Operation Manual Operation Manual Nimbie USB Plus Disc Autoloader Model #: NB21 Series (PC-Connected) Serial Number: ______________________________ (The serial number is labeled on the bottom of the device.
Operation Manual, Nimbie USB Plus Version 1.2 PREFACE Important Safety Instructions For your safety, basic precautions should always be followed to reduce risk of damage, electric shock, fire, and personal injury. This includes the following: Read this manual carefully and follow all warnings and instructions. Operate the unit with only the proper electrical specifications as labeled on the device.
Version 1.2 Operation Manual, Nimbie USB Plus FCC Compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Operation Manual, Nimbie USB Plus Version 1.2 device not provided with the product, or if the serial number label provided with this product has been broken or removed. This warranty does not cover damages that occur in shipment, due to acts of God. All repairs and replacement services shall only be handled by Acronova Technology Inc, and by authorized service centers. Parts used for replacement are covered only for the remainder of the warranty period. Acronova Technology Inc.
Version 1.2 Operation Manual, Nimbie USB Plus Table of Contents Preface................................................................................................2 Specifications....................................................................................6 Unpacking Your Package..................................................................7 Package Contents..........................................................................7 Getting Familiar with the device...........................
Operation Manual, Nimbie USB Plus Version 1.2 SPECIFICATIONS Disc Recorder Input Capacity: One Blu-ray/CD/DVD recorder 30 discs; 100 discs using extension rods (increased capacity using non-stop refill) Output Capacity: Dependent capacity (finished discs are placed in front of the unit, in a separate container, or Disc Storage Bin) Reject Disc Capacity: 5 discs without legs; 30 discs using legs Write Speed: BD-R: DVD±R: CD-R: Interface: USB 3.0 SuperSpeed (backward compatible with USB 2.
Version 1.2 Operation Manual, Nimbie USB Plus UNPACKING YOUR PACKAGE Congratulations on purchasing the Nimbie USB Plus Disc Autoloader. Nimbie USB Plus is a state-of-the-art integrated system, with a built-in single optical disc recorder, USB 3.0 interface and autoloader, which requires a PC and software to operate. Nimbie USB Plus has a 30 disc capacity and an enclosure that protects discs from dust.
Operation Manual, Nimbie USB Plus Version 1.2 One Nimbie USB Plus Disc Autoloader One Power Cord One Power Adapter One USB 3.0 Cord (backward compatible with USB 2.0) One Spindle Box (serves as the Finish Disc Bin) Three Extension Rods (attached to the underside of Nimbie USB Plus' lid) One Alignment Pad Four Legs One Installation Disc (includes device driver and software) One Operation Manual Two Software Manuals *To use Nimbie USB Plus at its MAXIMUM speed, a USB 3.
Version 1.2 Operation Manual, Nimbie USB Plus GETTING FAMILIAR WITH THE DEVICE A Look at Nimbie USB Plus Lid (Blank Disc Storage) Open the lid to access the blank disc storage area. Control Panel Located on the top front of Nimbie USB Plus, the control panel contains the LED indicators. Legs Use the four legs included with your Nimbie USB Plus to provide space underneath for rejected discs.
Operation Manual, Nimbie USB Plus Version 1.2 Vent This allows heat to escape. Do not block this otherwise the unit may overheat. Rear View Power Switch Turn Nimbie USB Plus on and off. Power Socket Use the provided power cord to connect Nimbie USB Plus to a wall outlet. USB 3.0 Port Connects Nimbie USB Plus to the host PC (required for USB 3.0 speeds or backward compatible with USB 2.0 at USB 2.0 transfer speeds). Kensington Security Slot Security lock anti-theft system.
Version 1.2 E z z z z z z z L { { { { z z z { { U z { { z z z z z { z Operation Manual, Nimbie USB Plus R Description Initialization in progress... { USB 3.0/SuperSpeed connection established (discs in loader) USB 3.0/SuperSpeed connection established (disc-loader empty) { USB 2.0/Hi-speed connection established (discs in loader) USB 2.
Operation Manual, Nimbie USB Plus Version 1.2 INSTALLATION Finding a Place for Nimbie USB Plus Nimbie USB Plus should be placed on a fairly level surface, firm enough to support the unit and discs. Always allow ample workspace for your operation, with easy access to the blank and finished discs. Do not expose the unit to direct sunlight or high humidity, as it may cause the unit to malfunction.
Version 1.2 Operation Manual, Nimbie USB Plus Nimbie USB Plus Installation Follow the steps below to complete Nimbie USB Plus’s hardware installation: 1) Place Nimbie USB Plus on level surface so that it stands firmly on its legs. 2) Place the spindle box that came with the unit in front of Nimbie USB Plus. Use the alignment pad to appropriately position the spindle box under the Finish Disc Slot.
Operation Manual, Nimbie USB Plus Version 1.2 6) Wait patiently until the initialization is complete. You may now proceed to install the application software. Note: Mac system will install the driver automatically after install the QQGetTray software . Application Software Installation Nimbie USB Plus application software is included in the installation disc. Follow the steps below to complete the installation: 1) Insert the installation disc into an available optical drive on PC.
Version 1.2 Operation Manual, Nimbie USB Plus BEFORE GETTING STARTED Handling Optical Discs Never touch the printable or data surface of the discs, as it may decrease disc quality and lifespan. Always handle discs from the outer edge or the center hole. Loading Discs to Nimbie USB Plus Load one disc into the disc loader first and assure it is firmly resting on the three wheels in the illustration to the right.
Operation Manual, Nimbie USB Plus Version 1.2 Rejected Discs Nimbie USB Plus is designed to have Rejected Discs come out underneath the unit. Do not block the Reject Disc Slot. Periodically remove rejected discs so that there is room to accommodate more discs or raise Nimbie USB Plus using the provided legs to increase space underneath for more discs. Important: Nimbie USB Plus will stop operation if rejected discs cannot go through the Reject Disc Slot.
Version 1.2 Operation Manual, Nimbie USB Plus Disc Bin may be a spindle box or a container with enough depth to accommodate 100 discs in a session. Since Nimbie USB Plus is equipped with a FIFO (First-In-First-Out) disc loader, you may simply refill discs before the disc loader becomes empty. This will allow an unlimited number of additional discs to be processed in one session, as long as the Finish Disc Bin is continually emptied.
Operation Manual, Nimbie USB Plus Version 1.2 Disc Separation Certain blank discs may tend to stick to each other or may be difficult to separate. Avoid using these types of discs. Nimbie USB Plus is equipped with a patent pending disc separator, which handles discs that adhere to each other better than traditional autoloaders. However, it is strongly recommended that you separate or loosen blank discs from each other before use. 18 © 2012, Acronova Technology, Inc.
Version 1.2 Operation Manual, Nimbie USB Plus OPERATION QUICK GUIDE Follow the steps below to get your Nimbie USB Plus ready. Turning Nimbie USB Plus On 1) Connect the power cord to Nimbie USB Plus and a wall outlet. 2) Turn on the host computer, which is connected to Nimbie USB Plus via USB 3.0 port. 3) Connect USB 3.0 cable to both Nimbie USB Plus and your PC. 4) Turn Nimbie USB Plus’s power switch to the On position.
Operation Manual, Nimbie USB Plus Version 1.2 Start QQGetTray for Mac QQGetTray is a software utility enables autoloader to automatically load and unload discs with other 3rd party software applications. Many software applications are capable of processing disc burning or ripping jobs automatically after a disc is loaded to a CD/DVD drive and will eject the drive tray when the job is finished.
Version 1.2 Operation Manual, Nimbie USB Plus There are 4 buttons in the main menu: • START Click this button to start QQGetTray, Nimbie USB Plus will begin to monitor the disc tray and change discs automatically. The “START” button will change to “STOP” after activation. • START and LOAD Click this button to start QQGetTray, Nimbie USB Plus will load a disc into it's CD/DVD drive, then begin monitoring the disc tray and change discs automatically.
Operation Manual, Nimbie USB Plus Version 1.2 FREQUENTLY ASKED QUESTIONS What should I do when software can not detect the autoloader? Make sure the disc autoloader is connected to PC via USB 3.0 or USB 2.0 and the power is on. Make sure the autoloader's LED display is on “Ready” status. Make sure the disc autoloader's driver is installed properly. Refer to the “Software Installation” section on how to install the driver. Try another USB slot on PC and check the connection.
Version 1.2 Operation Manual, Nimbie USB Plus APPENDIX A: TIPS Nimbie USB Plus Maintenance Periodically cleaning the device will ensure proper performance. Follow the steps below to maintain Nimbie USB Plus: 1) 2) 3) 4) 5) Turn the power switch to the Off position. Remove the master and blank discs. Unplug the power cord from the wall outlet. Clean Nimbie USB Plus using a lint-free cloth moistened with warm water. Dry the unit immediately with a dry lint-free cloth.
Operation Manual, Nimbie USB Plus Version 1.2 Writing Speed The recorder will automatically adjust the writing speed according to the disc quality. The system will monitor and automatically adjust the writing speed as the optical laser moves from the inner ring to the outer ring, up to the selected speed. The recorder’s maximum speed may never be reached if a lower grade disc is used. At the maximum speed, for a single recorder, duplicating a 4.7 GB DVD should not take more than 8 minutes.
Version 1.2 Operation Manual, Nimbie USB Plus APPENDIX B: WORKING WITH IMGBURN How to get Nimbie USB Plus working with ImgBurn 1. Connect Nimbie USB Plus to PC and switch it on. 2. Download and install ImgBurn burning software. Go to ImgBurn website – http://www.imgburn.com/ 3. Copy files BSRobot20.dll & winusb.dll from installation disc \ImgBurn\ folder to where you installed ImgBurn (i.e. C:\Program Files\ImgBurn) in the same folder as ImgBurn.exe. 4. Launch ImgBurn burning software. 5.
Operation Manual, Nimbie USB Plus Version 1.2 7. ImgBurn will start detecting Nimbie USB Plus now. 8. If the autoloader detection did not start automatically, you can close ImgBurn and run it again, it will automatically detect the Nimbie USB Plus. 9. Now you can use ImgBurn with Nimbie USB Plus to unload discs after burnt, and load the next blank disc automatically. Reminder: Please pick up the RW that provided by Nimbie USB Plus as the destination in ImgBurn. 26 © 2012, Acronova Technology, Inc.
Version 1.2 Operation Manual, Nimbie USB Plus How to check Nimbie USB Plus in ImgBurn 1. There is an “Auto Loader Control” function in ImgBurn and you can use it to test the Nimbie USB Plus. 2. You can click the “Tool” menu, and select “Changer” > “Auto Loader Control” to launch it. © 2012, Acronova Technology, Inc.
Operation Manual, Nimbie USB Plus Version 1.2 Acronova Technology, Inc. http://www.acronova.com Manual Ver.: 1.2, February 2012 Part #: 711-NT21-9AC6-1 28 © 2012, Acronova Technology, Inc.
