User Guide
Table Of Contents
- Chapter 1. Introduction
- Chapter 2. Acronis True Image Enterprise Server installatio
- Chapter 3. General information and proprietary Acronis tech
- 3.1 The difference between file archives and disk/partition
- 3.2 Full, incremental and differential backups
- 3.3 Acronis Secure Zone
- 3.4 Acronis Startup Recovery Manager
- 3.5 Acronis Backup Server
- 3.6 Acronis Snap Restore
- 3.7 Acronis Universal Restore
- 3.8 Using dynamic disks and volumes
- 3.9 Backing up to tape drive
- 3.10 Viewing disk and partition information
- Chapter 4. Using Acronis True Image Management Console
- Chapter 5. Using Acronis True Image Enterprise Server (loca
- Chapter 6. Creating backup archives
- Chapter 7. Restoring the backup data
- 7.1 Restore under Windows or boot from CD?
- 7.2 Restoring files and folders from file archives
- 7.3 Restoring disks/partitions or files from images
- 7.3.1 Starting the Restore Data Wizard
- 7.3.2 Archive selection
- 7.3.3 Restoration type selection
- 7.3.4 Selecting a disk/partition to restore
- 7.3.5 Selecting a target disk/partition
- 7.3.6 Changing the restored partition type
- 7.3.7 Changing the restored partition file system
- 7.3.8 Changing the restored partition size and location
- 7.3.9 Assigning a letter to the restored partition
- 7.3.10 Restoring several disks or partitions at once
- 7.3.11 Using Acronis Universal Restore
- 7.3.12 Setting restore options
- 7.3.13 Restoration summary and executing restoration
- 7.4 Setting restore options
- Chapter 8. Scheduling tasks
- Chapter 9. Managing Acronis Secure Zone
- Chapter 10. Creating bootable media
- Chapter 11. Other operations
- Chapter 12. Mounting an image as a virtual drive
- Chapter 13. Transferring the system to a new disk
- 13.1 General information
- 13.2 Security
- 13.3 Executing transfers
- 13.3.1 Selecting Clone mode
- 13.3.2 Selecting source disk
- 13.3.3 Selecting destination disk
- 13.3.4 Partitioned destination disk
- 13.3.5 Old and new disk partition layout
- 13.3.6 Old disk data
- 13.3.7 Destroying the old disk data
- 13.3.8 Selecting partition transfer method
- 13.3.9 Partitioning the old disk
- 13.3.10 Old and new disk partition layouts
- 13.3.11 Cloning summary
- 13.4 Cloning with manual partitioning
- Chapter 14. Adding a new hard disk
- Chapter 15. Command-line mode and scripting
Specifies the partition where the image file is stored (by letter or number). This option is
used with /filename:file_name. In this case the file name must be specified without drive
letter or root folder. For example:
/file_partition:D /filename:"\1.tib”
/password:[password]
Specifies the password for the image file (if required).
/harddisk:[disk number]
Specifies the hard disks to restore by numbers.
/partition:[partition number]
Specifies the partitions to restore by numbers.
/target_harddisk:[disk number]
Specifies the hard disk number where the image will be restored.
/ur_path:[path] /ur_username:[user] /ur_password:[pwd]
Specifies using Acronis Universal Restore and the path to the drivers storage.
/ur_driver:[inf-filename]
Specifies using Acronis Universal Restore and the mass-storage driver to be installed.
Acronis Universal Restore is an add-on to Acronis True Image Enterprise Server. It is
purchased separately and installed from a separate setup file. The above two options are for
Acronis True Image Enterprise Server installations including Acronis Universal Restore. For
more information see
3.7 Acronis Universal Restore
and
7.3.11 Using Acronis Universal
Res ore
.
t
/start:[start sector]
Sets the start sector for restoring a partition to the hard disk unallocated space.
/size:[partition size in sectors]
Sets the new partition size (in sectors).
/type:[active | primary | logical]
Sets the new partition type. By default (if this option is not defined) an active partition is
created on the first hard disk and logic partitions on other disks.
/target_partition:[partition number]
Specifies the target partition number for restoring a partition over the existing one. If the
option is not specified, the program assumes that the target partition number is the same as
the partition number specified with the /partition option.
/reboot
Reboots the server after the operation is completed.
/log:[file name]
Creates a log file of the current operation with the specified file name.
3. list
Displays the list of the available drives and partitions.
Copyright © Acronis, Inc., 2000-2006 105