TABLE OF CONTENTS 1. Safety Instruction 2. Technical Specification 2.1 Beam Angel 3. Lamp 4. How To Set The Unit 4.1 Control Panel 4.2 Main Function 5. How To Control The Unit 5.1 5.2 5.3 5.4 5.5 Master/Slave Built-In Preprogrammed Function. Easy Controller iSolution Operation / Universal DMX Controller DMX 512 Configuration DMX 512 Connection 6. Troubleshooting IM-5S-ELC IM-5W-ELC IM-5S-HID IM-5W-HID 7.
1.Safety Instruction Warning Please read carefully the instruction, which includes important information WARNING about the installation, usage and maintenance. y To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. y Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. y Never touch bulb with bare fingers as it is very hot after using.
2. Technical Specification 3. Lamp • Voltage:AC 120V~60Hz or 230V/240V/250V~50/60Hz In case of replacement of the lamp or maintenance, do not open the fixture • Bulb:HID 150W within 15 minutes until the unit cools down after switching off. ELC 24V 250W • The unit is DMX 512 fixture. It features full DMX 512 control.
HID 150W Lamp Installation Or Replacement 4. How To Set The Unit • Always switch power off before installing or replacing the lamp. Never try to replace the 4.1 Control Panel lamp when it is hot. • Do not touch the bulb with bare hands. Cleaning the lamp with denatured alcohol and wipe with a lint free cloth when lamp is dirty. Display To show the various menus and the selected functions.
4.2 Main Function Show Mode To select any of the given functions, press the MENU button up to when the required one is showing on the display. Select the function by ENTER button and the display will blink. Use Press the MENU button up to when the DOWN and UP button to change the mode. Once the required mode has been selected, button and the display will blink.
ENTER button and the display will blink. Use DOWN and UP button to select the Color Mode Press the MENU button up to when the is showing on the display. Pressing seconds. To go back to the functions without any change press the MENU button again. ENTER button and the display will blink. Use DOWN and UP button to select the (normal) or (Led on) or (Led off) mode.
Stand by 5. How To Control The Unit You can operate the unit in three ways: 1. By master/slave built-in preprogram function Move Spot 2. By easy controller Function 3. By iLead controller ( please refer to the user guide of iLead ) or universal DMX controller No need to turn the unit off when you change the DMX address, as new DMX address Mode setting will be effected at once.
5.4 DMX 512 Configuration 5.5 DMX512 Connection The DMX 512 is widely used in intelligent lighting control, with a maximum of 512 channels. Item Ch 1 Ch 2 Ch 3 Ch 4 Move Spot Pan Tilt Shutter/Sharking Gobo Move Wash Pan Tilt Shutter Ch 5 Ch 6 Ch 7 1 2 3 4 Color No function Color No function Dimmer DMX512 120 ohm 1/4W COMMON 1 INPUT 3 2 DMX + DMX - 1 3 OUTPUT 2 Termination reduces signal errors and to avoid signal transmission problems and interference.
6. Troubleshooting G. If The pan belt is broken Following are a few common problems that may occur during operation. Here are 1. Turn off the main power. 2. Unscrew all the screws (A) and open the base-housing cover (B). 3. Unplug all the connect wires (C) that from the arm to PC board and ignitor. 1. Check the connection of power and main fuse. 4. Unscrew the screws (D) that fix the axis gear (E). 2. Measure the mains voltage on the main connector. 5.
7. Fixture Cleaning Technical Specifications The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics. y Clean with soft cloth using normal glass cleaning fluid. Power AC 120V~60Hz Fuse 20mm Glass T6.