HP-3000/4000 Terminal User’s Guide
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the Installation Manual, may cause harmful interference to radio communications.
Table of Contents Introduction Biometrics Principle of Operation Specifications Planning an Installation Site Preparation HandPunch Placement Wiring Power Input Battery Backup Earth Ground and Shielding Communications External Devices 3 4 4 7 11 11 11 12 12 12 13 18 20 Mechanical Installation 23 Networking and Communications 27 Wiring Connections 31 Erasing the Memory 43 Closing the HandPunch 45 Enter Command Menu 47 Wall Plate Installation Mounting the Wall Plate Stand-alone HandReader Ma
Appendix B - Differences in Board Layout 72 Appendix C - Old Installation Guide 76 Appendix D - Troubleshooting 94 Glossary 96 Limited Warranty 98
HandPunch 3000/4000 Manual Introduction The HandPunch 3000/4000 is part of Schlage Biometrics’ 3rd generation line of biometric hand geometry Time and Attendance Terminals1. The HandPunch records and stores a three-dimensional shape of the human hand for comparison and identity verification. Upon verification, the HandPunch records the time, date, user ID number, and collected time and attendance data for collection by a host computer.
Introduction Biometrics Biometrics is a term describing the automatic measurement and comparison of human characteristics. While its origins are ancient, the evolution of advanced scanning and microprocessor technology brought biometrics into everyday life. Electronic hand geometry technology first appeared in the 1970s. Schlage Biometrics Inc., founded in 1986, built the first mass-produced hand geometry readers and made biometric technology affordable for the commercial market.
HandPunch 3000/4000 Manual Four different features assist the user with hand placement and read verification. 1. 2. 3. 4. A light emitting diode (LED) hand placement display on the HandPunch’s top panel assists users with hand placement on the platen. A liquid crystal display (LCD) shows operational data and programming menus. “Red light/Green light” verification LEDs quickly inform users if their verification attempts were rejected or accepted.
Introduction HAND PLACEMENT DISPLAY VERIFICATION LIGHTS LCD DISPLAY Recog nition NUMERICAL KEYPAD 1 4 7 * No 8 0 2 5 9 s Inc.
HandPunch 3000/4000 Manual Specifications Table 1: Specifications Size: 8.85 inches wide by 11.65 inches high by 8.55 inches deep. 223 cm wide by 29.6 cm high by 21.7 cm deep. Power: 12 to 24 VDC or 12 to 24 VAC 50-60 Hz, 7 watts Weight: 6 lbs (2.7 kg) – 7 lbs (3.
Introduction Table 1: Specifications Time Schedules: Auxiliary Inputs: Auxiliary Outputs: Options HP-4000 – 3 definable time schedules per user 2 (open collector, 5 VDC present, sinks to ground, 100 mA max) up to 3 user definable (open collector, 5 VDC present, sinks to ground, 100 mA max) HandPunch units have the following options available. • • • Backup Battery Support See Technical Note 70200-0012 – Rev. D Modem Communication See Technical Note 70200-0013 – Rev.
HandPunch 3000/4000 Manual UL Compliance The HP-3000 and HP-4000 meet UL compliance requirements for UL 294 Access Control Systems under this condition: 1. The HandPunch is configured at the factory with a Wiegand output that enables the HandPunch to communicate with an access control panel. The access control panel controls the locking and unlocking of the door. The panel must reside on the secure side of the facility.
Introduction This page is intentionally blank.
HandPunch 3000/4000 Manual Planning an Installation Site Before you begin installation, check the site blueprints, riser diagrams, and Preparation specifications for important information about the HandPunch’s location and other systems that will connect to the HandPunch. Look for any existing wall preparations and wiring that other contractors may have installed for the HandPunch. A wire routing layout diagram (see “Figure 3-2” on page 25) is provided to assist in planning.
Planning An Installation Wiring Four basic circuits typically connect to the HandPunch: • • • • Power Input Earth Ground and Shielding Networking and Communications External Devices The minimum wire size for these circuits is AWG 22; the maximum wire size is AWG 18. Schlage Biometrics recommends using Belden 82732 or its equivalent when wiring for RS-422 communications. Power Input The HandPunch uses an internal switching regulator to obtain internal operational power.
HandPunch 3000/4000 Manual When input power is restored, the HandPunch switches off of battery operation and the battery charger is re-enabled to recharge the battery. Battery charge voltage is set at approximately 13.65 volts, and battery charge current is limited to approximately 50 mA. A fully discharged battery requires approximately 12 hours of charge to fully recover.
Planning An Installation This is an extremely important and often overlooked aspect of hard-wired serial communication systems. If the sending and receiving stations do not agree on the ground reference for the signal voltages, communication errors or a total inability to communicate may be observed. If the voltages are very different, it is even possible to damage the units.
HandPunch 3000/4000 Manual There are two standard methods for providing earth grounding to HandPunch units: • • earth grounding all units (see Figure 2-3) carrying an earth ground to each unit (see Figure 2-4) Earth ground all units when there is a good earth ground source near each unit and/or when there are very long cable runs between units. Carry an earth ground to each unit when there are no earth grounds Earth Ground convenient to the unit and the unit’s power supply is floating.
Planning An Installation GND T+ Remote 2 Remote 1 Master T- GND R+ GND R- R+ R- Connect the Cable Shield to Remote 1's Ground Connect the Cable Shield to Remote 2's Ground To Next Remote Connect the Cable Shield to the Master's Ground Do Not Connect the Cable Shield at this End Do Not Connect the Cable Shield at this End Do Not Connect the Cable Shield at this End Figure 2-3: Communication Shielding with All Units Earth Grounded All units are connected to the same earth ground.
HandPunch 3000/4000 Manual elevator motors or other large-current drawing machines) will have no effect on the communication network if this configuration is used. However, the power supplies must be truly floating, with no hidden paths back to the high-voltage side of the transformers, or to earth ground.
Planning An Installation Communications HandPunch to Host Computer Connection HandPunch/host computer communications can be configured in one of three ways: • • • • RS-232 Host Computer Connection NOTE RS-422 Host Computer Connection via a direct RS-232 connection via a direct RS-422 connection using a data converter via an optional Ethernet network connection (one HandPunch terminal must have the Ethernet communication option installed) via an optional Modem connection (one HandPunch terminal must ha
HandPunch 3000/4000 Manual NOTE Hand Punch When wiring the RS-422 daisy-chain network, do not wire HandPunch terminals in a “star” network (a network where a number of units are all connected to the network at one, central location – see Figure 2-5).
Planning An Installation connection is found on page 40. External Devices The HandPunch can control external devices such as: • • • • • • Bell Door Lock Request to Exit, Door Switch, and Auxiliary Inputs Auxiliary Outputs External Card Reader Serial Printer The HandPunch requires the use of an external DC power supply to operate other controls or relays. The power supply can be of a different voltage than that used to power the HandPunch.
HandPunch 3000/4000 Manual Request to Exit, Door Switch, and Auxiliary Inputs The HandPunch terminal has four inputs. Refer to the Inputs Wiring Diagram on page 36. • • • Request to Exit Door Switch Two Auxiliary Inputs A Request to Exit switch (REX) on the secure side of a controlled door will activate the lock output. When the REX switch is pressed, the door unlocks for a specified time. The REX switch must be a momentary contact, normally open switch rated greater than 0.5 mA, 5 VDC circuit.
Planning An Installation This page is intentionally blank.
HandPunch 3000/4000 Manual Mechanical Installation Select an installation location based on the guidelines provided in the Planning an Installation section beginning on page 11. Wall Plate Installation NOTE For the following instructions protect the HandPunch from the dust and debris generated during the wall plate installation process. 1. Remove the wall plate from the packing carton. Refer to Figure 3-1 for all wall plate references in the following section.
Networking and Communications 5. 6. 7. 8. 9. 10. Align a bubble level with the top edge of the wall plate and gently rotate the wall plate until the bubble level shows that the totp edge of the wall plate is level. Secure the plate to the wall using heavy masking tape. Using the wall plate as a template, mark the locations of teh two upper screw holes and the three lower screw holes. For a concealed wiring connection, trace the outline of the open area in the center of the wall plate.
HandPunch 3000/4000 Manual WIRE ENTRY POINT FOR RJ-11 JUNCTION BOX Wall Plate SURFACE CONDUIT ENTRY POINT CL 1.25" (3 cm) 50" Reference (127 cm) to Top of Wall Plate WIRE ENTRY POINT FOR SURFACE RJ-11 BOX 2" (5 cm) CL HandPunch 42.75" (108.6 cm) 42.5" (108 cm) 40.75" (103 cm) Finished Floor Figure 3-2: HandPunch Wire Routing Layout Attaching the 1. Remove the HandPunch from its carton. 2.
Networking and Communications HOLE 2 UPPER SCREWS SURFACE CONDUIT ENTRY KEYHOLE HOLES 3 LOWER MOUNTING SCREWS REAR OF TERMINAL : Attaching the HandPunch to the Wall Plate 3. 26 The Hand Punch is now ready for its wiring connections.
HandPunch 3000/4000 Manual Networking and Communications HandReader networking and communications can be configured in one of five ways: • • • • • as a stand-alone HandReader as a master or remote HandReader in a HandReader network as a remote HandReader in a HandReader network connected to a host PC as a remote network connected via optional Modem to host PC as a remote network connected via optional Ethernet to host PC Stand-alone HandReader When installed as a stand-alone access control system there
Networking and Communications • • • • • An unlimited number of sites can be created with up to 32 HandReaders per site. The HandReaders report all transactions to the PC. The HandNet software records all transactions and displays a variety of reports generated from this information. Template management is handled automatically. Users may enroll at any HandReader in the system. The PC collects the data and distributes it to other HandReaders in the network.
HandPunch 3000/4000 Manual Remote HandReader Connected to a Host PC via Optional Ethernet Printer The HandReader is available with an optional internal Ethernet communications module for TCP/IP communications. The wiring must conform to 10BaseT standards. Typically, network wiring terminates at the HandReader with a standard RJ-45 modular jack. The cable from the jack to the HandReader is not provided with the Ethernet option.
Networking and Communications This page is intentionally blank.
HandPunch 3000/4000 Manual Wiring Connections Once the HandPunch is attached to the wall plate the wiring connections to the HandPunch can be made (see Figure 4-1). WALL Power Connectors Reset Switch J7 Battery Jumper Wall Plate Terminal RJ-11 Strips Optional Modem Serial RS-232 or Ethernet RS-422 Top of Terminal Top of HandPunch Figure 4-1: Wiring Connections Wiring Examples The following tables provide the pinouts for the terminal strips on the HandPunch.
Wiring Connections The following figures provide typical HandPunch wiring diagrams. • • • • • • • • “Figure 4-4” on page 34 provides a typical Bell Output wiring diagram. “Figure 4-5” on page 35 provides a typical Lock Output wiring diagram. “Figure 4-6” on page 36 provides a typical Input wiring diagram. “Figure 4-7” on page 37 provides a typical Card Reader Emulation Mode wiring diagram. “Figure 4-8” on page 38 provides a typical Host PC Network System wiring diagram.
HandPunch 3000/4000 Manual Table 3: TS-2 - Output Connections Terminal 8 Connection Auxiliary Output 2 Table 4: RS-232 Connection Pin Signal Connection 1 GND Ground 2 RXD Receive Data Input (from external device) 3 TXD Transmit Data Output (to external device) 4 RTS Ready to Send Output (to external device) Table 5: RJ-11/RS-422 Network Connection J3 Pin Signal 1 Rx+ 2 Rx- 3 Tx- 4 Tx+ J3 Pins 1 2 3 4 Figure 4-2: J3 - RJ-11/RS-422 Jack Pinout 33
Wiring Connections RS-232 Pins 1 2 3 4 Figure 4-3: J4 - RS-232 Jack Pinout * POWER SUPPLY +12 to 24 VDC Max + NC NO *AUX RELAY BELL + - WALL TO WHICH THE HANDREADER IS ATTACHED HINGE 12 to 24 V AC/DC Input 1 14 13 12 11 10 9 2 8 7 6 5 4 3 2 1 RJ-11 RS-422 Connection TOP OF THE HANDREADER * These components are not supplied by Recognition Systems, Inc. ** The operation of the Auxiliary Outputs depend upon how the inputs have been configured.
HandPunch 3000/4000 Manual * POWER SUPPLY +12 to 24 VDC Max + NC *ELECTRIC LOCK + OR STRIKE - NO *LOCK RELAY WALL TO WHICH THE HANDREADER IS ATTACHED HINGE 12 to 24 V AC/DC Input 1 14 13 12 11 10 9 2 8 7 6 5 4 3 2 1 RJ-11 RS-422 Connection TOP OF THE HANDREADER * These components are not supplied by Recognition Systems, Inc. ** The operation of the Auxiliary Outputs depend upon how the inputs have been configured.
N.C. DOOR SWITCH* REQUEST TO EXIT N.O. MOMENTARY* AUX INPUT 1** N.O. DOOR SWITCH SWITCH LEGEND AUX INPUT 2** Wiring Connections WALL TO WHICH THE HANDREADER IS ATTACHED HINGE 12 to 24 V AC/DC Input 1 14 13 12 11 10 9 2 8 7 6 5 4 3 2 1 RJ-11 RS-422 Connection TOP OF THE HANDREADER * These components are not supplied by Recognition Systems, Inc. ** The operation of the Auxiliary Inputs depend upon how the inputs have been configured.
HandPunch 3000/4000 Manual Card Reader GROUND DATA 1 DATA 0 +5 VDC POWER (SEE NOTE BELOW) Access Panel GROUND DATA 1 DATA 0 WALL TO WHICH THE HANDREADER IS ATTACHED HINGE 12 to 24 V AC/DC Input 1 14 13 12 11 10 9 2 8 7 6 5 4 3 2 1 RJ-11 RS-422 Connection TOP OF THE HANDREADER NOTE: For +12 VDC readers, connect power supply +12 VDC to card reader.
Wiring Connections DC-102 RS-232 to 4-wire RS-422 Power Supply Data Converter (P/N DC-102) B DB-25 Serial Port Recogniti on 1 2 4 5 7 8 * No 0 3 6 9 * RS-422 4-Wire (2 Twisted Pairs) Inc. Clear F1 Enter HandPunch 1 Recogniti on 4 7 * No 2 5 8 3 6 9 0 Systems * RS-422 4-Wire (2 Twisted Pairs) Inc. Clear Enter Recogniti on 1 7 0 2 5 8 3 6 9 Systems G Y J-3 * RS-422 4-Wire (2 Twisted Pairs) Inc.
HandPunch 3000/4000 Manual RSI Supplied Cable (Black) Recogniti on 1 4 7 * No 8 0 2 5 9 Systems Inc. Clear F1 F2 # No Yes 3 6 Enter Modem Unit HandPunch Modem Port RJ-11 Telephone Outlet HandPunch RS-422 RJ-11 Port B R G Y * RS-422 4-Wire (2 Twisted Pairs) RJ-11 Jack Surface or Wall Plate Recogniti on 1 2 4 5 7 8 * No 0 3 6 9 Inc.
Wiring Connections Ethernet Cable Recogniti on 1 4 7 * No 2 5 8 0 3 6 9 Connection to Host Computer via Ethernet HandPunch Ethernet Port Inc. Clear F1 F2 # No Yes Systems Enter HandPunch RS-422 RJ-11 Port Ethernet Unit B R G Y * RS-422 4-Wire (2 Twisted Pairs) RJ-11 Jack Surface or Wall Plate Recogniti on 1 2 4 5 7 8 * No 0 3 6 9 Inc.
HandPunch 3000/4000 Manual *Host Computer/Hyperterminal *Serial Printer WALL TO WHICH THE HANDREADER IS ATTACHED HINGE HINGE 12 to 24 V AC/DC Input 1 4 Pin Connector 14 13 12 11 10 9 2 RJ-11 RS-422 Connection 8 7 6 5 4 3 2 1 J4 RS-232 Jack TOP OF THE HANDREADER * These components are not supplied by Recognition Systems, Inc.
Wiring Connections This page is intentionally blank.
HandPunch 3000/4000 Manual Erasing the Memory There are two options when erasing the memory of the HandReader: 1. 2. Setup All The erasing of the setup will set the HandReader’s address, passwords, etc., back to factory defaults. Erasing HandReader Memory Choosing the All option will take the HandReader’s setup back to factory defaults plus erase all user databases and datalogs. This action cannot be undone.
Planning an Installation This page intentionally blank.
HandPunch 3000/4000 Manual Closing the HandPunch Before closing the HandPunch clear all dust and debris away from the HandPunch. With the wal mount latch in the unlocked position, swing the body of the HandPunch up and lock the latch into place with the key provided with the HandPunch (see Figure 6-1 below). Dust and debris surrounding the HandPunch can drastically affect the terminal’s operation. It is important to ensure the HandPunch is free from dust and debris before closing the terminal.
Planning an Installation This page intentionally blank.
HandPunch 3000/4000 Manual Enter Command Menu Press the CLEAR and ENTER keys simultaneously to enter a command menu. If No One is Enrolled in the HandPunch 1. The display appears as follows: ENTER PASSWORD 2. Press the default password for the menu you wish to enter. Press 1 for the Service Menu. Press 2 for the Setup Menu. Press 3 for the Management Menu. Press 4 for the Enrollment Menu. Press 5 for the Security Menu. 3. If Users are Enrolled in the HandPunch 1.
Enter a Command Menu Enter Password 4. Enter the password for the menu you wish to enter. The default passwords are as follows: Press 1 for the Service Menu. Press 2 for the Setup Menu. Press 3 for the Management Menu. Press 4 for the Enrollment Menu. Press 5 for the Security Menu. Press ENTER If you are authorized to use this command, the first command option in the selected menu appears. 7. If you are not authorized to enter this command, the display appears as follows: 5. 6.
HandPunch 3000/4000 Manual Navigating Command Menus Once you have entered a command menu, there are three options available for navigating the command menu system • Press # to enter the command shown on the display. • Press * to step to the next command in the menu. • Press CLEAR to exit the command menu (pressing any numeric key also exits the command menu). If you are in a command’s sub-menu, you may have to press CLEAR multiple times to completely exit the command menu.
Enter a Command Menu This page is intentionally blank.
HandPunch 3000/4000 Manual Programming the HandPunch The HandPunch is programmed via a series of command menus. A summary of the menus and commands is given in Table 6.
Programming the HandPunch The HandPunch automatically assigns Authority Level 0 to users enrolled by the Add Employee command. Authority Level 5 is automatically assigned to users enrolled by the Add Supervisor command. NOTE Until a user has been assigned to Supervisor, every user can access every menu. Once a user has been enrolled using the Add Supervisor (designated as a supervisor), all further user authority levels are assigned.
HandPunch 3000/4000 Manual System Management Onca a HandPunch system is in operation the following commands are used for system management. Supervisor Override – Review employee punch history, add bulk hours or dollars, or record a punch for an employee. This is done through the Management Menu. The instructions for supervisor override begin on page 61. List Users – List the users authorized to use a HandPunch. This is done through the Management Menu.
Programming the HandPunch Service Menu The Service menu commands provide information that help you determine if the HandPunch is performing within normal operating parameters and identify the status of the unit’s inputs and outputs. The following section provides a brief summary of the Service Menu commands. NOTE Navigating the Service Command Menu There are no user serviceable parts inside the HandPunch. Enter the appropriate password to enter the Service command menu.
HandPunch 3000/4000 Manual Calibrate The Calibrate command displays the HandPunch’s exposure values, allowing you to verify these values are within normal operating parameters. The standard operating parameters are shown in Table 8. Table 8: Normal Operating Parameters Parameter Row “r” Column “c” Exposure “e” Normal Range 0 +/- 2 0 +/- 2 100 +/- 20 Status Display The status display command allows you to enable or disable the displaying of the following information.
Programming the HandPunch Setup Menu The Setup menu commands allow you to set the basic operating parameters for the HandPunch unit. The following section provides a brief summary of all the parameters that may be set on a HandPunch unit. NOTE Navigating the Setup Command Menu Once in the Command Menu, you can step through and set the parameters for each command sequentially. You do not have to exit command mode after setting any individual command.
HandPunch 3000/4000 Manual Table 9: Setup Command Menu Setup Menu Password = 2 Set Language Select Language Set Date Format Select Date Format Set Time and Date Month (MM) Day (DD) Year (YY) Hour (HH) Minute (MM) Set Address New Address Set ID Length New ID Length Set T & A Mode a Set Serial RS-422 (Y/N) Select Baud Rate RS-232 Select Baud Rate Use RS-232 for Printer or Host 57
Programming the HandPunch Table 9: Setup Command Menu Setup Menu Password = 2 a Set Serial Verify/Enter IP Address Verify/Enter Gateway Verify/Enter Host Bit Set Output Mode For Lock & Auxiliary (Y/N) For Card Reader Output (Y/N) Upgrade Code a. The Set Serial command has different values based on whether the HandPunch unit is configured for serial or modem communication versus Ethernet communication.
HandPunch 3000/4000 Manual Set Address The Set Address command allows a unique address to be set for each HandPunch in a network. For proper operation, each HandPunch in the network must have a unique address. All units may use any address from 0 to 254. All units are sent with the address set to 1. Set ID Length The Set ID Length command allows you to reduce the number of keystrokes required to enter the ID number by eliminating the use of the ENTER key to complete an ID number entry.
Programming the HandPunch Management Menu The Management menu commands allow you to manage employee data stored in a HandPunch unit. The following section provides a brief summary of the employee data that may be manipulated on a HandPunch unit. Enter the appropriate password to enter the Setup command menu. Once you have entered the command menu, there are three options available for navigating the command menu system. • Press # to enter the command shown on the display.
HandPunch 3000/4000 Manual Table 10: Setup Command Menu Setup Menu Password = 3 List Users Display Print Set User Data User Reject User Time Zone Amnesty Set Restrictions On/Off (Y/N) Supervisor Override The Supervisor Override command allows you to review an employee’s punch record, add or remove bulk hours or dollars to an employee’s punch record, or add a new punch to an employee’s punch record (see “Table 11” on page 62 for a description on Punch Type codes).
Programming the HandPunch Table 11: Punch Type Information T & A Code 1 2 3 4 5 6 7 8 9 15 Type IN Back From Lunch Out Department Code Back From Break -not usedCalled Back to Work Supervisor Entered Hours Supervisor Entered Dollars Supervisor Entered Category List Users The List Users command allows you to display or print a list of all the employees enrolled in a HandPunch.
HandPunch 3000/4000 Manual Enrollment Menu Enrollment is the process of recording a hand image and associating it with an ID number. The first person to enroll in the HandPunch has access to all command menus. This person should enroll using the Add Supervisor command (see page 66). Once a supervisor has been enrolled, all further enrollments use the following rules: • • NOTE Navigating the Setup Command Menu A user enrolled through the Add Employee command (page 66) is assigned Authority Level 0.
Programming the HandPunch Preparation Here are a few guidelines to help you prepare for an enrollment session: • • • • • User Education The HandPunch is easy to use and non-threatening. However, most people have never used a biometric HandPunch. Training users on how the HandPunch works and how to use it will eliminate most fears and concerns before they occur. Inform the users of these facts.
HandPunch 3000/4000 Manual WEB PIN Figure 8-2: Placing Your Hand on the Platen Left Hand Enrollment Some right hands cannot be used in the HandPunch due to disabilities such as missing fingers. You can enroll a user with the left hand facing palm side up. The techniques for left hand enrollment are the same as for standard enrollment. The user should keep the back of the hand flat against the platen and move the fingers against the web pin and the finger pins in the same manner as in standard enrollment.
Programming the HandPunch Enrollment Commands There are three commands available from the Enrollment command menu: • • • Add Employee Add Supervisor Remove User Refer to Table 12 to identify the command you need to perform. Step through all previous commands until you reach the desired command. Table 12: Enrollment Command Menu Service Menu Password = 4 Add Employee ID # Add Supervisor ID # Remove User ID # Add Employee The Add Employee command allows you to enroll a new employee into the HandPunch.
HandPunch 3000/4000 Manual Special Menu The Special menu has one command – Special Enroll. This command accommodates users with disabilities that make it difficult or impossible to use a HandPunch in its standard way. The following section provides a brief description of the Special Menu command. Enter the appropriate password to enter the Special command menu. Once you have entered the command menu, there are three options available for navigating the command menu system.
Programming the HandPunch Special Enroll The Special Enroll command allows a user to be enrolled such that the ID number is the primary criteria for determining access. A hand read is required, but is not verified against any stored identification data. A time zone value can be applied to the Special Enrollment ID number to limit access times (see page 62). The HandPunch default is for no time zone to be applied.
HandPunch 3000/4000 Manual HandPunch Maintenance A minimum amount of system maintenance is required to keep HandPunchs fully functional. HandPunchs should be cleaned periodically to prevent an accumulation of dust from affecting the HandPunch’s readability. User Scores should be reviewed periodically to ensure the HandPunch is performing properly. NOTE Cleaning the HandPunch There are NO user serviceable parts inside the HandPunch.
Appendix A - Tips Appendix A Tips for a successful Installation HandPunch • • • • • • Think of the HandPunch as a camera Clean the HandPunch before it gets dirty Use non-abrasive cleaners such as glass cleaners and non-abrasive and clean cloths Make cleaning the HandPunch part of Janitorial program Do not remove the foam backing from the wall mounting plate Seal any holes made in the wall for wire routing, so that dust will not blow into the HandPunch Location • • • • Mount all HandPunchs in a network
HandPunch 3000/4000 Manual • • -Try again to enroll the same hand -Try to enroll the other hand (with the hand placed upside-down so the thumb still contacts the thumb-pin on the platen) After enrollment, it is a good idea to let the enrollee enter their ID number and practice a verification transaction to ensure that the enrollment was high-quality. If a user consistently fails during verifications days/months/years later, reenroll the user to ensure a high quality and up-to-date enrollment record.
Appendix B - Board Configuration Differences Appendix B Noted Board Configuration Differences Because of Schlage Biometrics’ camera retrofit of the HandPunch some changes have been made to the main PCB and they are listed as follows: • Dipswitches have been removed -comm lines are terminated. -RS-485 is set by wiring jumpers. -memory is reset with a push-button reset and user interface with keypad and LCD. • The labeling of the terminal strips have changed. See “Figure 11-1” on page 73.
HandPunch 3000/4000 Manual Terminal Block Labeling Number 1 2 RJ-11 RJ-11 RJ-11 RJ-11 OLD PCB 12-24 VDC (+) OR VAC 12-24 VDC (-) OR VAC RXRX+ TXTX+ 7 8 9 10 11 12 13 14 REX SWITCH GROUND DOOR SWITCH GROUND AUX IN 1 GROUND AUX IN 2 GROUND 15 16 17 18 19 20 21 22 23 24 25 26 (+) 5 VDC OUTPUT DATA/D0 CLOCK/D1 GROUND LOCK OR CLOCK OUTPUT GROUND BELL OR DATA OUTPUT GROUND AUXOUT 1 GROUND AUXOUT 2 GROUND Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 RJ-11 RJ-11 RJ-11 RJ-11 1 2 NEW PCB (+) 5 VDC OUTPUT DATA/D0 C
Appendix B - Board Configuration Differences Terminal Block Layout New Board Old Board J6 1 1 2 2 J6 - 2 pin Power connector when daisy chaining power to HandReaders RJ-11 - 4 pin Comm connector 7 TS2 8 9 9 10 10 11 11 12 12 13 13 14 TS2 - 6 pin Input connector 14 15 16 TS3 17 1 18 2 19 3 20 4 21 5 22 6 23 7 24 8 TS3 - 8 pin Output connector 25 26 7 8 Any of the grounds coming off of pins 8, 10, 12, 14, 18, 20, 22, 24, and 26 of the "Old Board" can be tied to pin
HandPunch 3000/4000 Manual Memory Reset To reset the memory of the HandPunch follow these steps1. Remove power and battery jumper, if a back up is installed 2. Press down on reset button and apply power 3. Release button 4. Reader will boot to ERASE • • :1 SETUP :9 ALL!!! Press 1 to erase setup i.e. address, outputs, passwords, but retain user database and datalogs Press 9 to erase everything i.e.
Appendix C - Old Board Configuration Appendix C Old Board Configuration Information Wall Plate Installation 1. Loosen the three bottom mounting screws until there is approximately 1/8 inch (3 mm) clearance between the screw head and the wall plate. 2. Remove the HandPunch from its carton. 3. At the base of the HandPunch is a piano hinge with three keyhole shaped slots that correspond with the three lower mounting screws. Align and hang the HandPunch from the three lower mounting screws (see below).
HandPunch 3000/4000 Manual Grounding Terminal 1 and the center pin of jack J12 are connected together. Terminal 2 and the sleeve of jack J12 are connected together. Use any one of the following ground terminals to make the earth ground NOTE connection: 8, 10, 12, 14, 18, 20, 22, 24, or 26. Do NOT use terminal 2 to establish the earth ground connection; terminal 2 is not directly connected to ground.
Appendix C - Old Board Configuration Wiring Connections Once the HandPunch is attached to the wall plate the wiring connections to the HandPunch can be made (see Figure 13-3 below).
HandPunch 3000/4000 Manual The following Figures provide sample HandPunch wiring diagrams: • • “Figure 13-6” on page 82 provides a sample Bell Output wiring diagram. “Figure 13-7” on page 83 provides a sample Door Lock Output wiring diagram. • “Figure 13-8” on page 84 provides a sample Request to Exit, Door Switch, and Auxiliary Inputs wiring diagram. • “Figure 13-9” on page 85 provides a sample Auxiliary Outputs wiring diagram.
Appendix C - Old Board Configuration Table 15: TS-3 - Card Reader and Output Connections Terminal Connection 17 Card Reader: Wiegand D1 or Magnetic Stripe Clock Input 18 Card Reader Ground 19 Lock Output or Wiegand D1 or Magnetic Stripe Clock Output 20 Ground 21 Auxiliary Output 0 or Wiegand Data 0 or Magnetic Stripe Data Output 22 Ground 23 Auxiliary Output 1 24 Ground 25 Auxiliary Output 2 26 Ground Table 16: RJ-45/RS-232 Serial Printer Connection J8 Pin Signal Connection 1 RI
HandPunch 3000/4000 Manual Table 17: RJ-11/RS-422 Network Connection J3 Pin Signal 1 Rx+ 2 Rx- 3 Tx- 4 Tx+ J3 Pins 1 2 3 4 Figure13-4: J3 - RJ-11/RS-422 Jack Pinout J4 Pins 1 2 3 4 5 6 7 Figure 13-5: J4 - RJ-45/RS-232 Jack Pinout 81
Appendix C - Old Board Configuration POWER SUPPLY + 1 2 NC 12 to 24 VDC Max. NO BELL 1 1 BELL RELAY WALL TO WHICH THE HAND PUNCH IS ATTACHED HINGE 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 RJ-45/RS-232 Printer Output 7 Optional RJ-45 Ethernet or RJ-11 Modem Power Connection These components are not supplied by Recognition Systems, Inc. 2 The Power Supply shall be a UL Listed Limited Current Power Source for UL 294 Installations.
HandPunch 3000/4000 Manual 1 POWER SUPPLY + 12 to 24 VDC Max.2 NC NO ELECTRIC LOCK1 + OR STRIKE - 1 LOCK RELAY WALL TO WHICH THE HAND PUNCH IS ATTACHED HINGE 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 RJ-45/RS-232 Printer Output 9 7 RJ-11/RS-422 4-wire Network TOP OF THE HANDPUNCH 1 8 Optional RJ-45 Ethernet or RJ-11 Modem Power Connection These components are not supplied by Recognition Systems, Inc.
1 2 N.C. DOOR SWITCH N.O. MOMENTARY 1 AUX INPUT 1 N.C. DOOR SWITCH AUX INPUT 2 2 SWITCH LEGEND N.O. REQUEST TO EXIT Appendix C - Old Board Configuration WALL TO WHICH THE HAND PUNCH IS ATTACHED HINGE 14 13 12 11 10 9 8 7 6 5 4 3 2 1 RJ-11/RS-422 Network Power Connections TOP OF THE HANDPUNCH 1 2 RS-232 Printer Output Optional RJ-45 Ethernet or RJ-11 Modem These components are not supplied by Recognition Systems, Inc.
HandPunch 3000/4000 Manual 1 POWER SUPPLY + 12 to 24 VDC Max.2 NC NO 1 AUXILIARY + DEVICE 1 AUX OUTPUT 0 AUX OUTPUT 1 AUX OUTPUT 2 AUX. RELAY WALL TO WHICH THE HANDPUNCH IS ATTACHED HINGE 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 RJ-45/RS-232 Printer Output 8 7 RJ-11/RS-422 4-wire Network TOP OF THE HANDPUNCH 1 9 Optional RJ-45 Ethernet or RJ-11 Modem Power Connection These components are not supplied by Recognition Systems, Inc.
Appendix C - Old Board Configuration ABA-Track II Magnetic Stripe Card Reader AUX INPUT 1 2 AUX INPUT 2 AUX OUTPUT 1 AUX OUTPUT 2 2 CLOCK GROUND DATA REQUEST TO EXIT Access Control Panel N.C. DOOR SWITCH GROUND CLOCK DATA +5 VDC POWER (SEE NOTE BELOW) SWITCH LEGEND N.C. DOOR SWITCH 1 N.O.
HandPunch 3000/4000 Manual DC-102 RS-232 to 4-wire RS-422 Power Supply Data Converter (P/N DC-102) B DB-25 Serial Port Recognit ion 1 2 4 5 7 8 * No 0 3 6 9 * RS-422 4-Wire (2 Twisted Pairs) RJ-11 Jack Surface or Wall Plate Inc. Clear F1 F2 # No Yes Systems Enter B HandPunch 1 Recognit ion 1 4 7 * No 2 5 8 3 6 9 0 Systems * RS-422 4-Wire (2 Twisted Pairs) Inc.
Appendix C - Old Board Configuration Ethernet Cable Recogniti on 1 4 7 * No 2 5 8 0 3 6 9 Clear F1 F2 # No Yes Connection to Host Computer via Ethernet HandPunch Ethernet Port Systems Inc. Enter HandPunch RS-422 RJ-11 Port Ethernet Unit B R G Y * RS-422 4-Wire (2 Twisted Pairs) RJ-11 Jack Surface or Wall Plate Recogniti on 1 2 4 5 7 8 * No 0 3 6 9 Inc.
HandPunch 3000/4000 Manual RSI Supplied Cable (Black) Recogniti on 1 4 7 * No 5 8 0 2 9 Systems Inc. Clear F1 F2 # No Yes 3 6 Enter Modem Unit HandPunch Modem Port RJ-11 Telephone Outlet HandPunch RS-422 RJ-11 Port B R G Y * RS-422 4-Wire (2 Twisted Pairs) RJ-11 Jack Surface or Wall Plate Recogniti on 1 2 4 5 7 8 * No 0 3 6 9 F1 F2 # No Yes Systems Inc.
Appendix C - Old Board Configuration RJ-45 to Printer Adapter (if required) *Serial Printer WALL TO WHICH THE HAND READER IS ATTACHED RJ-45 Connector HINGE RJ-45 Connector 12 to 24 V AC/DC Input TS-3 TS-2 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 J4 RJ-45 Jack TS-1 9 8 7 6 5 4 3 RS-422 Connection 2 TOP OF THE HAND READER * These components are not supplied by Recognition Systems, Inc.
HandPunch 3000/4000 Manual Setting the DIP Switches The DIP Switch settings perform three tasks for the HandPunch (see Figure 13-15 below): • Set End of Line (EOL) Termination to match the type of termination needed by the network. • Set the Communication Method to match the type of network used. • Erase Memory to clear HandPunch memory to all factory defaults values and also clear all user memory.
Appendix C - Old Board Configuration End of Line Termination Termination helps to ensure clean data signals are transmitted through the network wiring. Termination is applied to the end-of-line (EOL) HandPunch in the network daisy-chain. The factory default setting is for EOL termination to be disabled – switches 1 and 2 OFF. Refer to “Figure 13-15” on page 91 for switch ON/OFF positioning. • • To enable EOL termination at a HandPunch, both switches 1 and 2 must be ON.
HandPunch 3000/4000 Manual Erasing the HandPunch Setup Perform the following steps to erase the configuration data but retain the user database. 1. With system power OFF, set switch 4 ON. 2. Turn system power ON and wait for HandPunch boot information to appear on the display. 3. Turn switch 4 OFF. Erasing the HandPunch Setup and User Database NOTE Perform the following steps to erase both the configuration data and the user database. 1. With system power OFF, set both switches 4 and 5 ON. 2.
Appendix D - Troubleshooting Tips Appendix D Troubleshooting Guide Display Messages During Verification Various messages can appear on the HandPunch’s dispaly during hand verification. These messages are defined in Table 18 below. Table 18: Display Messages During Verification Message PLACE HAND ID VERIFIED REMOVE HAND Definition The platen is ready to receive your hand for verification. You are verified, proceed. Remove your hand and place it on the platen again. Follow proper hand placement rules.
HandPunch 3000/4000 Manual This is called a “lockout”. Before the rejected ID number can be used again, another employee or a supervisor must successfully verify at the HandPunch. • If you enter your ID number, but do not place your hand on the platen, the HandPunch will time-out in about 25 seconds. You can immediately end this time-out by the CLEAR key. Beeper and LED Status During Verification The HandPunch’s beeper and LED status display also displays hand verification information.
Glossary Glossary Address, IP – An Internet Protocol address is a unique address assigned to a computer for communicating over a LAN/WAN. It is made up of 4 sets of numbers, separated by periods (for example, 123.245.78.901). Address, HandPunch – A HandPunch Address is a unique identification number assigned to a HandPunch. Each HandPunch on a site must be assigned its own unique address. AWG – American Wire Gauge is a U.S. standard set of wire conductor sizes.
HandPunch 3000/4000 Manual Wiegand™ Reader – The term “Wiegand Reader” has two meanings depending upon its application. A true Wiegand reader reads a specially constructed card made up of small pieces of magnetic wire. As the card is swiped through the reader, the individual bits of wire generate a unique data signal. This data signal is made up of a Facility Code field (typically 8 bits), an ID number field (typically 16 bits), and parity bits (typically 2 bits) for a total of 26 bits of data.
Warranty Limited Warranty Schlage Biometrics, Inc. (the “Company”) warrants to the original user the products manufactured by the Company (the “Product”) to be free of defects in material and workmanship for a period of one year from the date of purchase by usch user or 15 months from the date of shipment from the factory, whichever is sooner, provided: 1.
Ingersoll Rand’s Security Technologies Sector is a leading global provider of products and services that make environments safe, secure, and productive. The Sector’s market-leading products include electronic and biometric access control systems; time and attendance and personnel scheduling systems; mechanical locks and portable security, door closures and exit devices, steel doors and frames, architectural hardware and technologies and services for global security markets. 408.341.
