MOUNTING GUIDE N O N - W AT E R P R O O F R I B B O N LY T E Complete Integrated LED Lighting Solutions Tech Support: 212.629.
M AT E R I A L L I S T I N S TA L L A - S I L I C O N E PA D S (A) (B) (C) (D) (E) Rubbing Alcohol (for metallic surfaces) Double Sided Tape Silicone Pad Screws RibbonLyte I N S TA L L B - Z I P T I E PA D S (A) (B) (C) (D) (E) Rubbing Alcohol (for metallic surfaces) Double Sided Tape Zip Tie Pad Zip Tie RibbonLyte PA G E 1 All artwork and images copyright Acolyte Industries Inc. Use or reprinting prohibited unless explicitly approved by Acolyte Industries.
I N S TA L L A - S I L I C O N E PA D S PREFERRED METHOD BET TER LOOKING I N S TA L L B - Z I P T I E PA D S A LT E R N AT E M E T H O D E A S I E R T O I N S TA L L PA G E 2 All artwork and images copyright Acolyte Industries Inc. Use or reprinting prohibited unless explicitly approved by Acolyte Industries.
A - M O U N T N O N - W AT E R P R O O F R I B B O N LY T E W I T H S I L I C O N E PA D S Clean the mountain surface free of dust and debris using a wet cloth. For metal mounting surfaces use rubbing alcohol (A) to wipe clean. 1 2 After surface is dry, apply 1/16” double-sided tape (B) to the desired mounting path of your RibbonLyte. If mounting to a wall, use a level to ensure a straight line. (B) (A) 3 Remove backing from double-sided tape (B).
I N S TA L L A - - S T E P S 5 - 8 5 Apply the RibbonLyte (E) by placing one end of the strip at the end of the doublesided tape (B) inside the channel then slide your finger along the RibbonLyte (E) to make sure there is firm contact and that the tape adheres well. 6 Every 12 inches place a silicone pad (C) over the RibbonLyte (E) and use a pencil to mark where each pilot hole will be drilled. DO NOT place the pad above an LED. Place it as close to 12 inches as possible, while not touching any LEDs.
I N S TA L L A - - C O M P L E T E 9 Your RibbonLyte installation is complete. PA G E 5 All artwork and images copyright Acolyte Industries Inc. Use or reprinting prohibited unless explicitly approved by Acolyte Industries.
B - M O U N T N O N - W AT E R P R O O F R I B B O N LY T E W I T H Z I P T I E PA D S Clean the mountain surface free of dust and debris using a wet cloth. For metal mounting surfaces use rubbing alcohol (A) to wipe clean. 1 2 After surface is dry, apply 1/16” double-sided tape (B) to the desired mounting path of your RibbonLyte. If mounting to a wall, use a level to ensure a straight line. (B) (A) 3 Remove backing from double-sided tape (B). 4 Take the backing off the zip tie pads (C).
I N S TA L L B - - S T E P S 5 - 8 5 Apply the zip tie pads (C) directly over the double-sided tape (B) on your mounting surface, approximately every 12 inches. 6 Drill a pilot hole through the center of each zip tie pad (C) into the mounting surface where they are positioned. 7 Screw the zip tie pad (C) into place with a size 8 counter sunk flat head screw. 8 Slide zip ties (D) through the openings in each of the zip tie pads (C) but do not connect the ends of the zip ties.
I N S TA L L B - - S T E P S 9 - 1 1 9 11 Apply the RibbonLyte (E) by placing one end of the strip at the end of the doublesided tape, then slide your finger along the RibbonLyte (E) to make sure there is firm contact and that the tape adheres well. The RibbonLyte (E) should go directly over the top of the zip tie pads (C). 10 Wrap the zip tie (D) around the RibbonLyte (E) and slide the tail of the tie through the other end until it holds its position and has a snug fit.
I N S TA L L B - - C O M P L E T E 12 Your RibbonLyte installation is complete. PA G E 9 All artwork and images copyright Acolyte Industries Inc. Use or reprinting prohibited unless explicitly approved by Acolyte Industries.
