AV100 B/C AM/FM RADIO WITH iPod DOCKING FEATURE Owner’s Manual
Congratulations Thank you for purchasing the Acoustic Research AV100 AM/FM Radio Receiver System with iPod compatibility. The B or C suffix after the model number indicates a black (B) or cherrywood (C) cabinet. Besides featuring standard AM and FM radio reception with dedicated antenna input connections, the AV100 also provides an iPod docking connector for listening to downloaded material from the internet when the iPod mode is selected.
FCC Information Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
AV100 System Components AV100 AM/FM Radio with iPod Docking Feature (iPod Not Included) Remote Control with Battery AM Antenna FM Antenna AC Line Power Cord 4 AV100
Installing and Setting Up the AV100 You can begin to enjoy your AV100 Radio system as soon as the installation is completed as follows: 1. Determine the desired area where the unit is to be installed; i.e., table top, stereo cabinet, etc. Note: If possible, the unit should be positioned near a window to achieve the best reception with the AM and FM antennae. 2. Make sure the line power rocker switch at the rear of the unit is in the off (O) position.
MODE Button Each time the MODE button is pressed, the operating status of the unit changes in sequence from AM through AUX 2; as the mode changes, the associated blue LED lights accordingly. When the AV100 is turned off, the last operating mode in effect at the time is re-established when the unit is again turned on.
Functions of Controls, Indicators and Connectors AV100 Radio System, Rear View 1 2 7 6 3 4 5 AV100 Radio System, Top View 18 8 9 17 10 16 11 15 14 13 12 AV100 Radio System, Front View 25 19 20 21 24 AV100 23 22 7
Functions of Controls, Indicators and Connectors (Cont) 1. POWER ON/OFF Rocker Switch: When pressed to the ON ( I ) position, AC input power is applied to the radio system, placing it in the standby mode. 2. AC IN Power Connector: 2-prong male power connector for power cable connection to 120V, 60Hz power. 3. SUB OUT Audio Connector: Female RCA audio output connector to external subwoofer speaker. 4.
AV100 Operation Preoperational Considerations Prior to operation, perform the following steps: 1. Remove the protective film from the battery compartment of the remote control. 2. Connect the power and antenna cables to the AV100 as outlined previously. 3. Apply line power to the AV100 by pressing the line power rocker switch on the rear of the unit to the on (I) position; the mode LEDs flash on for 2 seconds and then go out. The AV100 is now in the standby mode. 4.
Charging the iPod: The iPod’s battery is charged when the AV100 is switched on (independent of the input source selected). This charging function is not supported in the standby mode. Special AV100 iPod Features The AV100 iPod feature is compatible with the following models: iPod Video Nano-Classic 3rd generation 1GB 2GB 4GB NOT COMPATIBLE iPod-Classic 5th generation (color display) 20GB 30GB NOT COMPATIBLE The following iPod models are compatible via the AUX 1 input and an additional 3.
Specifications Frequency Range: AM (UL) FM (UL) 530kHz - 1710kHz 87.5MHz - 108MHz Power Amplifier: 2” x 3” magnetic shielded speaker, 10 W RMS @ 10% THD, Frequency Response: 80Hz - 20kHz 120 VAC 60Hz power supply 300 Ohm twin lead to connect the AM antenna 75 Ohm F-connector to connect the FM antenna RCA-type jack AUX 1 for external audio input source 3.
© 2007 Audiovox Electronics Corporation, 150 Marcus Blvd.
