Owner’s Manual Contents Model Identification............................ 2 Important safety instructions.... 3 Precautions to avoid possible exposure to excessive microwave energy.................... 4 Heavy Duty Commercial Compact [0.6 Cubic Foot] Microwave Oven Keep these instructions for future reference. If the oven changes ownership, this manual must accompany oven. Grounding/Earthing Instructions......... 5 Installation.......................................... 6 Display and Features Style 1.....
Model Identification When contacting ACP, provide product information. Product information is located on oven serial plate. Record the following information: Any questions or to locate an authorized service agent contact ACP, Inc. ComServ Customer Service at: Phone 866.426.2621 / 319.368.8195 or email: commercialservice@acpsolutions.com. Warranty service must be performed by an authorized servicer. ACP also recommends contacting an authorized servicer if service is required after warranty expires.
IMPORTANT SAFETY INSTRUCTIONS Recognize this symbol as a SAFETY message ! WARNING When using electrical oven, basic safety precautions should be followed to reduce the risk of burns, electric shock, fire, or injury to persons or exposure to excessive microwave energy. 8. DO NOT operate this oven if it has a damaged cord or plug, if it is not working properly, or if it has been damaged or dropped. 1. READ all instructions before using oven. 2.
IMPORTANT SAFETY INSTRUCTIONS ! CAUTION To avoid personal injury or property damage, observe the following: 7. Do not use regular cooking thermometers in oven. Most cooking thermometers contain mercury and may cause an electrical arc, malfunction, or damage to oven. 1. Briskly stir or pour liquids before cooking with microwave energy to prevent spontaneous boiling or eruption. Do not overheat. If air is not mixed into a liquid, liquid can erupt in oven or after removal from oven. 8.
Grounding Instructions WARNING WARNING To avoid risk of electrical shock or death, this oven must be grounded. To avoid risk of electrical shock or death, this oven must be grounded. WARNING WARNING To avoid risk of electrical shock or death, do not alter the plug. To avoid risk of electrical shock or death, do not alter the plug. This oven MUST be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current.
Installation Unpacking Oven Oven Placement • Inspect oven for damage such as dents in door or dents inside oven cavity. • Report any dents or breakage to source of purchase immediately. Do not attempt to use oven if damaged. • Remove all materials from oven interior. • If oven has been stored in extremely cold area, wait a few hours before connecting power. • Do not install oven next to or above source of heat, such as pizza oven or deep fat fryer.
Display and Features NOTE: There are two styles of controls shown Style 1 and Style 2 choose the control that matches unit STYLE 1 TIME Entry pad is used to enter cooking time for either manual entry or programming. Cooking time ranges from 1 second (00:01) to a total of 60 minutes (60:00) over four stages. If more than 60 minutes of total microwave cooking time is required, open door and inspect food before beginning new cooking cycle.
Display and Features STYLE 1 Cooking Methods Manual Time Entry Manual Time Entry feature allows the operator to heat without changing the preprogrammed pads. Time must be entered and power can be set before cooking. START pad must be pressed to begin cooking. Memory Pads This oven can of store either 10 or 100 cooking programs in memory. Single Pad Cooking From the factory, it is programmed to store 10 cooking programs. Each pad begins a cooking program.
Operation STYLE 1 Interrupting Operation Double Pad Programs The oven control can be changed to store up to 100 cooking programs. See the “User’s Options” section of this manual to change oven control. Open oven door or press STOP/RESET pad to interrupt operation. Display continues to show countdown time. Close door and press START pad to resume oven operation. To start a double pad cooking program, press 2 memory pads. For example, press pad 0 and pad 3 to start a cooking program.
Programming STYLE 1 • After 5 seconds, signal sounds. Display shows “PROGRAM”. 3. Press 3 pad to select memory pad. • Display shows cooking time, “STAGE 1” and power level if other than 100 percent power. 4. Press 3 and 0 pad to enter desired cooking time. 5. Press POWER LEVEL pad to change power level. • Display shows cooking time and current power level if other than 100 percent power. 6. Press 8 pad to enter desired power level. Note: Press POWER LEVEL twice to reset to 100% power. 7.
Options STYLE 1 User Options Follow the instructions below to customized the microwave oven’s operation. End-of-cycle signal, maximum cooking time and other options can be changed to meeting your cooking needs. Example: Change setting to single digit pad operation. 1. Open oven door. • If door is closed or STOP/ RESET pad is pressed before finishing programming sequence, oven exits programming mode. 2. Press and hold pad 2 for approximately 5 seconds. • After 5 seconds, signal sounds.
Display and Features STYLE 2 Single Pad Programming Start Pad The start pad is used to begin a manual time entry cooking cycle. It is also used to save any changes to programming sequences or user options. STOP/RESET pad The STOP/RESET pad stops a cooking sequence in progress, clears out any remaining time, and also ends a programming or user option cycle. When the STOP/RESET pad is used to end a programming or option change, the changes are discarded.
Operation STYLE 2 Cooking Display dISPLAYS dESCRIPTION READY READY displays when oven control will accept entries. 00:00 Displays cooking time. If stage cooking is programmed, total cooking time is displayed. COOK LEVEL COOK LEVEL displays while oven is operating. The cooking level is displayed above as a number 1 through 9. If no number is displayed, the oven is cooking at full power. POWER is displayed while the oven is generating microwave energy during a cooking cycle.
Operation STYLE 2 Interrupting Operation Open oven door or press STOP/RESET pad to interrupt operation. Display continues to show countdown time. Close door and press START pad to resume oven operation. Canceling Mistakes • • • If oven is not cooking, press STOP/RESET pad to clear display. If oven is cooking, press STOP/RESET pad once to stop oven, then again to clear display. If oven door is open and time shows in display, close oven door and press STOP/RESET pad to clear display.
Programming STYLE 2 Programming Pads Oven is shipped from the factory for single pad programming. To change the oven default to allow double pad programming, see User Options. To change the amount of time or the power level for a preset pad: 1. Open oven door. • READY displays. • If door is closed or RESET pad is pressed before programming is complete, changes are discarded and microwave exits programming mode. 2. Press and hold pad 1 for approximately 5 seconds. • This begins programming mode.
Options STYLE 2 Didn’t like an option? Factory settings are marked in bold. To change the oven back to the factory setting, simply select the option that is marked in bold. My changes weren’t saved. In order for any changes to be saved, the START pad must be pressed after selecting an option.
Care and Cleaning ! WARNING To avoid electrical shock which can cause severe personal injury or death, unplug power cord or open circuit breaker to oven before cleaning or removing light bulb. Part Description Interior, Exterior, and Door Clean microwave oven with mild detergent in warm water using soft sponge or cloth. Wring sponge or cloth to remove excess water before wiping equipment. If desired, boil a cup of water in microwave oven to loosen soil before cleaning.
Part Description A ir I nta k e F ilte r F ilte r is loc a te d be low ove n door. C le a n a ir inta k e filte r we e k ly for prope r airflow. Wash filter in hot water and mild detergent. Do not use oven without filter in place. Remove filter to clean. Important To avoid overheating and oven damage, clean air filter regularly. 1. Grasp filter tab and pull forward. Filter will release from retaining clips. 2. To reinstall, place bottom of filter in clips and push top of filter into position.
Before Calling for Service Record all inspections and repair for future reference. ! WARNING To avoid electrical shock which can cause severe personal injury or death, do not remove outer case at any time. Only an authorized servicer should remove outer case. Symptom Check I f oven does not operate: • Check fuse or circuit breaker. • Confirm oven is plugged into dedicated circuit. If oven does not accept entries when pad is pressed: • Confirm oven is on grounded and polarized circuit.