AR-B1631 User’s Guide AR-B1631 AMD GX3 , VGA , LAN , PC104+ , 4COM , 4 USB User’ s Guide Edition: 2.
AR-B1631 User’s Guide 1. INTRODUCTION Welcome to the AR-B1631 Single Board Computer. The AR-B1631 board Low power GX3 series Processors with the advanced chipset CS5536(CS5535). This product is designed for the system manufacturers, integrators, or VARs that want to provide all the performance, reliability, and quality at a reasonable price. In addition, the AR-B1631 provides on chip VGA. The VGA, which provides up to True Color (32 bit) 1024x768, or High Color (16 bit) 1280x1024 resolution.
AR-B1631 User’s Guide SPECIFICATIONS CPU: GX3 Chipset: CS5536 or CS5535 RAM memory: Supports DDRA, on-board 200-pin SO-DIMM up to 512MB DDRAM memory module Display Interface: CRT – D-SUB 15-pin female connector LVDS – for 18 bit TFT LCD Panel. Ultra ATA/33/66/100 IDE Interface: Floppy disk drive interface: 2.88 MB, 1.44MB, 1.2MB, 720KB, or 360KB floppy disk drive. Series ports: On-board one D-SUB 9-pin male connector for COM1 with RS-232C. On-board one 2x5x2.
AR-B1631 User’s Guide 2. SETTING UP SYSTEM This chapter describes how to install the AR-B1631. At first, the layout of AR-B1631 is shown, and the unpacking information that you should be careful is described. Overview System Settings 2.
AR-B1631 User’s Guide CN8 JP5 LPT1 J2 DIO1 AUDIO1 CDIN1 COM2 JP1 JRS1 JP6 CN10 JP4 COM4 CN4 CN9 COM3 J5 IR1 J3 2.2 SYSTEM SETTINGS Jumper pins allow you to set specific system parameters. Set them by changing the pin location of the jumper blocks. (A jumper block is a small plastic-encased conductor that slips over the pins.) To change a jumper setting, remove the jumper from its current location with your fingers or small needle-nosed pliers.
AR-B1631 User’s Guide 2.2.3 DIO1 (GPIO) 1 2 9 2.2.4 10 GND XOUT0 XOUT2 XIN0 XIN2 1 2 9 10 +5V XOUT1 XOUT3 XIN1 XIN3 LINE OUT R GND LINE IN R MIC IN GND 1 3 5 7 9 2 4 6 8 10 COM2, COM3, COM4 (RS232) 1 2 9 10 1 3 5 7 9 DCD RX TX DTR GND 2 4 6 8 10 DSR RTS CTS RI NC J2 (CHASSIS CONTROL) J2 ＋ HD LED － POWER ＋ LED － RESET AT ATX 2.2.7 2 4 6 8 10 AUDIO1 (AUDIO) 2.2.5 2.2.
AR-B1631 User’s Guide 2.2.8 J3 (CLEAR CMOS) 1 1-2 2-3 NORMAL CLEAR CMOS 3 2.2.9 CN10 (LCD SETTING) 1 2 5 6 2.2.10 1-3 3-5 2-4 4-6 -SHFCLK SHFCLK 3.3V LCD 5V LCD CDIN1 (CDIN) 1 1 2 3 4 4 2.2.11 CD_L GND GND CD_R CN9 (POWER) 1 2 2 2.2.12 +12V GND 1 CN8 (STAND BY POWER) 3 1 2 3 1 2.2.
AR-B1631 User’s Guide 2.2.14 JP4 (LCD LVDS) 2 1 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 30 2.2.15 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 POWER NC GND NC NC NC NC GND LVDS_TXCLVDS_TX2+ NC LVDS_TX1LVDS_TX0+ LVDS_TX3+ POWER 29 LPT1 (PARALLEL PORT) 1 14 1 2 3 4 5 6 7 8 9 10 11 12 13 13 2.2.
AR-B1631 User’s Guide 2.2.17 J4 (PC104+) A B NC NC A1 B1 C1 D1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 D SERIRQ +5V AD0 AD2 AD1 +5V AD5 GND AD4 AD3 C/BE0# AD7 GND AD6 GND AD9 AD8 GND AD11 NC AD10 NC AD14 AD13 GND AD12 +3.3V C/BE1# AD15 +3.3V SERR# GND PULL UP PAR GND PERR# +3.3V PULL UP STOP# +3.3V LOCK# GND +3.3V TRDY# GND DEVSEL# FRAME# GND IRDY# +3.3V GND AD16 +3.3V C/BE2# AD18 +3.
AR-B1631 User’s Guide 2.2.19 1 9 2.2.20 2.2.21 1 USBA_1 & USBA_2（NOTE 2） 1 5V 2 5V 3 USB1- 4 USB2- 5 USB1+ 6 USB2+ 7 GND 8 9 10 GND GND GND 2 10 USB1 & USB2（NOTE 2） 1 2 3 4 5 6 7 5V USBUSB+ GND 5V USBUSB+ 8 GND JRS1 2 5 1-2 3-4 5-6 6 2.2.22 1 4 2.2.
AR-B1631 User’s Guide NOTE 1： For using both of Hard Disk And Compact Flash, you have to use the ATA33 IDE cable. IF you want to use ATA66/100 mode with Hard Disk, you must put jumper on JP6 and use the special IDE cable. The cable is like below： IDE HOST In usual ATA66/100 cable, the Pin 34 between host and device side are disconnected. In usual ATA66/100 cable the Pin 34 at host side is defined as CABLE ID and connected to ground.
AR-B1631 User’s Guide 4. BIOS CONSOLE This chapter describes the AR-B1631 BIOS menu displays and explains how to perform common tasks needed to get up and running, and presents detailed explanations of the elements found in each of the BIOS menus. The following topics are covered: BIOS Setup Overview Advanced CMOS Setup Peripheral Setup Boot BIOS Exit 4.
AR-B1631 User’s Guide date. Follow the month, day and year format. Highlight the
AR-B1631 User’s Guide Configuration options: [Auto] [LVDS] [TFT] Resolution [800x600] This allows you to choose the display resolution. Refresh Rate [60Hz] This allows you to choose the display Refresh Rate. CPU / MEM / PCI Frequency [Auto] This allows you to setting memory frequency. Configuration options: 100/133/166/200 4.
AR-B1631 User’s Guide 4.3 PERIPHERALS Peripherals Onboard Serial Port 1 [3F8/IRQ4] Choose serial port 1 I/O address. Do not set port 1, 2, 3 and 4 to the same address except for Disabled or Auto. Onboard Serial Port 2 [2F8/irq3] Choose serial port 2 I/O address. Do not set port 1, 2, 3 and 4 to the same address except for Disabled or Auto. Onboard Serial Port 3 [3E8/IRQ11] Choose serial port 3 I/O address. Do not set port 1, 2, 3 and 4 to the same address except for Disabled or Auto.
AR-B1631 User’s Guide Onboard Audio [Enables] Should enable for active AC97 USB1 Controller [Enables] This should be enabled if your system has a USB installed on the system board and you want to use it. Even when so equipped, if you add a higher performance controller, you will need to disable this feature. USB2 Controller [Enables] This should be enabled if your system has a USB installed on the system board and you want to use it.
AR-B1631 User’s Guide 4.5 BOOT BOOT First/Second/Third Boot Device HDD-0 SCSI CDROM HDD-1 USB-FDD USB-ZIP USB-CDROM USB-HDD LAN Disabled Boot Other Device [Enabled] Configuration options: [Enabled] [Disabled]. LAN Boot Select [Disabled] This allows you to enable or disable the LAN Boot function..
AR-B1631 User’s Guide 4.6 BIOS EXIT Exit When you have made all of your selections from the various menus in the Setup program, save your changes and exit Setup. Select Exit from the menu bar to display the following menu. Save & Exit Setup Type “Y” will quit the Setup Utility and save the user setup value to RTC CMOS. Type “N” will return to Setup Utility. . Load Optimized Defaults Selecting this field loads the factory defaults for BIOS and Chipset Features, which the System automatically detects.
AR-B1631 User’s Guide 5. I/O address、IRQ and Memory Mapping 5.
AR-B1631 User’s Guide 5.2 IRQ Mapping 5.
AR-B1631 User’s Guide 6. GPIO Sample Code /*[]======================================================================[]*/ /*|| GPIO Test utility for W83627HF. ||*/ /*|| Date : 10/18/2005 ||*/ /*|| Author : Willy ||*/ /*[]======================================================================[]*/ /*[]======================================================================[]*/ /*|| Include files ||*/ /*[]======================================================================[]*/ #include
AR-B1631 User’s Guide Read_Byte=inportb(IO_PORT_BASE+1); if(Read_Byte&0x01) //GPI10 Show_Byte=Show_Byte|0x01; else if(Read_Byte&0x02) //GPI11 Show_Byte=Show_Byte|0x02; else if(Read_Byte&0x04) //GPI12 Show_Byte=Show_Byte|0x04; else if(Read_Byte&0x08) //GPI13 Show_Byte=Show_Byte|0x08; else if(Read_Byte&0x10) //GPI14 Show_Byte=Show_Byte|0x10; else if(Read_Byte&0x20) //GPI15 Show_Byte=Show_Byte|0x20; else if(Read_Byte&0x40) //GPI16 Show_Byte=Show_Byte|0x40; else if(Read_Byte&0x80) //GPI17 Show_Byte=Show_Byte|0x
AR-B1631 User’s Guide printf("\n>>>>> GPI Test Error <<<<<\n"); return 1; } // return fail printf("\n>>>>> GPI Test End return 0; // return pass <<<<<\n"); } /*[]======================================================================[]*/ /*|| Function : GPO_TEST() ||*/ /*|| Input : BYTE IO_PORT_BASE ||*/ /*|| Change :||*/ /*|| Return : Pass return "0", Fail return "1". ||*/ /*|| Description: Test GPO Pins status.
AR-B1631 User’s Guide if ( argc != 2 ) { Show_Title(); return 1; } clrscr(); // Enter W83627HF Config Enter_Config(IO_PORT_BASE); Init_SIO(IO_PORT_BASE); switch(argv[1][0]) { case 'i': case 'I': //I Key result=GPI_TEST(IO_PORT_BASE); if(result==0) printf("Test Result is Pass."); else printf("Test Result is Fail."); break; case 'o': case 'O': //O Key result=GPO_TEST(IO_PORT_BASE); if(result==0) printf("Test Result is Pass."); else printf("Test Result is Fail.
AR-B1631 User’s Guide char YES_NO_Confirm() { int X_Axis,Y_Axis; char y_n; X_Axis=wherex(); /* Get Cursor X Axis */ Y_Axis=wherey(); /* Get Cursor Y Axis */ while(1) { y_n=getche(); if(y_n=='y' || y_n=='Y') return('y'); else if(y_n=='n' || y_n=='N') return('n'); else gotoxy(X_Axis,Y_Axis); } } /*[]======================================================================[]*/ /*|| Function : Enter_Config() ||*/ /*|| Input : BYTE IO_PORT_BASE ||*/ /*|| Change :||*/ /*|| Return : ||*/ /*|| Description: Enter chip
AR-B1631 User’s Guide outportb(IO_PORT_BASE,0x07); outportb(IO_PORT_BASE+1,0x07); // Set GPIO Port Active outportb(IO_PORT_BASE,0x30); outportb(IO_PORT_BASE+1,0x01); } 26
