DVR User Manual The guide is tailored for H.264-100 FPS /120 FPS 4-channel digital video recorder. All rights reserved.
Digital Video Recorder User Manual CONTENTS CHAPTER 1 Introduction ........................................................................................................................................................1 1.1 DVR Introduction ................................................................................................................................................................1 1.2 Main Features and Specification........................................................................
Digital Video Recorder User Manual 4.1.2 Accessing DVR in WAN ...................................................................................................................................................................................43 4.2 Main Interface ...................................................................................................................................................................45 4.2.1 Login ......................................................................
Digital Video Recorder User Manual CHAPTER 1 Introduction 1.1 DVR Introduction This DVR adopts the unique solution of Dual Stream technology, with a main processor that can process the signal of DVR recording and signal of internet transmission simultaneously, utilizing standard H.264 algorithm, the latest advanced video compression format.
Digital Video Recorder User Manual • Support to backup remotely by network client RECORD & PLAYBACK • Record modes: Manual operation, Sensor detection, Schedule Record and Motion detection • Support HDD recycle • Support single channel playback • Support deleting and locking the record • Support remote playback in Network Client through LAN or internet • Two record search mode: time search and event search ALARM 4 alarm inputs and 1 alarm output.
Digital Video Recorder User Manual CHAPTER 2 Panel Function Please make sure DVR is powered off before you connect the DVR with other equipment. Do not hot plug in! 2.1 Check the Accessories When you receive the machine, please check accessories and make sure you have all the parts. Normally, accessories include: a mouse, a power cable, a CD-ROM with ‘Network Client’ software and some screws for installing HDD. You could use screwdriver and some screws to fix the HDD into DVR.
Digital Video Recorder User Manual 1 3 5 7 9 11 13 HDD tray 2 Number buttons Menu /Number Add button 4 PTZ /Del /Number Decrease button Manual record /Focus button 6 Search /Zoom button Play/Iris button 8 Fast backward /Speed button Fast forward /Input Mode button 10 Stop /ESC button Indicator lights 12 Enter button Left /Up /Right /Down buttons 14 USB interface Fig2.1 Front Panel "A" button is used to switch the inputting mode. LED has six indicator lights.
Digital Video Recorder User Manual contrast below figure and the entity for realizing the function of every interface. The Back Panel and interface terminal is shown as Fig2.2 Back Panel. 1 3 5 7 9 Power plug 2 Alarm in/alarm out RS485 4 LAN port Audio in 1-2 6 S-video output Audio output 8 Video output Video in 1-4 Fig2.2 Back Panel 2.4 Remote Controller Introduction 2.4.1 Use Remote Controller Notice: Please note that Remote Controller is not a standard part of this DVR.
Digital Video Recorder User Manual − Whether there are some signals which transmitted by other devices disturbing the Remote Controller or not. Notice: If the possibilities above are excluded, please contact with vendor to change the Remote Controller. 2.4.2 Facie of Remote Controller The entire facie of the Remote Controller is shown in Fig2.3 Remote Controller. Fig2.3 Remote Controller All buttons on the Remote Controller describes as below table.
Digital Video Recorder User Manual Button Name 1-16 1X1 2X2 3X3 4X4 MENU SEARCH Upward Leftward Rightward Downward SR SF -SET+ Play Description Number Buttons These number buttons are used for selecting channels and other functions. Full-screen display mode Press the button to display the picture of single channel. Four-screen display mode Press the button to display the picture of four channels. Press "1X1" button in four-screen display mode to enter the channel 1.
Digital Video Recorder User Manual Button Name Fast backward Fast reverse button Press the button to backward play the record. There are three backward multiple to choose: 2X, 4X, 8X. Fast forward Fast forward button Press the button to forward play the record. There are three forward multiple to choose: 2X, 4X, 8X. Stop Stop button: Press the button to stop playing record. Audio switch Audio switch button Press the button to switch the audio of the channel.
Digital Video Recorder User Manual Button Name SPEED+/- Description SPEED- button Control the rotational speed of the Fast Speed Dome. The following table shows all letters which number buttons correspond. Number Button 1 3 5 7 9 Corresponding Letter ().
Digital Video Recorder User Manual CHAPTER 3 Basic Operation Guide 3.1 How to Start DVR Notice: Before you power on the machine, please make sure the power input of DVR is eligible for local power supply. If the power indicator light is off, please do as the following to start DVR: STEP1 Connect DVR to AC adaptor and plug in. STEP2 Turn on the DVR. STEP3 Wait for DVR to initialize. After the DVR is powered on, ‘STARTING……’ appears on the screen, which indicates DVR is initializing.
Digital Video Recorder User Manual (referred Fig3.2 Main Menu). MAIN MENU BASIC CONFIG LIVE CONFIG RECORD CONFIG ALARM CONFIG PTZ CONFIG USER CONFIG NETWORK MANAGER TOOLS Fig3.1 Login Fig3.2 Main Menu STEP2 Press "Up", "Down", "Right" and "Left" buttons to move cursor, selection highlighted by yellow. STEP3 Press "Enter" key to enter the sub-menu. And press "Menu" key to get back to Main Menu when you use the front panel to operate. The structure of the main menu is shown in Fig3.3.
Digital Video Recorder User Manual Fig3.3 Structure of Main Menu 3.2.1 Basic Configuration Basic Configuration menu is shown as Fig3.4 Basic Configuration. Fig3.4 Basic Configuration Fig3.5 Time Adjust 1. VIDEO FORMAT After you enter the Basic Configuration menu, you need to set the video format. There are two options to choose: NTSC and PAL. STEP1 Press "Up", "Down", "Left" and "Right" buttons to move the cursor manually. STEP2 Press "Enter" key to change the video format. 2.
Digital Video Recorder User Manual You could set DVR name. Range for inputting the words contents letters from ‘a’ to ‘z’ and numbers from ‘0’ to ‘9’. STEP1 Press "A" button to switch the inputting mode STEP2 Modify the DVR name. STEP3 Press "Enter" key to confirm the operation. 4. DVR ID You could set DVR ID. It consists of three numbers. STEP1 Press "Up", fDown", "Left" and "Right" buttons to move the cursor. STEP2 Press "Enter" key to modify numbers.
Digital Video Recorder User Manual Fig3.6 Live Configuration 1. CHANNEL STEP1 Press "Up", "Down", "Left" and "Right" buttons to move the cursor. STEP2 Press "Enter" key to switch the channel which you want to set. 2. CHANNEL NAME You could set the channel name. Range for inputting the words contents letters from ‘a’ to ‘z’ and numbers from ‘0’ to ‘9’. STEP1 Press "A" button to switch the inputting mode. STEP2 Input channel name. STEP3 Press "Enter" key to confirm the operation. 3.
Digital Video Recorder User Manual Modify value of contrast, brightness, saturation and hue of the picture. 6. COPY CONFIG TO Copy the configurations of this channel to any other selected channel. STEP1 Select the channel which this channel will be copied to. STEP2 Press "COPY" button. STEP3 Press "Enter" key to confirm the operation. 3.2.3 Record Configuration Record Configuration menu is shown as Fig3.7 Record Configuration. You could enter the menu to set the parameters of record.
Digital Video Recorder User Manual 2. RECYCLE If select "RECYCLE" check box to have continuous recording, DVR will overwrite the oldest record when HDD is full. If you unselect "RECYCLE" check box, the DVR will stop recording when the HDD is full. 3. TIME STAMP If selecting the check box, record time will be displayed on the bottom of screen when playing back the record. 4. PRERECORD TIME Prerecord time is the record time before alarm. There are two options to choose: 5 seconds and 10 seconds. 5.
Digital Video Recorder User Manual On weekday and holiday, you can select record whole day or set four periods of time to record. 9. FRAME RATE SETUP Frame rate is the recording picture amount per second. If you choose 15, the picture recording rate is 15 frames per second. You could set frame rate for different record mode. If the video format is NTSC, there will be five frame rates to choose: 1, 3, 7, 15 and 30. The maximum of the frame rate is 30.
Digital Video Recorder User Manual 1. HOLD TIME It sets the record time after the alarm happened. There are two options to choose: 1 minute and 2 minutes. It also sets the distant time of detecting the motion. If the HOLD TIME is 1 minute, the motion which is detected will only trigger the alarm once in 1 minute. 2. CHANNEL STEP1 Press "Up", "Down", "Left" and "Right" buttons to move the cursor. STEP2 Press "Enter" key to switch the channel which you want to set. 3.
Digital Video Recorder User Manual − − NULL: No area will be detected. BACK: Go back to Motion Alarm Configuration menu. Fig3.11 Detection Area Setup STEP3 Substeps of manually selecting the detection area are described as below: 1. In the Area Setup submenu, press "Up" and "Down" buttons to choose "CUSTOM" option. 2. Press "Enter" key to confirm the operation. 3. Press "Up", "Down", "Left" and "Right" buttons to choose the part which needs to be detected. 4.
Digital Video Recorder User Manual Fig3.12 Sensor Alarm Configuration 1. HOLD TIME It sets the record time after the alarm happened. There are two options to choose: 1 minute and 2 minutes. It also sets the distant time of detecting the motion. If the HOLD TIME is 1 minute, the sensor event which is detected will only trigger the alarm once in 1 minute. 2. SENSOR STEP1 Press "Up", "Down", "Left" and "Right" buttons to move the cursor to "SENSOR" option. STEP2 Press "Enter" key to switch the Sensor. 3.
Digital Video Recorder User Manual ‘NC’ means normal close. If ‘NC’ is chosen, the DVR will alarm when the alarm is in high level. 5. TRIGGER RECORD One channel can connect to one sensor. But one sensor can match one or more channels. STEP1 Press "Up", "Down", "Left" and "Right" buttons to move the cursor to "TRIGGER RECORD" option. STEP2 Select the check box of the channel which sensors match. STEP3 Press "Enter" key to confirm the operation.
Digital Video Recorder User Manual There are two options of alarm output: ALARMOUT1 and BUZZER. 3.2.5 PTZ Configuration PTZ Configuration menu is shown as Fig3.14 PTZ Configuration. Fig3.14 PTZ Configuration Fig3.15 Preset 1. CHANNEL Switch to the channel which connects to the Speed Dome. 2. BAUDRATE There are five options of baudrate to choose: 1200, 2400, 4800, 9600 and 19200. 3. PROTOCOL Choose the PTZ protocol.
Digital Video Recorder User Manual position of the Presetting Point. STEP5 Press "UP", "DOWN", "RIGHT" and "LEFT" buttons to rotate the Speed Dome. STEP6 Press "ESC" button to come back the Preset menu. STEP7 Press "SAVE" button to save the position of camera which you adjust before as Presetting Point; press "CANCEL" button to discard the setting to get back to upper menu. Notice: Do you know how to use the Presetting Point? You can use the number key to switch the Presetting Point in PTZ mode.
Digital Video Recorder User Manual 1. AUTHORIZATION CHECK If select "AUTHORIZATION CHECK" check box, all users need input the password before entering the Main Menu. If unselect "AUTHORIZATION CHECK" check box, users can enter the system directly without password. 2. USER Press "Enter" key to switch to another user. Using "+” and "-" buttons could also change the user. 3. PASSWORD Admin’s password is initialized as ‘123456’. Users with authorization change this user’s password.
Digital Video Recorder User Manual 3.2.7 Network Configuration Network Configuration menu is shown as Fig3.18 Network Configuration. You could enter the submenu to set the parameters of network. Fig3.18 Network Configuration Fig3.19 Basic Configuration BASIC CONFIGURATION Basic Configuration submenu is shown as below Fig3.19 Basic Configuration. STEP1 Press "Up", "Down", "Left" and "Right" buttons to move the cursor. STEP2 Press "Enter" key to enter the Basic Configuration menu. 1.
Digital Video Recorder User Manual Fig3.20 IP Configuration Fig3.21 System Information It is the IP configure of the DVR. There are three options to choose: STATIC, DHCP and PPPoE. Take Static IP address as example. STEP1 Press "Up", "Down", "Left" and "Right" buttons to move the cursor. STEP2 Input IP Address, Subnet Mask and Gateway. STEP3 Press "OK" button to modify the IP Configuration menu. If select DHCP, the IP address will be automatically assigned by local network.
Digital Video Recorder User Manual Use DDNS, user need to get a domain name from the ISP whose protocol is packed in DVR. Fig3.22 DDNS Configuration Notice: The actual ISP list may be different from each vendor. Take the ‘dns2p.com’ as example to introduce. If different from the below example, please connect with your Domain Name Service Provider to be guided how to get the domain. 1. Apply the Domain Name (1) Register in the Web STEP1 Fill in the blank of IE address with ‘www.dns2p.com’.
Digital Video Recorder User Manual Fig3.24 Login Page Fig3.23 Register Page (2) Login STEP1 Return to homepage after registering successfully. STEP2 Click "Account Manager" on the right of homepage to login (referred Fig3.24 Login Page). STEP3 Input the username and password with the information that you have registered. STEP4 Click "Enter" key after filling in the textbox. (3) Domain Setup STEP1 Click "Domain Management" on the left to set the domain (referred Fig3.25 Domain Setup). Fig3.
Digital Video Recorder User Manual (referred Fig3.26 Dialog Box). Fig3.26 Dialog Box Notice: Time of probationary period is one month. If user wants to use it continuatively after one month, please click "Buy Now" in the right of homepage to pay for it. 2. Setup in the DVR (1) DOMAIN Domain is set in ‘1 Apply the Domain Name’. According to the example above, the domain is ‘dvr.dns2p.com’. (2) USER ID Username of registered which is set in ‘(1) Register in the Web’.
Digital Video Recorder User Manual Fig3.27 Manager Tools Fig3.28 Disk Management SHUTDOWN SYSTEM You could shut down system through this function. STEP1 Press "Up", "Down", "Left" and "Right" buttons to move the cursor for entering the SHUTDOWN submenu. The following words will be shown: ‘ARE YOU SURE TO SHUT DOWN DVR SYSTEM?’. STEP2 Press "Enter" key to confirm the operation. DISK MANAGEMENT Disk Management submenu is shown as Fig3.28 Disk Management. There are two options to choose: FORMAT and CANCEL.
Digital Video Recorder User Manual HDD is formatted. • Before you format the HHD, you must stop recoding and playing back. • Time for formatting the HDD is subjected to the HDD capability. The bigger capability is, the time is longer. Normally, a 40G HDD takes about eighty seconds to format. SYSTEM LOG System log submenu is shown as Fig3.29 Log Search. You could inquire the operation log on DVR. The DVR will note the operation, status and time automatically when the DVR is working.
Digital Video Recorder User Manual STEP4 Press "OK" button to view the event log; Press "CANCEL" or "ESC" button to cancel this operation. The information of log files content start time, end time and log file types. For example: 110707:092151 means 2007-7-11 9:21:51 and N-L means the LOGIN of the NET. If there are too much log list, user can use "PREV" button to page up and use "NEXT" button to page down. SYSTEM INFORMATION System information submenu is shown as Fig3.30 System Information.
Digital Video Recorder User Manual Fig3.32 Updating STEP5 After the program checked is done, the system will restart. If DVR reboot normally, DVR is updated. LOAD DEFAULT Fig3.33 Load Default Load Default menu is shown as Fig3.33 Load Default. It loads the factory default setup. CLEAR ALARM OUT Clear the current alarm out, referred Fig3.34 Clear Alarm Out. Fig3.
Digital Video Recorder User Manual 3.3 Shortcut Menu 3.3.1 PTZ Fig3.35 PTZ Mode PTZ mode is shown as Fig3.35 PTZ Mode. In order to switch the channel to which connects the video output of the Speed Dome, you may press "PTZ" button to enter the PTZ mode. In the live view of PTZ mode, the default channel is channel 1, you can use mouse to change the channel number to enter the corresponding channel PTZ mode. SPEED STEP1 STEP2 STEP3 In PTZ mode, press "Speed" button.
Digital Video Recorder User Manual STEP2 FOCUS STEP1 STEP2 Press "+" and "-" buttons to zoom in and zoom out. In PTZ mode, press "FOCUS" button. Press "+" and "-" buttons to control focus. IRIS STEP1 STEP2 In PTZ mode, press "IRIS" button. Press "+" and "-" buttons to control little and much light of the Speed Dome. 3.3.2 Search Press the "Search" button, there are five submenus displayed on the screen: PLAYBACK, BACKUP, DELETE and LOCK. Data menu is shown as Fig3.36 Data. PLAYBACK 1.
Digital Video Recorder User Manual All the record can be searched through this function. Steps of search by time as below: STEP1 In Calendar submenu, press "Up", "Down", "Right" and "Left" buttons to select date. STEP2 Press "Enter" key to enter the Playback submenu, referred Fig3.38 Playback. STEP3 Press "Enter" key to select channels. STEP4 Press "Up", "Down", "Right" and "Left" buttons to select time of the date which you select ahead. The time in red has record file.
Digital Video Recorder User Manual STEP6 STEP7 STEP8 − CH: Channel. − START TIME: The start time of the record. − TYPE: The type of the event. There are two types of event: MOTION and SENSOR. − M: Motion detection. − A: Sensor detection. − LOCK: Lock status of files. Press "Up" and "Down" buttons to choose the event record. Press "Enter" key to play back the record which is chosen. Press "Stop" button to get back to live display mode.
Digital Video Recorder User Manual It selects the format of backup file. It supports AVI and DAT video format. When you select DVR, the video format of backup file will be DAT. (3) START TIME Start recording time to backup. The first line is hour, and the second line is minute. You must choose the date firstly and choose the time secondly. (4) END TIME End recording time to backup. The first line is hour, the second line is minute. You must choose the date firstly and choose the time secondly.
Digital Video Recorder User Manual Backup progress will be displayed on screen, as Fig3.41 Backup Progress. If you stop recording when you backup the record files, the backup speed will be faster. STEP4 When the backup is over, the system will pop up a dialog box. The sentence in the dialogue is as following: ‘BACKUP COMPLETELY’. So far, the backup is completed. 2. VIEW BACKUP If backup with AVI format, most media player can view directly. If backup with DVR format, please use the client software to view.
Digital Video Recorder User Manual displayed in yellow. STEP2 Press "Enter" key to enter the Delete submenu. STEP3 In the Delete submenu, use "UP" and "DOWN" buttons to move the cursor. STEP4 Press "Enter" key to select the record. STEP5 Move the cursor to "DELETE" button and press "Enter" key, information will be given as below: ‘SOME RECORDS WILL BE DELETED, CONTINUE?’ STEP6 Press "Left" and "Right" buttons to select "OK" button. STEP7 Press "Enter" key to delete this record.
Digital Video Recorder User Manual of HDD, record mode including manual/alarm/motion etc. 3.3.4 Other • In live display mode, if you press the "Up" button, it will display the first channel in full screen. • If you press the "Down" button, it will display the second channel in full screen. • If you press the "Left" button, it will display the third channel in full screen. • If you press the "Right" button, it will display the fourth channel in full screen.
Digital Video Recorder User Manual CHAPTER 4 Remote Surveillance 4.1 Accessing DVR Because our DVR supports IE control, you need use IE connect to DVR and download and install ActiveX controls for remote controlling the DVR. Before remote controlling the DVR, you need right connect the DVR and cable to internet. If you access the DVR through WAN, you need to set DVR and router parameters firstly. DVR could support five users logging in and operating the Network Client synchronously. 4.1.
Digital Video Recorder User Manual Figure4-1 Network Client Interface 4.1.2 Accessing DVR in WAN When you access DVR in WAN, you need to set safety certificate firstly. STEP1 Double-click the IE browser icon to open the IE browser. STEP2 Select ‘tools > Internet Options’ in menu bar, it will pop up "Internet Options" window, referred Figure4-2 Internet Optionss.
Digital Video Recorder User Manual Figure4-3 Security Settings Figure4-2 Internet Options STEP3 Click "Security" option, and click "Custom Level…" in "Security level for this zone", it will pop up "Security Settings" window, referred Figure4-3 Security Settings. STEP4 In "Security Settings" window, enable the options which relate with ActiveX controls. STEP5 Click "OK", finish setting the parameters. STEP6 Input IP of the DVR in IE textbox, then press "Enter" key.
Digital Video Recorder User Manual STEP8 The system access DVR automatically after finishing installation. The Network Client interface will be displayed in IE browser, referred Figure4-1 Network Client Interface. Notice: When the Network Client is running on VISTA operation system, you also need set relational ActiveX parameters. Steps of setting parameters are shown as follows: 1. Open IE browser, then select ‘Internet Options > Advanced > Security’. 2.
Digital Video Recorder User Manual 4.2.1 Login The operation of the Network Client is the same as the DVR. Default username is ‘Admin’ and password ‘123456’. STEP1 STEP2 Click button to input username and password in the pop-up box. Press "Enter" key to login. Notice: Click "EXIT" button, you could exit the system. 4.2.2 Snap Picture Snap live picture. Press to snap the picture. 4.2.3 Parameter Settings Parameter Settings window could set the amount how many picture you snap once.
Digital Video Recorder User Manual 4. Red indicator light: Sensor Alarm Record State. 5. Blue indicator light: Video Loss State. 4.3 Remote Playback and Search 4.3.1 Remote Playback Click button in the Main Interface to enter the following area which is shown as Fig4.3 Remote Playback. Fig4.3 Remote Playback Meaning of the function button in the Remote Playback window is shown as below: 1. : Play /Pause.
Digital Video Recorder User Manual 2. 3. 4. : Stop. : Next frame. This button will be valid when playback is paused. You can select suitable speed for playing record in the area as Fig4.4 Multiple of Playing. Fig4.4 Multiple of Playing Fig4.5 Data Preview Fig4.5 Data Preview shows the record data of different channels in corresponding time. In the figure, left side shows the available channels.
Digital Video Recorder User Manual 4.3.2 Other Functions BACKUP Click button to enter the Backup window which is shown as Fig4.6 Backup. Fig4.6 Backup There are two methods of backup: backup by time and backup by event. 1. TIME BACKUP STEP1 Select the time and record type. STEP2 Select the camera. STEP3 Press "Browse…" button to select the folder of saving the Backup file. STEP4 Select cameras which you want to backup. STEP5 Select the type of backup file.
Digital Video Recorder User Manual 2. EVENT BACKUP STEP1 Select the time and record type. STEP2 Select the camera. STEP3 Press "Browse…" button to select the folder of saving the Backup file. STEP4 Select cameras which you want to backup. STEP5 Select the type of backup file. STEP6 Click "Select Event" button to enter the Select Event window which is shown as Fig4.7 Select Event. Fig4.7 Select Event 1.
Digital Video Recorder User Manual STEP7 Click "OK" button to run the backup. LOCK /UNLOCK You could select the record which you want to lock/unlock. STEP1 Click button to enter the Remote Lock window, as Fig4.8 Remote Lock. Fig4.8 Remote Lock Fig4.9 Lock Event STEP2 Select the time and record type. STEP3 Select the camera. STEP4 Click "Select Event" button, system find the corresponding event and it will pop up the LOCK EVENT window which is shown as Fig4.9 Lock Event.
Digital Video Recorder User Manual 4.4 Remote DVR Configuration Click button in the Main Interface to enter the following interface which is shown as Fig4.10 Remote DVR Configuration. Fig4.10 Remote DVR Configuration The definitions of the buttons in Fig4.
Digital Video Recorder User Manual The Remote DVR Configuration can set the configurations of the DVR remotely. The operation is the same as DVR. It can change the configuration of DVR. 4.4.1 Basic Configuration Click button in the Remote DVR Configuration and enter the Basic Configuration which is shown as below Fig4.11 Basic Configuration. After you change parameters of the Basic Configuration window, click "OK" button, the setting will be saved and inured on the DVR. Fig4.11 Basic Configuration 1.
Digital Video Recorder User Manual 4. DVR No. When you have more than one DVR, you can give a number to every DVR. 5. Date Format Select the option in the drag-down list to change the format of date. There are three date format : YY/MM/DD、DD/MM/YY 和 MM/DD/YY. 6. Buzzer Select the option in the drag-down list to change the time how long the buzzer will last. 4.4.2 Live Configuration button in the Remote DVR Configuration, the drag-down menu will appear.
Digital Video Recorder User Manual 2. Channel Hide Select the check box to change be hidden or shown the picture of DVR channel in the live display mode. 3. Show Name Select the check box to change be hidden or shown the name of DVR channel in the live display mode. 4. Channel Name Input words to change the name of the channel. COLOR SETTINGS 1. Channel Select the option in the drag-down list to change the channel of DVR. 2.
Digital Video Recorder User Manual 1. Parameter Settings The setting is the same as ‘3.2.3 Record Configuration’ of the DVR. If you change it on Network Client, the DVR will change along with it. 2. Schedule Record The default value of Schedule Record is not active. STEP1 Click the check box of the Schedule Record, it will be active. The default schedule time is every day. STEP2 Click the "Set Schedule" button, the Schedule Configuration window will pop up as Fig4.15 Schedule Configuration. Fig4.
Digital Video Recorder User Manual 4.4.4 Alarm Configuration button in the Remote DVR Configuration, the drag-down menu will appear. There are Motion Alarm window, Click Sensor Alarm window and Other Alarm window. The setting is the same as ‘3.2.4 Alarm Configuration’ of the DVR. If you change it here, the DVR will change along with it. 4.4.5 Network Configuration Click button to change the video quality of the Network Client in the Network Configuration window. 4.4.
Digital Video Recorder User Manual Fig4.16 Software Update STEP3 After update finishing, DVR need to be rebooted to apply the new firmware. LOAD DEFAULT Load default setup. SYSTEM INFORMATION It displays the information of the DVR, such as version, DVR name and MAC address and so on. SYSTEM LOG It displays the information about operating information on the DVR. 4.5 Remote PTZ PARAMETERS Before operating the Remote PTZ, you should set the PTZ configuration. PTZ Configuration window is shown as Fig4.
Digital Video Recorder User Manual Fig4.17 PTZ Configuration 1. Channel When you need to set PTZ control, you should enter the PTZ configuration window and click the corresponding channel. Then users can begin to control the PTZ through enabled channel. 2. Baud Rate It sets the Baud Rate of PTZ device. The default value is 9600. 3. Protocol It sets the communication protocol of PTZ device. 4. Address It sets the communication address of PTZ device.
Digital Video Recorder User Manual PTZ CONTROL INTERFACE Fig4.18 PTZ Control Click button in the Main Interface (referred Fig4.2 Main Interface) and enter the PTZ Control interface which is shown as Fig4.18 PTZ Control. You can control PTZ devices by the function buttons on the right side of the interface. The function of the buttons is described as below table. Icon Description Rightward Controlling the Speed Dome to swing right. 60 Icon Description Leftward Controlling the speed dome to swing left.
Digital Video Recorder User Manual Icon Description Icon Description Upward Controlling the speed dome to swing up. Downward Controlling the speed dome to swing down. FOCUS+ It sets the camera’s long focus. ZOOM+ It sets the camera’s zoom in. IRIS+ It sets the PTZ device’s much light. FOCUSIt sets the camera’s short focus. ZOOMIt sets the camera’s zoom out. IRISIt sets the PTZ device’s little light.
Digital Video Recorder User Manual CHAPTER 5 Operation with Mouse 5.1 Switch the Display of Channel You can switch the display mode of channels in DVR with mouse. • If the picture of the channel is in multi-divided mode, you could switch the picture to full screen through clicking on the picture. • If the picture is in full screen mode, you could switch the picture to multi-divided mode through clicking on the picture. 5.
Digital Video Recorder User Manual Right-click on the picture to exit the menu. 5.2.3 PTZ Control Click "PTZ Control" menu to enter the PTZ mode. The shortcut menu of PTZ is shown as Fig5.1 Shortcut Menu of PTZ. You could control the zoom-in and zoom-out, focus and input lightness of the Speed Dome. Fig5.1 Shortcut Menu of PTZ FOCUS Click "FOCUS+" button to control long focus of the Speed Dome. Click "FOCUS-" button to control short focus of the Speed Dome.
Digital Video Recorder User Manual Notice: , , and buttons are used to control the Speed Dome to swing up, right, left and down. 5.3 Fast Reverse and Fast Forward When you play back the record, you can backward or forward the record. Multiple of reversing and forwarding is controlled through using the mouse. The shortcut menus of fast backward and fast forward are shown as Fig5.2 Fast Reverse and Fast Forward. Fig5.2 Fast Reverse and Fast Forward • • • • 64 Click button to play back the record.
Digital Video Recorder User Manual CHAPTER 6 Frequently Asked Questions Question1: You have been download and install Network Client software from the DVR. But after inputting DVR IP, username and password, it appears ‘ Can’t open codec TVTTH ’. Answer: When installing the software, the system regedit and system file need to be modified. And if you login the system as ordinary user, the modification operation could not be performed.
Digital Video Recorder User Manual Appendix A Main Standard & Parameter Model VIDEO Input Level Video Standard Video Output Screen Split Control Display Resolution Speed AUDIO Compression Audio In/ Out Input Level RECORDING Compression Compression bit rate Resolution NTSC PAL Speed NTSC PAL Mode Motion detection HDD interface SEARCHING Searching Method REMOTE SURVEILLANCE Monitoring Environment Real Time 66 4Channel NTSC PAL NTSC PAL 4×BNC 1.0Vp-p±10%.75Ohm NTSC / PAL 2×BNC 1.0Vp-p±10%.
Digital Video Recorder User Manual ALARM Sensor Input Alarm Output Motion Detection CONNECTOR Video Input Main Monitor Output Audio Input (Mono) Audio Output (Mono) Sensor Input Alarm Output PTZ (RS-485) Ethernet USB 1.
Digital Video Recorder User Manual Appendix B Record Capability The following table shows how much capability record of 4 channels engrosses per hour.
Digital Video Recorder User Manual Appendix C Abbreviation Words L M L-L PB O-D SYS DVR Meaning Lock Motion Detection The Login of Local Playback and Backup Disk full of System Logs The Event of System Setting or the System Reset Digital Video Recorder Words HDD A VLoss N-L L-C N-C DEL Meaning Hard Disk Sensor Detection Video Loss The Login in or Login out of the Network Change Configuration of the DVR from the DVR Change the Configuration of the DVR from Network Deletion Event 69