Benutzerhandbuch http://www.ACME-online.de Vers. 1.0 "FlyCamOne", „CamOne”, „zoopa“ sind registrierte Marken von ACME the game company GmbH, Deutschland © copyright 2015 von ACME the game company GmbH Dieses Benutzerhandbuch ist durch internationale Urheberrechtsgesetze geschützt.
Sicherheitshinweise WARNUNG: SERVICE & SUPPORT BEACHTEN SIE FOLGENDE HINWEISE, UM STROMSCHLÄGE ODER SCHÄDEN AM PRODUKT AUSZUSCHLIESSEN: ‐ SETZEN SIE DAS GERÄT NICHT REGEN, FEUCHTIGKEIT, TROPF- ODER SPRITZWASSER AUS ‐ HALTEN SIE DAS GERÄT UND ALLE BESTANDTEILE VON WASSER FERN ‐ VERWENDEN SIE AUSSCHLIESSLICH EMPFOHLENE ZUBEHÖRTEILE ‐ DEMONTIEREN SIE NICHT DAS GERÄT ‐ IM INNERN BEFINDEN SICH KEINE TEILE, DIE VOM BENUTZER GEWARTET WERDEN MÜSSEN - GERÄT UND ZUBEHÖR NICHT STARKER WÄRME AUSSETZEN.
Herzlichen Glückwunsch zu dem Erwerb des zoopa Q Evo 550 Quadrokopters Dieser Quadrokopter, der auf der herausragenden Technologie und den hohen Standards von ACME the game company GmbH beruht, bietet Ihnen Flugerlebnisse auf höchstem Niveau und in bester Qualität. Dieses Benutzerhandbuch wurde speziell entwickelt, um Sie Schritt für Schritt durch die Funktionen und Optionen des Quadrokopters zu führen. Lesen Sie bitte ausführlich die beschriebenen Punkte durch, bevor Sie das Produkt in Betrieb nehmen.
Lieferumfang Überprüfen Sie die Vollständigkeit bevor Sie das Gerät in Betrieb nehmen zoopa Q Evo 550 Modell 1x Fernsteuerung 2,4GHz Landegestell 1xL / 1xR LiPo Ladegerät inkl. Netzkabel 4x Propeller (2x links CCW / 2x rechts CW) 4x Propellerschutz (Bereits beim Modell abgebildet) Micro USB-Kabel Kleinteile Beutel (Schrauben und Werkzeug) 1x LiPo-Akku 11,1V / 3S Benötigtes Zubehör 4x AA-Batterien Mignon 1,5V Wichtige Hinweise! Auf der Internetseite von ACME (http://www.ACME-online.
Inhaltsverzeichnis Sicherheitshinweise………………...………………………………………………………………… Informationen zum enthaltenen LiPo-Akku…….………………….………………………………. Einleitung………………...……………………………………………………………………………. Lieferumfang / Benötigte Komponenten………………………………….………………….….…. Wichtige Hinweise……………………………………………………………………………………. Inhaltsverzeichnis…………..………………...……………………………………………………… Haftungsausschluss und Warnhinweise…………..………………...…………………………….. Vorsichtsmaßnahmen vor jedem Flug……………………………….……………………………..
Vorsichtsmaßnahmen vor jedem Flug Prüfen Sie ob der ordnungsgemäße Zustand und die Funktion aller Bauteile gewährleistet ist Das sich der LiPo-Akku in einem ordnungsgemäßen Zustand befindet Batterien in der Fernsteuerung sowie der Akku im Modell die volle Spannung aufweisen Keine Störquellen das Signal der Fernsteuerung, sowie des GPS-Moduls beeinträchtigen Die Reihenfolge der Inbetriebnahme eingehalten wird: Erst Fernsteuerung und dann das Modell einschalten Die Reihenfolge beim Abscha
Modelleigenschaften und Beschreibung Der zoopa Q Evo 550 wird in einem fast flugfertigen Zustand ausgeliefert, das Modell wurde bereits konfiguriert und getestet. Vor dem Erstflug sind nur noch wenige Handgriffe notwendig.
Erklärung der Fernsteuerung Die Fernsteuerung hat zahlreiche Funktion um den zoopa Q Evo 550 zu bedienen und einzustellen. Linkes Drehpoti „Fence“ (Virtueller Zaun) Linker Kippschalter Linker Steuerknüppel Trimmfunktionen Bindung Steuermode 1 Steuermode 2 Dual Rate Ein-/Aus Schalter Rechtes Drehpoti „Camera Roll“ Rechter Kippschalter Rechter Steuerknüppel Optimierter Anfänger Modus.
Vorbereitung Um den zoopa Q Evo 550 startbereit zu machen, sind nur noch wenige Schritte notwendig. Bereiten Sie sich eine genügend große Unterlage vor und legen Sie sich den kompletten Lieferumfang bereit. Zusätzlich werden noch 4 AA-Batterien 1,5V oder Akkus 1,2V benötigt. --- noch nicht den Akku an das Flugmodell anschließen --1.
Achten Sie auf die richtige Polung beim Einlegen, schieben Sie die Akkufachabdeckung (Rückseite der Fernsteuerung) herunter und legen Sie die Batterien/Akkus ein. Verschließen Sie im Anschluss die Abdeckung. Die Batterien/Akkus sollten nach jedem 10. Flug gewechselt werden! Wenn die Spannung nicht mehr ausreichend ist, piept die Fernsteuerung und die LED blinkt rot. Ein schnelles Piepen signalisiert dass die Fernsteuerung nicht mehr mit ausreichender Spannung versorgt wird.
Leuchten alle LEDs grün, ist der Akku vollständig geladen und kann genutzt werden. Sobald Sie den Akku vorsichtig vom Ladegerät getrennt haben, zeigen die LEDs wieder den Bereitschaftsmodus (abwechselndes Blinken zwischen Grün/Rot) an. HINWEIS: Trennen Sie den Akku vor Abschluss des Ladevorgangs, schaltet das Ladegerät automatisch in den Bereitschaftsmodus um. Sollte das Ladegerät eine Überlastung oder einen Kurzschluß erkennen, wird der Ladevorgang automatisch angehalten.
Anlernen des Kompasses an das Flugfeld System-Kalibrierung = Ausrichtung der Sensoren Um die volle Funktionalität des zoopa Q Evo 550 zu nutzen ist eine einmalige System-Kalibrierung pro Standort notwendig. Nehmen Sie dazu alle Bestandteile des Quadrokopters (Fernsteuerung und voller LiPo-Akku) auf eine freie Fläche (Wiese usw.). Über die Sensoren wird das Magnetfeld der Erde ermittelt. Achten Sie darauf, dass sich keine Magnete (weitere Motoren, Lautsprecher usw.) in der Nähe befinden.
Nach durchgeführten 2 Drehungen ziehen Sie den Akku vom Modell ab. Schließen Sie den Akku wieder an das Modell an, diese Phase wird durch einen zusätzlichen Piep-Ton signalisiert. Der Kompass ist an das Flugfeld angepasst.
10 Punkte bis zum ersten Testflug Beachten Sie unbedingt diese Punkte. Diese erleichtern Ihnen den zoopa Q Evo 550 sicher und erfolgreich zu starten und zu fliegen. 1. Abschluss einer Modellflugversicherung* Seit dem Jahr 2005 ist für den Modellflug eine Versicherung PFLICHT. Informationen dazu erhalten Sie bei Ihrem örtlichen Modellbauverein oder Händler und über den „Deutschen Modellflieger Verband“. Ggf. ist die Abdeckung bereits in Ihrer Haftpflichtversicherung enthalten, bitte erkundigen Sie sich 2.
Bedienung der Fernsteuerung und des Modells Nehmen Sie bitte folgende Einstellungen an der Fernsteuerung (Mode2 = Gas links) vor: Knüppel links > mittig Linker oberer Schalter > 0 Knüppel rechts > mittig Rechter oberer Schalter > 0 Fernsteuerung (Mode 2) ( Modell Ausrichtung Front) Aktion Der linke Knüppel (vor/zurück) der Fernsteuerung steuert die Motorendrehzahl und damit den Steigund Sinkflug des Modells. Mittig hält das Modell die aktuelle Flughöhe.
Fixed height Lock Evo Mode Home Um eine Funktion auf der linken Seite zu aktivieren, beachten Sie das der rechte Schalter auf 0=Fixed height gestellt ist. L0 + R0: Startmodus ohne GPS L1 + R0: kein Sinkflug möglich L2 + R0: Startpunkt orientiertes Fliegen Fence = Virtueller Zaun Diese Funktion begrenzt die Flugdistanz in der Horizontalen auf 150 Meter und in der Senkrechten auf 80 Meter. Camera Roll Über dieses Drehpoti ist es möglich einen optionalen Kameragimbal in seiner Tilt Achse zu steuern.
Um das Modell im Flug zu steuern, können Sie mit den verschiedenen Steuerbefehlen (s.h. Punkt „Bedienung der Fernsteuerung und Modell“) die gewünschte Flugposition einnehmen. Unterspannungs-Schutz Die Flugdauer ist abhängig von Ihren Flugmanövern. Verringert sich im Flug die Akku-Spannung vom Quadrokopter auf ein Minimum, aktiviert sich automatisch die: 1. Stufe des Unterspannungsschutzes. Die LEDs blinken rot, fliegen Sie zügig zu Ihrem Startpunkt zurück und landen Sie schnellstmöglich.
Fail Safe/ Auto Home = Automatisierte Landung Bei einem Signalverlust verfügt der zoopa Q Evo 550 über die Fail Safe Funktion. Dieses bewirkt eine Rückkehr zum Startpunkt mit automatisierter Landung. Wann wird der Fail Safe ausgeführt? Reißt die Verbindung von der Fernsteuerung (defekt, Ausschalten oder Spannung zu niedrig) zum Quadrokopter ab, wartet dieser 10 Sekunden auf ein kommendes Steuersignal. Bleibt dieses aber aus, steigt der zoopa Q Evo 550 auf 20 Meter Flughöhe und kehrt zum Startpunkt zurück.
Firmware Updates Um das Modell auf den aktuellen Stand zu halten, besuchen Sie unsere Homepage. http://www.ACME-online.de Auf der Seite erhalten Sie zahlreiche Informationen usw. Klappe und Action --- zoopa Q Evo 550 Movie FPV – First Person View Bauen Sie Ihren zoopa Q Evo 550 zum FPV-Quadrokopter um. Rüsten Sie eine HD-Kamera nach, erweitern Sie diese mit einem Videotransmitter, Bildschirm/Videobrille und seien Sie der Pilot an Bord.
Über das Drehpoti „Camera Roll“ lässt sich ein angebauter Kamera Gimbal steuern. Um 45° nach oben und um 130° nach unten Da wir höchste Ansprüche als Ansporn sehen, haben wir eine Lösung entwickelt, die ideal miteinander harmoniert und ausgezeichnete Ergebnisse liefert.
zoopa Q Evo 550 Ersatz- / Zubehörteile Beachten Sie bitte, dass nur originale Teile die volle Funktion und Garantieansprüche leisten.
FAQ Problem Die Fernsteuerung reagiert nicht Abhilfe • Batterien/Akkus in der Fernsteuerung prüfen • Polung der Batterien/Akkus in der Fernsteuerung überprüfen • Ein-/Aus-Schalter betätigt? Die Fernsteuerung deutet nach dem Ein- • Ersetzen Sie die Batterien/Akkus schalten oder nach kurzem Betreib • Verwenden Sie hochwertige Alkaline-Batterien Unterspannung an Motoren lassen sich bei vollständig gela- •Steuerknüppel sind mechanisch blockiert und erreichen die Endstellung in der jeweils inneren/unteren Ecke
Gewährleistung & Garantie Dem Verbraucher wird unbeschadet seiner Mängelansprüche gegenüber dem Verkäufer eine Haltbarkeitsgarantie zu den nachstehenden Bedingungen eingeräumt: » Neugeräte und deren Komponenten, die aufgrund von Fabrikations- und / oder Materialfehlern innerhalb von 24 Monate, ab Kauf einen Defekt aufweisen, werden von ACME the game company GmbH nach eigener Wahl gegen ein dem Stand der Technik entsprechendes Gerät dem Erstkäufer kostenlos ausgetauscht oder repariert.
Manual http://www.ACME-online.de Vers. 1.0 “CamOneTec”, “CarCamOne” and the “FlyCamOne” Logo are registered trademarks of ACME the game company GmbH, Germany © Copyright 2015 ACME the game company GmbH This user manual is protected by international copyright laws.
Safety Advice SERVICE & SUPPORT WARNING: Follow these instruction to prevent damage of the unit: ACME the game company GmbH Boikweg 24 DO NOT USE UNPROTECTED IF RAIN OR WATER. PREVENT CONTACT WITH ANY KIND OF LIQUIDS. 33129 Delbrück Germany USE RECOMMENDED ACCESSORIES ONLY. Tel.: +49 2944 97 383 0 DO NOT DISASSEMBLE. service@ACME-online.de or http://www.ACME-online.de THERE ARE NO INTERNAL PARTS THAT NEED TO ME MAINTENANCE. REPAIRS SHOULD BE CARRIED OUT BY QUALIFIED PERSONNEL ONLY.
Thank you for choosing the zoopa Q Evo 550 Quadrocopter This quadrocopter is based on the exceptional technology and high standards of ACME and offers flight experience at the highest level and best quality. This user manual has been specially designed to guide you step by step through the functions and options of the quadrocopter. Please read the following information carefully before using the product.
Content of the box Please check the completeness before using the product. zoopa Q Evo 550 model 1 Controller Landing gear 1xL + 1xR LiPo Charger incl. Power cable 4 Rotors (2 left / 2 right) 4 rotor protectors Micro USB cable Small pieces 1 LiPo-battery 11.1V 3S Required accessories 4 AA-batteries 1.5V Important notice! On our ACME website (http://www.ACME-online.de) more advice, notes and updates are available.
Index Safety Advice……...………………...…………………………………………………………………….. Information on the contained LiPo battery. …….………………….…………………………………… Introduction……………...…………………………………………………………………………………. Content of the box/required components…..…………………………….………………….….………. Important notes….…………………………………………………………………………………………. Index……………..………………………………………………………………………………………….. Disclaimer and warnings……………….…………..………………...…………………………………… Precautions before very flight………...……………………………….………………………………….
• Improper handling of the charging units • losses during the flight of the model Precautions before each flight • Check if the proper condition and operation of all components is ensured • The LiPo battery is in a proper condition as well • batteries inside the remote control have neither nor the model the full battery voltage Interfere with the signal from the remote control and the GPS module • No sources of interference • The order of operation is observed: only remote control and then switch on the mod
Controller features The controller offers various possibilities to control and modify the zoopa Q Evo 550. Optimized beginner mode.
3. Controller batteries The controller requires 4pcs. AA-batteries 1.5V or rechargeable batteries with 1.2V. Please only use new and valuable batteries. Check the polarity and insert the batteries into the compartment of the controller. Make sure it is safely closed after inserting. The batteries shall be replaced after 10 uses! As soon as the voltage goes down, the controller starts to beep and the LED flashes red. A quick beep signalizes low voltage. Starting the model is not possible then.
Make sure that there is sufficient air circulation and a dry and clean area while charging. !!!Pay attention on the warning- and security notices!!! Connect the power cable to the charger and then to your power outlet (100-240V). Never connect two batteries at once! Once the charger is ready for use, a red/green blinking will appear. Connect the LiPo- batteries balancer cable (white plug) with the chargers front port.
Rotor protectors Rotor protectors are included. They differ in A/B remarks. The marks are placed between the two screw bits. Rotorprection A = Silver cap Rotorprotection B = Black cap Unmount the 2 screws that hold the white LED board on the arm. Attach the rotor protection instead and fix it with the screws.
3. Turn around Now adjust the zoopa Q Evo 550 into North direction and turn around the lateral axis, then adjust the zoopa Q Evo 550 into East direction and turn it around the long axis.
After you have performed the 2 turns, disconnect the battery. Then reconnect and wait for the confirmation which is done by a beep. The compass is now adjusted to the flight area. 10 Steps before flight Do not ignore these points. They ease you to start and fly the model safely. 1. Sign a Model-flight insurance: Since 2005, an insurance for RC models is required. Obtain information from your local RC club or dealer and through the local model association. 2.
Controls Please perform the following settings on the controller (Mode2 = Gas left): Left stick > center Upper left switch > 0 Right stick > center Upper right switch > 0 Controller (Mode 2) ( Model front) Action The left stick (front / back) of the controller controls the motor speed and thus the ascent and descent of the model. In the center, the model holds the current altitude. Yaw The left stick (left or right) turns the model around the vertical axis.
Fence = Virtual Fence This mode limits the distance on 150m on the horizontal and 80m on the vertical line. Camera Roll This rotary switch enables a tilt axis control of an optional camera gimbal. First flight To have the full support while flying, we recommend to activate GPS. Switches have to be set as followed: Left 0 + Right 1 Also check the previous section „10 points before flight“ Beginners! Activate the D/R button after you have switched on the controller.
Now switch on the GPS- mode, left switch = 0 / right switch = 1. Slowly lift up the left stick. The model takes off. For details on how to control the model in the air, please check the section „Controls“. Undervoltage protection The flight time depends on your flight attitude. If the battery voltage decreases to it’s minimum, the 1st stage of the undervoltage protection will be automatically activated. The LEDs flash red, fly back and land as fast as possible. This will be performed from 10.8V.
Fail Safe/ Auto Home = Automated landing In case of signal loss, the zoopa Q Evo 550 features a Fail Safe mode. This causes a return to the starting point with automated landing. When will the Fail Safe be performed? If the controller signal (defect, switch off or low voltage) is lost, the quadrocopter waits 10 seconds for incoming commands. If no commands given, the zoopa Q Evo 550 rises onto 20m height and returns to the starting point. It waits another 10 seconds and then starts landing.
Firmware Updates To keep the model up to date, visit our homepage: http://www.ACME-online.de The page also offers further and detailed information. Action! --- zoopa Q Evo 550 Movie FPV – First Person View Turn your zoopa evo into a FPV-quadrocopter. Add a HD-camera, expand it with a video transmitter, screen/video goggles and be the pilot aboard. The so- called FPV flight (First-Person-View/ flying from pilots view) belongs to the specialty events in RC modeling and becomes more famous every day.
The rotary switch „Camera Roll“ enables Gimbal control, max. values are 45° upwards and 130° downwards. Highest aspirations are our motivation. Therefore we have developed a solution that harmonizes perfectly and delivers excellent results. Following options are available: -CamOne Infinity (COIN01) 1080p Full-HD, integrated display and Live-Video Out are only a few highlights of the flagship http://www.CamOneTec.
zoopa Q Evo 550 Spares- / Accessories Please note that only original parts grant full functionality and warranty. Art. No. Description EAN-No.
FAQ Problem Solution The controller does not react to any • Check the controller batteries commands • Check the polarity of the batteries • On/Off switch activated? The controller immediately undervoltage after activation shows • Replace the batteries • Use high- quality Alcaline batteries The motors do not react at fully charged •The control sticks are mechanically blocked and do not reach the end positions in the corner/center battery The quadrocopter shows undervoltage •Check the batteries voltage.
Manuel d’utilisation http://www.ACME-online.de Vers. 1.0 Ce manuel d’utilisation est protégé par les lois internationales du droit à la reproduction. Aucune partie de ce manuel ne peut être utilisée sans l’autorisation préalable de la société ACME the game company. La reproduction, l’enregistrement, la traduction d’une ou de plusieurs parties de ce manuel doit faire l’objet d’une autorisation préalable.
Conseils de sécurité Avertissements: Il est indispensable de suivre les instructions ci-après afin d’éviter d’endommager votre caméra: SERVICE & SUPPORT ACME the game company GmbH Boikweg 24 -NE PAS UTILISER LE PRODUIT EN CONDITIONS PLUVIEUSES. -N’UTILISER QUE LES ACCESSOIRES COMPATIBLES -NE PAS TENTER DE DEMONTER -AUCUN COMPOSANT INTERNE NE NECESSITE D’ENTRETIEN PARTICULIER -LES REPARATIONS NE DOIVENT ETRE FAITES QUE PAR LE PERSONNEL QUALIFIE.
La caméra CamOne infinity et la nacelle ne sont pas incluses. Contenu de la boite Assurez-vous que le produit est complet avant de commencer à l’utiliser Modèle zoopa Q Evo 550 1 Télécommande Train d’atterrissage Chargeur LiPo avec câble secteur 4 Hélices (2 Droites / 2 gauches) 1 Set de protections hélice Cordon micro USB Petits éléments 47 1 Batterie LiPo 3S 11.
Accessoires nécessaires 4 x Piles de type AA- 1.5V Remarque importante! Sur notre site internet ACME (http://www.ACME-online.de), sont disponibles plus de conseils et d’informations sur les mises à jour éventuelles. Vous devez toujours vous référer au manuel d’utilisation lors du montage ou de la mise en route de votre modèle Sommaire Conseils de sécurité………………………...……………………………………………………………. Information sur la batterie livrée avec le modèle………………….…………………………………… Introduction……………...………………….
Limite de responsabilité et avertissements Limite de responsabilité et avertissements Merci de lire ce qui suit avant de débuter l’utilisation du modèle ou de l’un de ses composants! La mise en fonctionnement du modèle équivaut à l’acceptation des clauses de limite de responsabilité ainsi que des instructions d’utilisation. L’utilisation de ce modèle n’est pas recommandée au moins de 18 ans! Vous devez monter le modèle selon les instructions du manuel.
• Conserver à l’écart de l’eau, de la chaleur, ou de toute autre source susceptible d’affecter la batterie ou de la mettre en court-circuit • N’utiliser que le chargeur d’origine • Ne pas tenter d’ouvrir ou de modifier la batterie • NE PAS METTRE EN COURT CIRCUIT • En cas d’émanation de gaz ou de liquide, vous ne devez pas toucher la batterie • Une mauvaise utilisation peut être à l’origine de problème de santé • Les batteries usagées doivent être ramenées dans un centre de valorisation adapté • La batterie
Fonctions de la télécommande La télécommande permet différentes possibilités de contrôle afin de modifier le comportement du zoopa Q Evo 550. Optimisé pour les débutants. Limite la zone de vol.
Utiliser les 4 vis 12x2.5 mm pour sécuriser l‘ensemble. Utiliser pour cela le tournevis livré avec le modèle. Le trou du milieu n’est pas utilisé. 2. Rotors Préparer les 4 rotors. Le sens de rotation de chacun d’entre eux est variable. 2 moteurs tournent vers la gauche (CCW)- et 2 moteurs tournent vers la droite (CW). Chaque rotor est équipé d’un symbole qui permet une identification facile. Chacun d’entre eux a une couleur différente.
Chargeur de batteries et procédure de charge Un chargeur de haute qualité est livré avec le quadrocoptère zoopa Q Evo 550. Il vous permettra de charger et d’entretenir votre batterie.. Vous trouverez ci-après les informations nécessaires à sa bonne utilisation N’utilisez que les batteries d’origine de la marque ACME prévues pour le zoopa Q Evo 550.
-Vous devez recharger la batterie tous les trois mois si vous ne l’utilisez pas régulièrement Le non respects de ces conseils pourrait entrainer une perte d’efficacité de votre batterie. Voltage de la batterie : Batterie chargée à 100%: Chaque élément est chargé à environ 4.2V pour un voltage total de 12.6V Batterie chargée à 90% : Chaque élément est chargé à environ 4.0V pour un voltage total de 12.0V Batterie chargée à 75% : Chaque élément est chargé à environ 3.9V pour un voltage total de 11.
Ajustement du module compass selon la zone de vol Calibration du système = Ajustement du capteur Pour utiliser toutes les fonctionnalités du Zoopa Q Evo 550 une calibration par zone géographique est nécessaire. Prenez les différents composants du modèle (télécommande et batterie LiPo chargée) et placez-vous dans une zone sans obstacle (champs, etc.). Le capteur va alors détecter les champs magnétiques de la terre. Assurez-vous qu’aucun autre aimant (moteur, hautparleur) ne soit à proximité.
Une fois que vous avez effectué ces deux manipulations, vous devrez déconnecter la batterie. Connecter à nouveau la batterie et attendre le signal sonore vous confirmant la bonne prise en compte des nouveaux paramètres. Le module compass est à présent calibrer pour la zone de vol. 10 Etapes importantes avant votre premier vol Ne pas ignorer ces étapes qui vous permettront de débuter l’utilisation de votre Evo en toute simplicité. 1.
Contrôles Merci de procéder comme indiqué ci-après pour le réglage de la télécommande (Mode2 = Gaz à gauche): Manche de gauche > au centre Interrupteur haut gauche > 0 Manche de droite > au centre Interrupteur haut droit > 0 Télécommande (Mode 2) ( Modèle avant) Action Le manche de droite de la télécommande (avant / arrière) contrôle la vitesse de rotation des moteurs et donc la montée et descente du modèle. En position centrale, ce manche permet de conserver le modèle à une altitude constante.
L’imitateur de périmètre = barrière virtuelle Ce mode limite le périmètre de vol à 150m horizontalement et 80 mètres verticalement. Rotation de la caméra Ce potentiomètre permet d’orienter la caméra via la nacelle optionnelle. Premier vol Pour pouvoir bénéficier d’un vol avec le maximum d’assistance, nous vous recommandons d’activer le mode GPS.
Protection contre le sous voltage Le temps de vol dépend de la façon dont vous allez piloter le modèle. Si la batterie passe en dessous de son voltage minimum, une première protection contre le sous voltage va s’activer. Une fois le seuil critique atteint, un témoin LED rouge va alors se mettre à clignoter. Vous devez alors vous poser dès que possible. Dans un second temps, le modèle va alors se poser automatiquement.
En utilisant l‘interrupteur „Auto Home“, le zoopa Q Evo 550 (interrupteur de gauche = 0 / droit = 2) va retourner à sa position de départ et atterrir. Auto Home Mode périmètre limité C’est un mode qui facilite l’apprentissage des débutants. Le modèle est alors limité et ne peut dépasser 150 mètres d’éloignement horizontal et 80 mètres d’éloignement vertical. Ces distances sont calculées depuis le point de départ.
Action! --- zoopa Q Evo 550 Movie FPV – First Person View Faites de votre zoopa Q evo un quadrocoptère FPV. Pour cela il vous suffit d’ajouter une caméra HD combinée à un transmetteur vidéo et un écran ou des lunettes pour simuler la vue du pilote embarqué. Ce qu’on appelle FPV (First-Person-View/ voler depuis la place du pilote embarqué) est une des spécialités des modélistes qui est de nos jours de plus en plus populaire.
Nous aimons proposer des solutions complètes et vous proposons en option en ensemble complet qui offre de très bons résultats. Les options suivantes sont disponibles: -CamOne Infinity (COIN01) Caméra 1080p Full-HD, avec écran intégré, sortie Vidéo, plus de détails sur notre produit phare sur le site http://www.CamOneTec.
Accessoires et pièces du zoopa Q Evo 550 Seules les pièces d’origine permettent une utilisation optimale du modèle et un maintien de la garantie Art. No. Description EAN-No.
FAQ Problème Solution La télécommande ne répond à aucune • Vérifier les piles commande • Vérifier la bonne polarité • L’interrupteur On/Off n’est pas dans la bonne position? La télécommande montre un niveau de • Changer les piles batterie insuffisant dès la mise en • N’utiliser que des piles Alcaline de haute qualité marche Les moteurs ne réagissent pas lorsque •Le manche de l’accélérateur n’est pas dans la bonne position et empêche l’initialisation du modèle la batterie est complètement chargée Le quadro