buttons on Front Panel 1） IR Sensor（Red Color）: IR receiver for the remote control. 2） LED Indicators: Shows status of alarm, rec, power,link,HDD .
1.4 Rear panel diagram Statement: the rear panel interface, button layout and type, real product shall prevail.，below rear panel picture may be different with the actual panel.
1.5 Remote control In device operation, the enter key on remote control has the same function as left click of the mouse. The remote control is the secondary input device For navigating the system’s interface. To use the remote control: 1.STANDBY: When DVR on, constantly press the RED button on the top for 3 seconds, the DVR will be in standby status.Under standby mode, press one time for immediate start. 2.
2. Basic function operation 2.1 On/off Switching navigation 2.1.1 Start Before start，Please ensure all parts connected well！ Power on Equipment start，POWER indicator light is red. 2.1.2 Power off User can power off the device by using remote controller、keyboard and mouse. 2.1.3 By remote controller: Press Power button, the Shut down window will appear, click OK, the unit will power off after a while. 2.1.
Icon Sign description Recording Manual record Motion detection Alarm state Timing recording state Live playback Click Playbutton to playback the record enter fast record playback: as lelow picture: User can do concrete operation by click the buttons on screen. 2.
Pic2-3 Channel choose user could choose 1 channels from 1-4 to show live video.click Click function menu to save. ，will show dialogue frame as Pic 2-4; Pic 2-4 Mian function Click“Config”，display syswindows as pic2-5: Pic 2-5 Configuration management” Press MENU button on the front panel or the same button on remote control, also cuold display the same window.
2.4 Configuration management Configuration Management contains nine sub-menu: basic configuration, on-site configuration, video configuration, recording plan, alarm configuration, network configuration, user management, PTZ configuration and advanced configuration. 2.4.
2 ) Time & date Pic 2-7 Time & date Set the date format, time format time zone at the date and time "interface; Note: Click the "Default" button, the system restore the default settings; Click the "Apply" button will save the above settings; Click the "Exit"button to exit the current interface. 2.4.2 Live configuration Click“Live configuration” ，enter window as pic2-8 Live configuration includes two submenus : live and mask 2.4.2.
Tick off camera name and click “Setup” button to display a window as below： Pic 2-9 Live-color adjustment In this interface, user can adjust brightness, hue, saturation and contrast in live; click “Default” button to resort default setting, click “OK” button to save the setting.user can setup all channels with same parameters, please tick off “all” and then do relevant setup. 2.4.2.2 Mask Private mask.
2.4.3 Record configuration Click“Record configuration”，enter window as pic2-11： Record configuration includes four sub menus: start, record bit rate, Character overlay. recycle record. 2.4.3.1 Start Pic 2-11 Start Tick off record channel, channel audio. User can setup all channels with same parameters, tick off “All”, then to do relevant setup. Click “Default” button to resort default setting; click “Apply” button to save the setting; click “Exit” button to exit current interface.
2.4.3.2 Record bit rate Pic 2-12 Record bit rate Setup rate, resolution, quality, encode and max bit stream User can setup all channels with same parameters, tick off “All”, then to do relevant setup. Click “Default” button to resort default setting; click “Apply” button to save the setting; click “Exit” button to exit current interface. 2.4.3.
Stamp：User can overlap the channel name and time stamp on video . Pic 2-13 Character overlay Tick off camera name, time stamp; click Setting button, and then user can use cursor to drag the camera name and time stamp in random positions. Please refer to below Figures User can also setup all channels with same parameters. Click “Default” button to resort default setting; click “Apply” button to save the setting; click “Exit” button to exit current interface 2.4.3.
Click “Default” button to resort default setting; click “Apply” button to save the setting; click “Exit” button to exit current interface. 2.4.4.2 Motion Pic 2-15 Motion The setup steps of motion are familiar with schedule Note: the default schedule of motion detection is full-selected, that is, the color of schedule setting interface is blue. 2.4.4.
2.4.5.1 Sensor No sensor function. 2.4.5.2 Motion Motion includes one sub menus: motion 1> Motion Pic 2-21 Motion Click start motion alarm and set alarm hold time，It refers to after close motion alarm it delay to the preset setting time. Click alarm "Settings" button, show below window： Pic 2-22 Alarm handling Alarm configuration, trigger video alarm handling, linkage alarm handling and sensor alarm handling trigger settings is same.
of time (day or night), the users should adjust according to actual situation.click set All locales for the detection region；click icon， icon，will clear setting detection region； click icon，save setting；click button,exit from current interface. User can setup all channels with same parameters, please tick off “All”, and then to do relevant setup. Click “Default” button to resort default setting; Click “Apply” button to save the setting; click “Exit” button to exit current interface. 2.4.5.
2.4.6.1 Network Pic 2-27 Network configuration HTTP port：the default value is 80. If the value changed, user needs to add the port number when typing IP address in IE address blank. IE set HTTP port to 82, IP address: http://192.168.0.25 , user needs to input that address: http://192.168.0.25:82 into IE browser. Server port: data and image communication port NO. After selecting the "Obtain an IP address automatically", the device will distribute IP address, subnet mask, and gateway IP and DNS server.
2.4.6.3 Email Pic 2-29 Email SMTP Server/Port: the name and port number of SMTP server. Send address/password: sender’s email address/password. Receive address: receiver’s email address. Here user can add at least three mail addresses. Click Test button to test the validity of the mailbox. Click “Default” button to resort default setting；click “Apply” button to save the setting; click “Exit” button to exit current interface. 2.4.6.
2.4.7 User management Enter User management , as below pic： Pic 2-31 User management Clicking Add button, a dialog box will pop-up as below： Pic 2-32 General General: Input user name, password; select user type, input the MAC address of the PC; click OK button, this user will be added into the user list box; click Exit button to exit the current interface. 2 Authority: 1 Pic 2-33 Authority: In the authority interface, assign the definite operation right for that user.
2.4.8 P.T.Z configuration P.T.Z configuration includes two submenus: serial port and advance 2.4.8.1 serial port Pic 2-34 Serial port Click“Start” ，base on P.T.Z support Protocol to set Address, Baud rate,and Protocol. User can setup all channels with same serial port parameters, please tick off “All”, and then to do relevant setup. click “Default” button to resort default setting; click “Apply” button to save the setting; click “Exit” button to exit current interface.
In the Advance interface, after clicking preset “Setting” button, a dialog box will pop-up as below： Pic 2-36 Preset point setting In the preset set interface, click Setting button to see a window as below： Pic 2-37 Preset setting User can control the P.T.Z up, up left, down, right down, left , left down, right and up right and stop rotating；can adjust the rotation speed of the PTZ, focus and aperture；choose preset arrange NO.
Click Add button to add cruise line（max 32 cruise line can be added） ；select a cruise line and click Setup button, to see a window as below： Pic 2-39 Click Add Cruise set - preset pointsetting icon，to set the speed and time of preset point; select a preset point and click Delete icon to delete that preset poin；click Modify icon ，to modify the setting of a preset point；User can click those icons to adjust the position of preset point.
2.4.9 Advance configuration Advanced settings include three sub-menu: factory settings, andimport / export and exit. 1. Factory settings: all settings back to factory settings. 2. Import / Export: Users can export data files to be backed up onremovable storage devices, you can also import the specified data file from a removable storage device to a DVR. 3. Exit: exit current interface. Pic 2-41 Advance configuration Returned to the main menu, enter the data retrieval interface. 2.
Step 2：Select the channel, the calendar date , the start time and end time Step 3：click“Play” button, Playback will start from the set time bucket; click the corresponding button on the screen to start concrete operations. Pic 2-43 Playback buttons 2.5.2 Event search Step1:：enter into Search configurationevent search; refer to below pic.
2.6 Backup This unit supports backup by USB device，User also can make backup by IE browser via internet. Step1: enter into backup configuration interface, as below pic： Pic 2-45 Data backup Step2: set the start & end time, select channels and click Search button to display the searched data in the data backup list box.
2.8 Disk management Enter menu Disk management，In the interface, the user can view disk storage state, also can choose to formatting the hard disk Please format the hard disk before record ,Specific operation as below：. Step1: enter into disk management interface， The system will pop up the Disk Management window. Step2: select a hard disk and click Format button to star format.；set the property of the disk then click “Apply” button to save the setting.
2.9 Upgrade Once have the new version, the user can choose to upgrade the panel and the mianboard, can get upgraded software from the buyers, to upgrade the system. Upgrade step：user needs to copy the upgrade software which get from vendor into the USB storage device and then connect to the USB port. Enter Menu Upgrade，refresh list， the upgrade software name is displayed in the upgrade list box, select that software and click Upgrade button to start upgrading.
