Specifications

32
Controls
Specifications
Dimensions 9.5"H x 5.6"D x 2.5"W
Weight 3.6 lb
Input Power 90 to 265Vac, 50/60 Hz
Current less than 0.4 ampere at 115Vac
Sink Mode Source Mode
Outputs
Load Power Supply built in 24v supply
or external 12 to 24v
Current rating 50ma 50ma
Voltage rating 24vdc
On state voltage 2.0 V max @ 50 ma 20 V min @ 50 ma
On state leakage 0.6 ma max @ 24 vdc 0.6 ma max
Inputs
On state voltage range 2.3 to 12 volts 10 to 24 vdc
Input current 2.3 ma @ 12 volts 2.3 ma @ 10 volts
6.5 ma @ 0 volts 6.5 ma @ 24 volts
Operating temperature +32°F to +122°F
Storage temperature -40°F to +167°
Humidity 95% Max. noncondensing
For BP93, BI12 Actuators
SS2000I Programmable
Motion Control
The SS2000 control consists of a
SS2000I indexer and SS2000D6
6 amp drive. The SS2000I indexer
includes the MS2000 programming
software and an RS232 cable. The
SS2000D6 includes a 10 foot motor
power cable. Both the indexer and
drive must be ordered to operate an
Electrak 2000 actuator.
Options
Plug In Closed Loop Module With
Memory Board
This module can be added to any
SS2000I control to convert it into a
Closed Loop unit. The module
replaces the memory board on a
standard open loop control. The
change can be done from the front
of the control without requiring
access on either side, allowing the
module to be added without
removing the SS2000I control. A 10
foot cable is included. Order part
number 221147-001. For factory
installed Closed Loop Module,
order control as SS2000I-V.
BCD Switch Option
Up to two BCD switches can be
connected to an SS2000I control
for entry of BCD data. BCD switch
data is scalable. Applications for
this function include moving to a set
position, selecting one of several
programs, or selecting move
distance and speed.
Kit 221157-001 provides just the
BCD switch assembly. A cable is
required to connect the switch to
the control. The cables are listed
separately below. If a second switch
is required, order part number
221157-002, which includes a
switch assembly and an 18-inch
long ribbon cable for daisy chaining
two switches.
Cable Length Part Number
5 feet C215851-007
10 feet C215851-008
Dual Mounting Bracket
For mounting SS2000I and
SS2000D6 together
221459-001
SS2000D6 Drive
Features
• Switch selectable step resolutions
(full step to 1/250 microstep)
• Optically isolated inputs
• Boost Current, Reduce Current
and Windings Off function
• Built in AC line filter plus MOV
• Self test function
• Latched short circuit protection
Features
• Single point, removable terminal
strips for all I/O
• All I/O are optically isolated, switch
selectable for sinking or sourcing
• Thirteen programmable inputs with
three dedicated high speed inputs
• Eight programmable outputs with
short circuit protection
• Can control two drives, one at a time
• Subroutines and loops nestable
to four levels
• MS2000 programming software for
use with DOS compatible computers
• Internal AC line filter and MOV provide
protection from noise on input power
• Optional plug in module for closed loop
operation (encoder required on actuator)
• UL recognized
• Unlatched undervoltage and transient
overvoltage protection
• UL recognition
D6 only
• Motor phase current switch
selectable from 1 to 6 amps
D12 only
• Motor phase current switch
selectable from 1 to 12 amps
Specifications D6 D12
Dimensions 9.5"H x 5.6"D x 3.8"W 9.7"H x 7.51"D x 13.13"W
Weight 6.5 lb 18 lb
Input Power 90 to 132Vac, 50/60 Hz 90 to 264Vac, 50/60 Hz
Drive Power Dissipation 50 watts (worst case) 200 watts
Operating temperature +32°F to +122°F +32°F to +122°F
Storage temperature -40°F to +167° -40°F to +167°
Humidity 95% Max. noncondensing 95% Max. noncondensing