900MHz WIRELESS STEREO SPEAKERS Model AW871 Installation and Operation Manual
Table of Contents I. II. III. IV. V. VI. VII. VIII. IX. Location of functions………..……………………………………………. Connecting the speaker system………..……………………………….. Adjusting the transmitter………..………………………………………. Tuning the speakers………..…………………………………………….. Turning the speakers off………..………………………………………... Recharging the batteries………..……………………………………….. More helpful information ………..……………………………………… Troubleshooting………..……………………………………………........ Specifications & Features ………..……………………………………… 2 3 5 6 7 7 7 9 10 X.
I. Location of Functions Speaker Front View: Speaker Back View: G B A E D F C C. Power/volume/scan control D. Battery compartment cover E. Speaker power input jack F. Left/mono/right switch G. Carrying handle Transmitter Front View: Transmitter Back View: A. Tuning indicator light (tuned) B. Standby/Charging indicator light (stdby/chrg) J K I H I. Transmitter power input jack J. Audio input cable K. Channel select switch H. Power indicator light Accessories: O.
Audio Output II. Connecting the Speaker System Audio Output I. Powering the Transmitter Connect the small, round plug from the transmitter AC power adapter (L) to the transmitter power input jack (I) and plug the other end of the transmitter Sortie audio AC power adapter (L) into any standard 120V AC wall outlet. Audio Output Note: Be sure to use the AC power adapter rated 12V DC 100 mA. Sortie audio Note: There is no transmitter ON/OFF switch.
Warning: This product is designed to work with line level outputs or headphone outputs only. DO NOT connect it directly to speaker outputs, as it will permanently damage the transmitter. III. Powering the Speakers There are two options to power your wireless speakers: i. AC Power Adapter: 1. Turn the speaker volume down by rotating the power/volume/scan control (C) on the front of the speaker all the way to the left. Speaker AC Power adapter (M) 3.
III. Adjusting the Transmitter J I K H H. Power indicator light I. Transmitter power input jack J. Audio input cable K. Channel select switch 1. Turn ON your audio source (i.e., A/V receiver, TV, stereo, etc.) and play music at a normal listening volume. 2. Set the channel select switch (K) on the back of the transmitter to 1, 2 or 3. The transmitter provides three different broadcasting frequencies.
IV. Tuning the Speakers B A F C A. Tuning indicator light (tuned) B. Standby/Charging indicator F. Left/mono/right switch light (stdby/chrg) C. Power/volume/scan control 1. Push the power/volume/scan controls (C) to turn each speaker ON. The standby/charging indicators (B) will illuminate red while the speakers are tuning to the transmitter.
V. Turning the Speakers Off 1. Push and hold the power/volume/scan control (C) to turn each speaker OFF. You will need to hold the control for about 1.5 seconds for the speaker to turn off. 2. Confirm that the speaker is off by verifying that the red “standby/charging” light and the blue “tuned” light are off.
Fixed-level outputs from TVs are usually marked as ‘Constant,’ ‘Fixed,’ or ‘Select.’ If they are not marked as such, they are probably variable outputs (see “About Variable-Level Audio Outputs” below). Outputs from VCRs are almost always fixed. Hint: When connecting to the audio outputs of a VCR, remember that the VCR must be playing a tape or showing a TV channel for sound to be produced.
VIII. Troubleshooting The following troubleshooting guide takes you through some of the more common problems associated with the installation and/or operation of a wireless system. If the problem persists, please call 1-800-732-6866 and a knowledgeable customer service representative will assist you.
IX. Specifications & Features Transmitter Omnidirectional Effective transmitting range: up to 300 feet* 3 selectable broadcast frequencies (between 912.5 and 914.5 MHz) Line audio input with 3.
X. Warranty 12 MONTH LIMITED WARRANTY Audiovox Electronics Corporation (the “Company”) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced (at the Company’s option) without charge for parts and repair labor.
