FPC 6065 / 6084 User Manual FPC6065: 6.5” Industrial Panel PC with AMD Geode LX 800 500MHz processor FPC6084: 8.4” Industrial Panel PC with AMD Geode LX 800 500MHz processor 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
FPC 6065 / 6084 COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
FPC 6065 / 6084 Table of Contents CHAPTER 1 INTRODUCTION 1.1 FPC6065/ FPC6084 FLAT PANEL PC OVERVIEW .................................................... 2 1.1.1 Model Variations ................................................................................................ 2 1.1.2 Applications ....................................................................................................... 2 1.1.3 Standard Features .....................................................................................
FPC 6065 / 6084 2.4 ETHERNET CONTROLLER SPECIFICATIONS........................................................... 17 2.4.1 Overview ........................................................................................................... 17 2.4.2 Features ........................................................................................................... 17 2.5 PERIPHERAL DEVICE INTERFACES, CONNECTORS, AND SLOTS .................... 18 2.5.1 OEM Options .............................................
FPC 6065 / 6084 3.9 COMPACTFLASH® CARD INSTALLATION .............................................................. 34 3.9.1 FPC6065 CF Card Installation ...................................................................... 34 3.9.2 FPC6084 CF Card Installation ...................................................................... 36 3.10 MEMORY MODULE INSTALLATION ......................................................................... 37 3.11 SATA - ALI RAID DRIVER INSTALLATION ..........................
FPC 6065 / 6084 5.1.1 Starting Setup ................................................................................................... 58 5.1.2 Using Setup ...................................................................................................... 58 5.1.3 Getting Help ..................................................................................................... 59 5.1.4 Unable to Reboot After Configuration Changes.............................................. 59 5.1.5 Main BIOS Menu ...
FPC 6065 / 6084 C.2.2 Cleaning Tools................................................................................................114 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
FPC 6065 / 6084 CHAPTER 1 INTRODUCTION 1.1 FPC6065/ FPC6084 FLAT PANEL PC OVERVIEW The FPC 6065/ FPC6084 flat panel PC is a flexible, multi-functional flat panel PC that can be applied in diverse operational environments and implemented in multi-faceted applications. The FPC6065/ FPC6084 Comes fully kitted with a high-performance motherboard and a host of other peripheral interface connectors. The FPC6065/ FPC6084 is designed for ease of use and easy installation. 1.1.
FPC 6065 / 6084 -Aluminum die-casting IP65 industrial panel -Dual 10/100Mbps Ethernet support -One CompactFlash® Type I/II socket support -Simplified installation process -RoHS compliance 1.2 EXTERNAL OVERVIEW 1.2.1 GENERAL DESCRIPTION The FPC6065/FPC6084 flat panel PC is a rectangular cubic structure that comprises of a screen, rear panel, top panel, bottom panel and two side panels (left and right). An aluminum frame surrounds the front screen.
FPC 6065 / 6084 1.2.3 REAR PANEL The rear panel provides access to a fan ventilation vent and retention screw holes that support the wall mounting (circled in red) and DIN rail mounting (circled in blue). Refer to Figure 1-2 and Figure 1-3. FIGURE 1-2: FPC6065 REAR VIEW FIGURE 1-3: FPC6084 REAR VIEW 1.2.4 TOP PANEL The top panel of FPC6065 provides access to two retention screw holes that support to secure the back cover to the chassis. The retention screw holes are circled in Figure 1-4 below.
FPC 6065 / 6084 FIGURE 1-4: FPC6065 TOP VIEW FIGURE 1-5: FPC6084 TOP VIEW 1.2.5 BOTTOM PANEL The bottom panel of the FPC6065/FPC6084 has the following I/O interfaces (Figure 1-6 and Figure 1-7): 1 x Serial port (COM) connector 1 x PS/2 keyboard/mouse connector 1 x AC power adapter connector 1 x VGA connector 2 x RJ-45 10/100Mbps Ethernet connectors 2 x USB 2.0 connectors 1 x Power switch Audio jacks FIGURE 1-6: FPC6065 BOTTOM VIEW 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.
FPC 6065 / 6084 FIGURE 1-7: FPC6084 BOTTOM VIEW 1.3 INTERNAL OVERVIEW The FPC6065/FPC6084 internal components are configured in a two level format. The motherboard and 2.5" HDD are installed on a metal sheet that protects the rear of the TFT LCD screen. Below the metal sheet is a circuit board that is connected to the screen and the motherboard. 1.4 SPECIFICATIONS 1.4.
FPC 6065 / 6084 1.4.2 SYSTEM SPECIFICATIONS The technical specifications for the FPC6065 and FPC6084 systems are listed in Table 1-2. 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
FPC 6065 / 6084 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
FPC 6065 / 6084 1.4.3 MOTHERBOARD SPECIFICATIONS The FPC6065 and FPC6084 both come with a WAFER-LX motherboard. The technical specifications of the motherboard are listed in Table 1-3. 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
FPC 6065 / 6084 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
FPC 6065 / 6084 1.4.4 FLAT PANEL SCREEN 1.4.4.1 FPC6065 FLAT PANEL SCREEN SPECIFICATIONS The FPC6065 comes with a 6.5" TFT LCD monitor at the front of the flat panel PC (see Figure 1-1). The specifications for the LCD monitor are shown in Table 1-4 below. 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice.
FPC 6065 / 6084 1.4.4.2 FPC6084 FLAT PANEL SCREEN SPECIFICATIONS The FPC6084 comes with a 8.4" TFT LCD monitor at the front of the flat panel PC (see Figure 1-1). The specifications for the LCD monitor are shown in Table 1-5 below. 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice.
FPC 6065 / 6084 1.5 DIMENSIONS 1.5.1 FPC6065 DIMENSIONS The dimensions of the FPC6065 flat panel PC are shown in Figure 1-8 below. FIGURE 1-8: FPC6065 DIMENSIONS (UNITS IN MM) 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
FPC 6065 / 6084 1.5.2 FPC6084 DIMENSIONS The dimensions of the FPC6084 flat panel PC are shown in Figure 1-9 below. FIGURE 1-9: FPC6084 DIMENSIONS (UNITS IN MM) 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
FPC 6065 / 6084 CHAPTER 2 WAFER-LX MOTHERBOARD 2.1 INTRODUCTION The FPC6065 and FPC6084 flat screen PC both contain the WAFER-LX motherboard. The motherboard is the heart of any computer and is responsible for transmitting, receiving and processing data as well as driving the different onboard devices. This chapter gives a brief introduction to the WAFER-LX motherboard. For more complete details on the connectors and the different implementations of the WAFER-LX, please refer to the WAFER-LX user guide.
FPC 6065 / 6084 VESA 1.1 and 2.0 VIP/VDA support 0.13 micron process 481-terminal PBGA (Plastic Ball Grid Array) with internal heatspreader 2.2.2 AMD® Geode™ LX 800 500MHz Power Management The power management for the 500MHz AMD® Geode™ LX 800 is listed below: 1.8W Typical (3.9W TDP) @ 500MHz GeodeLink active hardware power management Hardware support for standard ACPI software power management I/O companion SUSP#/SUSPA# power controls Lower power I/O Wakeup on SMI/INTR 2.
FPC 6065 / 6084 Flash Interface o Multiplexed with IDE interface Connects to an array of industry standard NAND Flash and/or NOR Flash USB Controller o 4 USB ports o Supports both USB 1.1 and USB 2.0 o 3 host ports o 1 host/device Audio Codec 97 (AC97) Controller o AC97 specification v2.
FPC 6065 / 6084 2.4 ETHERNET CONTROLLER SPECIFICATIONS 2.4.1 OVERVIEW The Realtek RTL8100C(L) is a highly integrated and cost-effective single-chip Fast Ethernet controller. It is enhanced with an ACPI (Advanced Configuration Power Interface) management function for PCI in order to provide efficient power management for advanced operating systems with OSPM (Operating System Directed Power Management).
FPC 6065 / 6084 2.5.2 INTERNAL SLOTS The slots listed below can all be found on the WAFER-LX motherboard. 1 x 200-pin DDR SO-DIMM socket 1 x CFII slot 2.5.3 INTERNAL PERIPHERAL DEVICE CONNECTORS The peripheral device connectors listed below are located on the WAFER-LX motherboard. Pinouts for these connectors can be found in Appendix A.
FPC 6065 / 6084 1 x Parallel port connector 1 x Reset button connector 1 x RS-232/422/485 serial port connector 2 x SATA connectors 1 x Suspend power input connector 1 x TFT LCD LVDS interface connector 1 x TFT LCD TFT interface connector 1 x USB connector 1 x SO-DIMM socket 2.5.4 EXTERNAL PERIPHERAL DEVICE CONNECTORS The peripheral device connectors listed below are located on the rear panel of the WAFER-LX motherboard. Pinouts for these connectors can be found in Appendix A.
FPC 6065 / 6084 CHAPTER 3 INSTALLATION AND CONFIGURATION 3.1 INSTALLATION PRECAUTIONS When installing the flat panel PC, please follow the precautions listed below: Power turned off: When installing the flat panel PC, make sure the power is off. Failing to turn off the power may cause severe injury to the body and/or damage to the system. Certified Engineers: Only certified engineers should install and modify onboard functionalities. Mounting: The flat panel PC is a heavy device.
FPC 6065 / 6084 3.3 INSTALLATION AND CONFIGURATION STEPS The following installation steps must be followed. Step 1: Unpack the flat panel PC Step 2: Set the jumper settings Step 3: Install system fan Step 4: Install HDD Step 5: Install the SO-DIMM memory module Step 6: Mount the flat panel PC Step 7: Connect peripheral devices to the bottom panel of the flat panel PC Step 8: Configure the system 3.
FPC 6065 / 6084 3.4.
FPC 6065 / 6084 3.4.
FPC 6065 / 6084 3.5.2 FPC6084 BACK COVER REMOVAL The back cover is secured to the chassis with seven retention screws on the rear panel (Figure 3-2). Remove the seven retention screws and lift the cover off the FPC6084. 3.6 JUMPER SETTINGS A jumper is a metal bridge that is used to close an electrical circuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them.
FPC 6065 / 6084 3.6.1 JP1: AT POWER SELECT JUMPER SETTINGS The AT/ATX Power Mode Select jumper specifies the systems power mode. 3.6.2 CN7: CLEAR CMOS SETUP NOTE: The battery connector (CN7) is used as the clear CMOS jumper on the motherboard. If the motherboard fails to boot due to improper BIOS settings, use this jumper to clear the CMOS data and reset the system BIOS information. To do this, use the jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2.
FPC 6065 / 6084 Enter the correct CMOS setting Load Optimal Defaults Load Failsafe Defaults. After one of the above has been done, save the changes and exit the CMOS Setup menu. 3.6.3 JP2: COM3 SETUP JUMPER SETTINGS The COM3 port can be configured as an RS-422 serial port or as an RS-485 serial port. 3.7 SYSTEM FAN INSTALLATION 3.7.1 FPC6065 SYSTEM FAN INSTALLATION Step 1: The fan bracket of the FPC6065 is secured to the chassis with three retention screws inside the chassis (Figure 3-4).
FPC 6065 / 6084 Step 2: Install the system fan module to the fan bracket with four retention screws (Figure 3-11). Step 3: Use a cable tie to tie the system fan module cables as shown in Figure 3-6. Step 4: Locate the fan connector (CN4) on the motherboard (Figure 3-7). Insert the fan connector of the fan module to the fan connector on the motherboard. 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved.
FPC 6065 / 6084 Step 5:Reinstall the fan bracket into the system using the three previously removed retention screws. 3.7.2 FPC6084 SYSTEM FAN INSTALLATION Step 1: Install the system fan module to the fan bracket with four retention screws (Figure 3-11). Step 2: Attach the cable clip on the fan bracket as shown in Figure 3-6. Secure the fan cable with the cable clip. 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved.
FPC 6065 / 6084 Step 3: Locate the fan connector (CN4) on the motherboard (Figure 3-7). Insert the fan connector of the fan module to the fan connector on the motherboard. Step 4: Install the fan bracket into the system with two retention screws. 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice.
FPC 6065 / 6084 3.8 HDD INSTALLATION 3.8.1 FPC6065 HDD INSTALLATION To install the HDD into the FPC6065, please follow the steps below: Step 1: Remove the back cover. See Section 3.5.1 above. Step 2: Remove HDD bracket from the platform. See Section 3.7.1 Step 1. Step 3: Attach the HDD brackets to the HDD. To do this, align the four retention screw holes in the both sides of the HDD bracket with the retention screw holes on the sides of the HDD.
FPC 6065 / 6084 Step 4: Connect the IDE/SATA cable from the IDE/SATA connector on the otherboard to the rear of HDD. Reconnect the fan cable to the motherboard. Step 5: Install the HDD into the FPC6065 by aligning the retention screw holes in the HDD brackets with the retention screw holes on the chassis. Insert the three retention screws. 3.8.2 FPC6084 HDD INSTALLATION To install the HDD into the FPC6084, please follow the steps below: Step 1: Remove the back cover. See Section 3.5.2 above.
FPC 6065 / 6084 Step 4:Connect the IDE/SATA cable from the IDE/SATA connector on the motherboard to the rear of HDD. Step 5: Install the HDD into the FPC6084 by aligning the retention screw holes in the base of the HDD brackets with the retention screw holes on the platform. Insert the four retention screws. 3.9 COMPACTFLASH CARD INSTALLATION 3.9.1 FPC6065 CF CARD INSTALLATION The FPC6065 embedded motherboard has one CF Type II slot on the solder side.
FPC 6065 / 6084 Step 4: Remove the four retention screws that secure the motherboard to the chassis (Figure 3-16). Step 5: Remove the copper pillar that secures the motherboard to the chassis (Figure 3-17). Step 6: Lift the chassis up and locate the CF slot. Insert a CF card into the slot (Figure 3-18). 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved.
FPC 6065 / 6084 Step 7: Secure the motherboard with the copper pillar first. Then, Insert all previously removed retention screws into the FPC6065 to secure the motherboard and the chassis. Remember to connect the grounding cable when inserting the retention screw to the copper pillar (Figure 3-19). Step 8: Install the previously removed HDD bracket and reconnect the fan cable. Step 9: Replace the top cover. Once replaced reinsert the six previously removed retention screws. 3.9.
FPC 6065 / 6084 Step 3: Remove the four retention screws on the bottom panel (Figure 3-15). Step 4: Remove the six retention screws inside the chassis (Figure 3-16). Step 5: Lift the chassis up and locate the CF slot. Insert a CF card into the slot (Figure 3-18). 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice.
FPC 6065 / 6084 Step 6: Insert all previously removed retention screws into the FPC6084 to secure the chassis. Step 7: Install the previously removed HDD bracket. Step 8: Replace the top cover. Once replaced reinsert the six previously removed retention screws. 3.10 MEMORY MODULE INSTALLATION The flat panel PC embedded motherboard has one 200-pin SO-DIMM socket. To install the SO-DIMM module, follow the instructions below. Step 1: Remove the back cover. See Section 3.5 above.
FPC 6065 / 6084 3.11 SATA-ALi RAID DRIVER INSTALLATION CAUTION! Because of the inherent limitations by AMD Geode CS5536 chipset, the ALi M5283 SATA and RAID controller is implemented as a device that requires device driver during the Windows installation process. To successfully install the device driver, please carefully read the following instructions. The ALi driver is especially required if SATA drives are the only hard disk drives in the FPD6065/FPC6084 system.
FPC 6065 / 6084 Step 6: The setup program continues, later when the setup program prompts users to specify additional adapters, please press the S key. Step 7: The setup program prompts user to insert the driver diskette. Please insert the driver diskette, and press ENTER to continue. Step 8: The follow-up window lists out the installation choices, please select ALi SATA/RAID Controller for Windows XP and press ENTER to continue.
FPC 6065 / 6084 Step 7: Please "confirm" the Digital Signature Not Found window when it appears, when finished, please restart the computer. Step 8: Repeat step 1, but select ALi ATA/RAID Controller at step 4. 3.12 MOUNTING THE SYSTEM WARNING! When mounting the flat panel PC onto an arm, onto the wall or onto a panel, it is better to have more than one person to help with the installation to make sure the panel PC does not fall down and get damaged.
FPC 6065 / 6084 Step 5: Secure the mounting-bracket to the wall by inserting the retention screws into the four pilot holes and tightening them (Figure 3-24). Step 6: Insert the four monitor mounting screws provided in the wall mounting kit into the four screw holes on the real panel of the flat panel PC and tighten until the screw shank is secured against the rear panel (Figure 3-25). Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on the bracket. 661 Brea Canyon Rd.
FPC 6065 / 6084 Step 8: Carefully insert the screws through the holes and gently pull the monitor downwards until the monitor rests securely in the slotted holes (Figure 3-26). Ensure that all four of the mounting screws fit snuggly into their respective slotted holes. NOTE: In the diagram below the bracket is already installed on the wall. 3.12.2 PANEL MOUNTING 3.12.2.1 FPC6065 PANEL MOUNTING To mount the FPC6065 flat panel PC into a panel, please follow the steps below.
FPC 6065 / 6084 Step 3: Slide the FPC6065 through the hole until the aluminum frame is flush against the panel. Step 4: Secure the panel mounting clips to either side of the monitor using the retention screws supplied in the mounting kit pack (Figure 3-28). Step 5: Tighten the panel retention screws that pass through the panel mounting clips until the plastic caps at the front of all the screws are firmly secured to the panel (Figure 3-28). 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.
FPC 6065 / 6084 3.12.2.2 FPC6084 PANEL MOUNTING To mount the FPC6084 flat panel PC into a panel, please follow the steps below. Step 1: Select the position on the panel to mount the FPC6084. Step 2: Cut out a section from the panel that corresponds to the rear panel dimensions of the FPC6084. Take care that the panel section that is cut out is smaller than the overall size of the metal frame that surrounds the FPC6084 but just large enough for the rear panel of the FPC6084 to fit through (Figure 3-29).
FPC 6065 / 6084 3.12.3 ARM MOUNTING The FPC6065/FPC6084 is VESA (Video Electronics Standards Association) compliant and can be mounted on an arm with a 100mm interface pad. To mount the FPC6065/FPC6084 on an arm, please follow the steps below. Step 1: The arm is a separately purchased item. Please correctly mount the arm onto the surface it uses as a base. To do this, refer to the installation documentation that came with the mounting arm.
FPC 6065 / 6084 Step 4: Secure the flat panel PC to the interface pad by inserting four retention screws through the bottom of the mounting arm interface pad and into the flat panel PC. 3.12.4 CABINET AND RACK INSTALLATION The FPC6065/FPC6084 flat panel PC can be installed into a cabinet or rack. The installation procedures are similar to the panel mounting installation.
FPC 6065 / 6084 Step 2: Secure the mounting clips to either side of the flat panel PC using the retention screws supplied in the mounting kit pack (Figure 3-33). Step 3: Tighten the panel retention screws that pass through the mounting clips until the plastic caps at the front of all the screws are firmly secured to the rack/cabinet bracket (Figure 3-33). Step 4: Slide the FPC6084 flat panel PC with the attached rack/cabinet bracket into a rack or cabinet (Figure 3-34). 661 Brea Canyon Rd.
FPC 6065 / 6084 Step 5: Once the FPC6084 flat panel PC with the attached rack/cabinet bracket has been properly inserted into the rack or cabinet, secure the front of the rack/cabinet bracket to the front of the rack or cabinet (Figure 3-34). 3.12.4.2 FPC6084 CABINET AND RACK INSTALLATION Step 1: Slide the rear chassis of the FPC6084 flat panel PC through the rack/cabinet bracket until the aluminum frame is flush against the front of the bracket (Figure 3-35).
FPC 6065 / 6084 Step 4: Follow the Step 4 and Step 5 of the FPC6065Cabinet and Rack Installation procedures to complete the whole installation process. 3.12.5 DIN MOUNTING To mount the FPC6065/FPC6084 flat panel PC onto a DIN rail, please follow the steps below. Step 1: Attach the DIN rail mounting bracket to the rear of the panel PC. Secure the bracket to the panel PC with the supplied retention screws (Figure 3-37).
FPC 6065 / 6084 Step 4: Secure the DIN rail to the mounting bracket by turning the top screw clockwise.This draws the lower clamp up and secures the monitor to the DIN rail (Figure 3-40). 3.13 REAR PANEL CONNECTORS 3.13.1 LCD PANEL CONNECTION To connect the FPC6065/FPC6084 flat panel PC to a second monitor, a conventional CRT VGA monitor connector is located on the bottom panel. This panel is a 15-pin, female D-SUB connector. 3.13.
FPC 6065 / 6084 3.13.3 USB Connection The rear panel USB connectors provide easier and quicker access to external USB devices. The rear panel USB connector is a standard connector and can easily be connected to other USB devices. 3.13.4 Keyboard and Mouse Connection One PS/2 connector on the bottom panel facilitates the connection of a mouse and a keyboard.
FPC 6065 / 6084 CHAPTER 4 GASKEY REPLACEMENT 4.1 Gasket Replacement A gasket used for a long time may gradually lose its ability to protect the monitor from fluids and vapors; scratches or dirt may also accumulate. It is recommended that the gasket be replaced yearly. NOTE: If the monitor is mounted vertically, first remove it and place it on a flat, level surface with the display screen facing down before changing the gasket. Step 1: Remove the old gasket from the sides of the monitor.
FPC 6065 / 6084 CHAPTER 5 AMI BIOS SETUP 5.1 Introduction A licensed copy of Phoenix Award BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows users to modify the basic system configuration. This chapter describes how to access the BIOS setup program and the configuration options that may be changed. 5.1.1 Starting Setup The Phoenix Award BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1.
FPC 6065 / 6084 5.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press ESC or the F1 key again. 5.1.4 Unable to Reboot After Configuration Changes If the system cannot be booted after changes are made, restore the CMOS defaults. The CPU card should come with a restore CMOS settings jumper. Refer to Section 3.6.2 for more information. 5.1.
FPC 6065 / 6084 NOTE: The following sections will completely describe the menus listed below and the configuration options available to users. The following menu options are seen in BIOS Menu 1. Standard CMOS Features: Changes the basic system configuration. Advanced BIOS Features: Changes the advanced system settings. Advanced Chipset Features: Changes the chipset configuration features. Integrated Peripherals: Changes the settings for integrated peripherals.
FPC 6065 / 6084 Set User Password Use the Set User Password option to set the user password. By default no user password is set. To install a user password, select this field and enter the password. After this option is selected, a red dialogue box appears with "Enter Password: ". Type the password and press ENTER. Retype the original password into the "Confirm Password: " dialogue box and press ENTER.
FPC 6065 / 6084 5.2 STANDARD CMOS FEATURES Use the Standard CMOS Features BIOS menu (BIOS Menu 2) to set basic BIOS Date [Day mm:dd:yyyy] Use the Date option to set the system date. Time [hh/mm/ss] Use the Time option to set the system time. IDE Master and IDE Slave When entering setup, BIOS auto detects the presence of IDE devices. The Standard CMOS Features menu shows the status of the auto detected IDE devices.
FPC 6065 / 6084 IDE Secondary Slave IDE device configurations are changed or set in the IDE Configuration menu. If an IDE device is detected, and one of the above listed two BIOS configuration options is selected, the IDE configuration options shown in Section 5.2.1 appear. Drive A [None] Use the Drive A/B configuration to specify the floppy drive type installed in the system. The floppy drive configuration options are: None 360K, 5.25 in. 1.2M, 5.25 in. 720K, 3.5 in. 1.44M, 3.5in (Default) 2.88M, 3.5 in.
FPC 6065 / 6084 Base Memory: The Base Memory is NOT user configurable. The POST determines the amount of base (or conventional) memory installed in the system. The value of the base memory is typically 512K for systems with 512K memory installed, or 640K for systems with 640K or more memory installed. Extended Memory The Extended Memory is NOT user configurable. The BIOS determines how much extended memory is present during the POST.
FPC 6065 / 6084 inaccessible and any drives attached to it are undetected. Auto (Default) Setting this option allows the device to be automatically detected by the BIOS. Manual Selecting this option allows manual configuration of the device on the IDE channel in BIOS. Access Mode [Auto] The Access Mode option can only be configured if the BIOS configuration option is set to either Manual or Auto.. Use the Access Mode option to determine the hard disk BIOS translation modes.
FPC 6065 / 6084 Precomp The Precomp specification indicates on what track the write precompensation begins. Landing Zone The Landing Zone specification indicates where the disk head will park itself after the system powers off. Sector The Sector specification indicates how many logical sectors the HDD has been divided into. 5.3 ADVANCED BIO FEATURES Use the Advanced BIOS Features menu (BIOS Menu 3) to configure the CPU and peripheral device configuration options. 661 Brea Canyon Rd.
FPC 6065 / 6084 Virus Warning [Disabled] NOTE: Many disk diagnostic programs can cause the above warning message to appear when the program attempts to access the boot sector table. If you are running such a program, it is recommended that the virus protection function be disabled beforehand. Use the Virus Warning option to enable BIOS to monitor the boot sector and partition table of the HDD for any attempted modification.
FPC 6065 / 6084 Boot From LAN Control [Disabled] Use the BOOT From LAN Control option to enable the system to be booted from a remote system. Disabled (Default) The system cannot be booted from a remote system through the LAN. Enabled The system can be booted from a remote system through the LAN. SATA Boot ROM Control [Disabled] Use the SATA Boot ROM Control option to configure SATA IDE use in DOS mode. Disabled (Default) Enabled Disables SATA IDE use in DOS mode. Enables SATA IDE use in DOS mode.
FPC 6065 / 6084 HDD-1 HDD-2 HDD-3 ZIP100 USB-FDD USB-ZIP USB-CDROM USB-HDD LAN Disabled Boot Other Device [Enabled] Use the Boot Other Device option to determine whether the system uses a second or third boot device if the first boot device is not found. Disabled The system does not look for second and third boot devices if the first one is not found. Enabled (Default) The system looks for second and third boot devices if the first one is not found.
FPC 6065 / 6084 Boot Up Numlock Status [On] Use the Boot Up Numlock Status option to specify the default state of the numeric keypad. Off The keys on the keypad are not activated. On (Default) Activates the keys on the keypad. Gate A20 Option [Fast] Use the Gate A20 Option option to set if the keyboard controller or the chipset controls the Gate A20 switching. Normal The keyboard controller does the switching. Fast (Default) The chipset does the switching.
FPC 6065 / 6084 Typematic Rate (Chars/sec) [6] The Typematic Rate option can only be configured if the Typematic Rate Setting is enabled. Use the Typematic Rate option to specify the rate keys are accelerated.
FPC 6065 / 6084 Security Option [Setup] Use the Security Option to limit access to both the system and Setup, or just Setup. Setup(Default) The system does not boot and access to Setup is denied is not entered at the prompt. if the correct password System The system boots, but access to Setup is denied if the correct password is not entered at the prompt. NOTE: To disable security, select the password setting in the Main Menu.
FPC 6065 / 6084 Delay for HDD (secs) [3] Use the Delay for HDD option to specify the period of time the system should wait before the HDD is identified. If selected, the user is asked to enter a number between 0 and 15. The number specified is the number of seconds the system waits before the HDD is identified. Small Logo (EPA) Show [Disabled] Use the Small Logo (EPA) Show option to specify if the Environmental Protection Agency (EPA) logo appears during the system boot-up process.
FPC 6065 / 6084 CPU Frequency [500MHz] Use the CPU Frequency option to set the CPU frequency. The CPU Frequency options are: Auto 200MHz 333MHz 400MHz 433MHz 500MHz (Default) Memory Frequency [333MHz] Use the Memory Frequency option to set the frequency of the installed DRAM modules. The Memory Frequency options are: 200MHz 266MHz 333MHz (Default) 400MHz CAS Latency [Auto] Use the CAS Latency Time option to set the Column Address Strobe (CAS) delay time. The CAS Latency Time options are: Auto (Default) 1.
FPC 6065 / 6084 Video Memory Size [8M] Use the Video Memory Size option to determine how much memory is allocated to the video graphics device. The Video Memory Size options are: None 8M (Default) 16M 32M 64M 128M 254M Output Display [Panel & CRT] Use the Output Display configuration to specify the display devices the system is connected to.
FPC 6065 / 6084 5.4.1 FLAT PANEL CONFIGURATION Use the Flat Panel Configuration menu (BIOS Menu 5) to set the configuration settings for the flat panel screen connected to the system. Resolution [800 x 600] The Resolution option can only be configured if the Flat Panel Type option is not set to Auto. Use the Resolution option to set the resolution of the flat panel screen connected to the system.
FPC 6065 / 6084 9-24 bits, 1 ppc (Default) 18, 24 bits, 2 ppc Refresh Rate [60Hz] The Refresh Rate option can only be configured if the Flat Panel Type option is not set to Auto. Use the Refresh Rate option to set the screen refresh rate required by the panel connected to the system. Check the documentation that came with the panel before setting this option.
FPC 6065 / 6084 5.5 INTEGRATED PERIPHERALS Use the Integrated Peripherals menu (BIOS Menu 6) to change the configuration options for the attached peripheral devices. On-Chip IDE Channel 1 [Enabled] Use the On-Chip IDE Channel 1 option to specify if the system uses the integrated primary IDE channel or not. Disabled The primary IDE channel is not used. Enabled (Default) The primary IDE channel is used.
FPC 6065 / 6084 IDE UDMA[Auto] Use the IDE UDMA option below to select the Ultra DMA (UDMA) mode for the followingHDDs: IDE Primary Master UDMA IDE Primary Slave UDMA Auto (Default) Disabled The computer selects the correct UDMA. The UDMA for the HDD device is disabled. IT8888 ISA Decode IO Use the IT8888 ISA Decode IO menu (BIOS Menu 7) to set the IO memory range for the onboard ISA. See Section 5.5.1.
FPC 6065 / 6084 Onboard Serial Port 3 [Disabled] Use the Onboard Serial Port 3 option to select the I/O address and IRQ for the onboard serial port 2. The serial port can be disabled or the I/O address and the IRQ can be automatically selected by the BIOS.
FPC 6065 / 6084 ECP Mode Use DMA [1] The ECP Mode Use DMA option is only available if the Parallel Port Mode option is set to ECP mode. Use the ECP Mode Use DMA option to specify the DMA channel the parallel port must use in the ECP mode. 1(Default) The parallel port uses DMA Channel 1 in ECP mode. 3 The parallel port uses DMA Channel 3 in ECP mode. 5.5.1 IT8888 ISA Decode IO Use the IT8888 ISA Decode IO menu (BIOS Menu 7 to set the IO memory range for the onboard ISA. 661 Brea Canyon Rd.
FPC 6065 / 6084 The IT8888 ISA Decode IO menu has the following common options: Decode I/O Space N Decode I/O Speed N Decode I/O Addr. N [15:0] Decode I/O Size N Where N is an integer in the set [1, 2, 3, 4, 5] and represents a set for the PCI-104 devices that are attached to the system. Decode IO Space N [Enabled] Use the Decode IO Space N option to allocate system resources to the ISA bridge and to enable the Nth PCI-104 to function correctly.
FPC 6065 / 6084 5.5.2 IT8888 ISA DECODE MEMORY Use the IT8888 ISA Decode Memory (BIOS Menu 8) to set the resources for the onboard ISA bus. The IT8888 ISA Decode IO menu has the following common options: Decode Memory Space N Decode Memory Speed N Decode Memory Addr. N [15:0] Decode Memory Size N Where N is an integer in the set [1, 2, 3, 4, 5] and represents a memory set for the PCI-104 devices that are attached to the system.
FPC 6065 / 6084 Fast Speed Middle Speed Slow Speed Subtractive Speed Decode Memory Address N [xx] Use the Decode Memory Address N option to allocate an address to the memory of the ISA bus. The address may range from 0001 to FFFF. Decode Memory Size N [xx] Use the Decode Memory Size N option to specify the memory size of the ISA bus. The following options are available: 16 KB 32 KB 64 KB 128 KB 256 KB 512 KB 1 MB 2 MB 5.
FPC 6065 / 6084 ACPI Function [Disabled] Use the ACPI Function to enable the ACPI (Advanced Configuration and Power Interface) function. Disabled Enabled(Default) ACPI function disabled. ACPI function enabled. ACPI Suspend Type [S1(POS)] Use the ACPI Suspend Type BIOS option to specify the sleep state the system enters when not being used. S1 (POS)(Default) System appears off. The CPU is stopped; RAM is refreshed; the system is running in a low power mode. S3 (STR) System appears off.
FPC 6065 / 6084 x Suspend Mode [Disabled] The Suspend Mode option can only be selected if the Power Management option is set to Legacy. The Suspend Mode specifies the amount of time the system can be inactive before the system enters suspend mode.
FPC 6065 / 6084 PNP OS Installed [No] The PNP OS Installed option determines whether the Plug and Play devices connected to the system are configured by the operating system or the BIOS. No (Default) If the operating system does not meet the Plug and Play specifications, BIOS configures all the devices in the system. Yes Set this option if the system is running Plug and Play aware operating sys tems. The operating system changes the interrupt, I/O, and DMA settings.
FPC 6065 / 6084 x IRQ Resources [Press Enter] The IRQ Resources option (BIOS Menu 11) can only be selected if the Resources Controlled By option is set to Manual. The IRQ Resources menu has the following options: IRQ-3 assigned to IRQ-4 assigned to IRQ-5 assigned to IRQ-7 assigned to IRQ-10 assigned to IRQ-11 assigned to The above options all have the following default options.
FPC 6065 / 6084 The menu has two configurable options: Reserved Memory Base Reserved Memory Length Reserved Memory Base [N/A] The Reserved Memory Base option specifies the base address for the peripheral device. The Reserved Memory Base options are: N/A (Default) C800 CC00 D000 D400 D800 DC00 x Reserved Memory Length [8K] The Reserved Memory Length option can only be accessed if the Reserved Memory Base option is not set to N/A.
FPC 6065 / 6084 PCI/VGA Palette Snoop [Disabled] Use the PCI/VGA Palette Snoop option to enable the system to determine whether or not some special VGA cards, high-end hardware MPEG decoders and other similar devices are allowed to look at the VGA palette on the video card so these devices can determine what colors are in use. This option is needed very rarely and should be left "Disabled" unless a video device specifically requires the setting to be enabled upon installation.
FPC 6065 / 6084 CPU Warning Temperature [Disabled] Use the CPU Warning Temperature option to set the CPU temperature that would automatically generate a warning. Disabled(Default) Enabled No warning is issued When the CPU reaches a certain temperature, a new warning is issued System Temperature The following temperatures are monitored: Current CPU Temperature System Fan The following system fans are monitored: Current System Fan Voltages The following voltages are monitored: Vcore +3.
FPC 6065 / 6084 A. INTERFACE CONNECTORS The FPC6065/FPC6084 flat panel PC motherboard, the WAFER-LX, comes with a number of peripheral interface connectors and configuration jumpers listed in Chapter 2. The pinouts for these connectors are listed below: 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice.
FPC 6065 / 6084 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
FPC 6065 / 6084 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
FPC 6065 / 6084 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
FPC 6065 / 6084 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
FPC 6065 / 6084 661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218 © Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
FPC 6065 / 6084 B. BIOS CONFIGURATION OPTIONS Below is a list of BIOS configuration options described in Chapter 5. Load Fail-Safe Defaults .......................................................................................................61 Load Optimized Defaults.....................................................................................................61 Set Supervisor Password....................................................................................................
FPC 6065 / 6084 Boot Up Numlock Status [On] ............................................................................................70 Gate A20 Option [Fast] ........................................................................................................70 Typematic Rate Setting [Disabled].....................................................................................70 Typematic Rate (Chars/sec) [6] ..........................................................................................
FPC 6065 / 6084 Onboard Parallel Port [378/IRQ7] .......................................................................................81 Parallel Port Mode [SPP] .....................................................................................................81 EPP Mode Select [EPP1.7] ..................................................................................................82 ECP Mode Use DMA [1] .................................................................................................
FPC 6065 / 6084 C. SAFETY PRECAUTIONS WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these precautions may result in permanent damage to the FPC6065/FPC6084. C.1 SAFETY PRECAUTIONS Please follow the safety precautions outlined in the sections that follow: C.1.1 General Safety Precautions Please ensure the following safety precautions are adhered to at all times. -Follow the electrostatic precautions outlined below whenever the FPC6065/FPC6084 is opened.
FPC 6065 / 6084 C.1.2 ANTI-STATIC PRECAUTIONS WARNING: Failure to take ESD precautions during the installation of the FPC6065/FPC6084 may result in permanent damage to the FPC6065/FPC6084 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the FPC6065/FPC6084. Dry climates are especially susceptible to ESD.
FPC 6065 / 6084 C.1.3 PRODUCT DISPOSAL CAUTION: Risk of explosion if battery is replaced by and incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations. Outside the European Union - If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.
FPC 6065 / 6084 -Turn the PPC-2706/PPC-2708 off before cleaning the FPC6065/FPC6084. -Never drop any objects or liquids through the openings of the FPC6065/FPC6084. -Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the FPC6065/FPC6084. -Avoid eating, drinking and smoking within vicinity of the FPC6065/FPC6084. C.2.2 Cleaning Tools Some components in the FPC6065/FPC6084 may only be cleaned using a product specifically designed for the purpose.
