AR-B1631ET User’s Guide ACROSSER® AR-B1631ET (Extended Temperature) powered by AMD Geode LX800, EPIC SBC with CRT, LCD, LAN, USB2.0, PCI/104 User’s Guide Edition: 1.
AR-B1631ET User’s Guide Contents 1 INTRODUCTION ........................................................... 4 2 SYSTEM SETUP ........................................................... 7 2.1 AR-B1631ET OVERVIEW .............................................................. 7 2.2 SYSTEM SETTINGS...................................................................... 8 2.2.1 2.2.2 2.2.3 2.2.4 2.2.5 2.2.6 2.2.7 2.2.8 2.2.9 2.2.10 2.2.11 2.2.12 2.2.13 2.2.14 2.2.15 2.2.16 2.2.17 2.2.18 2.2.19 2.2.20 2.2.21 2.2.
AR-B1631ET User’s Guide 5.1 I/O ADDRESS MAPPING............................................................. 23 5.2 IRQ MAPPING ............................................................................. 24 5.3 MEMORY MAPPING.................................................................... 24 6 GPIO SAMPLE CODE ................................................
AR-B1631ET User’s Guide 1 INTRODUCTION Welcome to the AR-B1631ET Single Board Computer, the AR-B1631ET low power AMD Geode LX800 processor board with the advanced chipset CS5536 (CS5535). The board is designed for extreme environments, it can be operated from -40°C to +75°C which can make a lot of outdoor applications available, such as Traffic Control, Vehicle Computer, Remote Workstation, Outdoor Data Acquisition, Aviation or Military industries.
AR-B1631ET User’s Guide AR-B1631ET System Block Diagram SPECIFICATIONS CPU: AMD Geode LX800 Chipset: CS5536 or CS5535 RAM memory: Supports DDR400, on-board 200-pin SO-DIMM socket up to 1GB DDRAM memory module Display Interface: CRT – D-SUB 15-pin female connector LVDS – for 18 bit TFT LCD Panel. Touch Screen Header: shared with COM Ultra ATA/33/66/100 IDE Interface: Floppy disk drive interface: 2.88 MB, 1.44MB, 1.2MB, 720KB, or 360KB floppy disk drive.
AR-B1631ET User’s Guide Power Req.: +5V 2A and +12V 1A maximum PC Board: 6 layers, EMI considered GPIO: 8pin (4 output and 4 input) TTL compatible PCB Dimensions: 6.5” x 4.
AR-B1631ET User’s Guide 2 SYSTEM SETUP This chapter describes how to install the AR-B1631ET. At first, the layout of the AR-B1631ET is shown, and the unpacking information is described. 2.
AR-B1631ET User’s Guide CN8 JP5 LPT1 J2 DIO1 AUDIO1 CDIN1 COM2 JP1 JRS1 JP6 CN10 COM CN4 COM JP4 CN9 J5 IR1 J3 USB_A USB_A 2.2 SYSTEM SETTINGS Jumper pins allow you to set specific system parameters. Set them by changing the pin location of the jumper blocks. (A jumper block is a small plastic-encased conductor that slips over the pins.) To change a jumper setting, remove the jumper from its current location with your fingers or small needle-nosed pliers.
AR-B1631ET User’s Guide 2.2.3 DIO1 (GPIO) 1 2 9 10 2.2.4 GND XOUT0 XOUT2 XIN0 XIN2 2 4 6 8 10 +5V XOUT1 XOUT3 XIN1 XIN3 AUDIO1 (AUDIO) 1 2 9 2.2.5 10 1 3 5 7 9 LINE OUT R GND LINE IN R MIC IN GND 2 4 6 8 10 LINE OUT L GND LINE IN L GND GND COM2, COM3, COM4 (RS232) 1 9 2.2.
AR-B1631ET User’s Guide 2.2.7 IR1 1 2 3 4 5 1 5 2.2.8 5V NC IRRX GND IRTX J3 (CLEAR CMOS) 1 1-2 2-3 NORMAL CLEAR CMOS 3 2.2.9 CN10 (LCD SETTING) 1 2 5 2.2.10 1-3 3-5 2-4 4-6 6 CDIN1 (CDIN) 1 1 2 3 4 4 2.2.11 CD_L GND GND CD_R CN9 (POWER) 1 2 2 2.2.12 3 1 -SHFCLK SHFCLK 3.
AR-B1631ET User’s Guide 2.2.13 J5 (LCD BACKLIGHT) 1 2 3 4 5 6 1 5 2.2.14 +12V +12V GND BLT GND NC JP4 (LCD LVDS) 2 1 30 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 29 2.2.
AR-B1631ET User’s Guide 2.2.16 BUZZER EXTERNAL 2.2.17 J4 (PC104+) A1 B1 C1 D1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 A NC NC AD5 C/BE0# GND AD11 AD14 +3.3V SERR# GND STOP# +3.3V FRAME# GND AD18 AD21 +3.3V IDSEL0 AD24 GND AD29 +5V REQ0# GND GNT1# +5V CLK GND +12V NC B SERIRQ AD2 GND AD7 AD9 NC AD13 C/BE1# GND PERR# +3.3V TRDY# GND AD16 +3.3V AD20 AD23 GND C/BE3# AD26 +5V AD30 GND REQ2# NC CLK +5V INTD# INTA# NC C +5V AD1 AD4 GND AD8 AD10 GND AD15 PULL UP +3.
AR-B1631ET User’s Guide 2.2.18 JP6 (IDE Cable Select, NOTE 2) Open Close 2.2.19 USBA_1 & USBA_2 (NOTE 2) 1 2 9 10 2.2.20 ATA33 ATA66 above 1 2 3 4 5 6 7 8 9 10 USB1 & USB2 (NOTE 2) 1 2 3 4 5 6 7 8 2.2.
AR-B1631ET User’s Guide 2.2.22 CN4 (RS422 & RS485) 1 1 RS422TX+/RS485TRX+ 2 RS422TX-/RS485TRX3 RS422RX+ 4 RS422RX- 4 2.2.22 CF1 (NOTE 1) NOTE 1: For using both Hard Disk and Compact Flash, you have to use the ATA33 IDE cable. IF you want to use the ATA66/100 mode with the Hard Disk, you must put the jumper on JP6 and use the special IDE cable. The cable is like below： IDE HOST Usually the ATA66/100 cable and Pin 34 are disconnected between host and device side.
AR-B1631ET User’s Guide 3 LCD FLAT PANEL DISPLAY This chapter describes the configuration and installation procedures for LCD displays. LVDS1 AR-B1631E T LCD Panel Backlight connect to J5 Inverter LCD Panel Block Diagram Backlight Power Please visit our web site or contact our technical support department for supports of LCD connecting.
AR-B1631ET User’s Guide 4 BIOS CONSOLE This chapter describes the AR-B1631ET BIOS menu displays and explains how to perform common tasks needed to get up and running, and presents detailed explanations of the elements found in each of the BIOS menus. The following topics are covered: BIOS Setup Overview Advanced CMOS Setup Peripheral Setup Boot BIOS Exit 4.
AR-B1631ET User’s Guide Date & Time Setup Highlight the field and then press the [Page Up] / [Page Down] or [+]/[-] keys to set the current date. Follow the month, day and year format. Highlight the
AR-B1631ET User’s Guide Video Memory Size [8M] Configuration options: [None] [8M] [16M] [32M] [64M] [128M] [254M] Output Display [CRT] This allows you to choose the output of your system display. Configuration options: [CRT] [Flat Panel] [Panel +CRT] Flat Panel Type [Auto] This allows you to choose the flat panel type Configuration options: [Auto] [LVDS] [TFT] Resolution [800x600] This allows you to choose the display resolution. Refresh Rate [60Hz] This allows you to choose the display Refresh Rate.
AR-B1631ET User’s Guide PnP/PCI Reset Configuration Data [Disable] Normally, you leave this field Disabled. Select Enabled to reset the Extended System Configuration Data (ESCD) when you exit the Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the operating system cannot boot. Resources Controlled By [Auto (ESCD)] This field sets control over the IRQ resources by the automatic (ESCD) system or manual assignment of IRQ channels.
AR-B1631ET User’s Guide Onboard Serial Port 1 [3F8/IRQ4] Choose the serial port 1 I/O address. Do not set port 1, 2, 3 and 4 to the same address except for Disabled or Auto. Onboard Serial Port 2 [2F8/IRQ3] Choose the serial port 2 I/O address. Do not set port 1, 2, 3 and 4 to the same address except for Disabled or Auto. Onboard Serial Port 3 [3E8/IRQ11] Choose the serial port 3 I/O address. Do not set port 1, 2, 3 and 4 to the same address except for Disabled or Auto.
AR-B1631ET User’s Guide OnChip IDE Device With this option you can enable or disable your IDE channel and set the PIO mode or UDMA mode. 4.6 BOOT BOOT First/Second/Third Boot Device HDD-0 SCSI CDROM HDD-1 USB-FDD USB-ZIP USB-CDROM USB-HDD LAN Disabled Boot Other Device [Enabled] Configuration options: [Enabled] [Disabled]. LAN Boot Select [Disabled] This allows you to enable or disable the LAN Boot function.
AR-B1631ET User’s Guide 4.7 BIOS EXIT Exit When you have made all of your selections from the various menus in the Setup program, save your changes and exit Setup. Select Exit from the menu bar to display the following menu. Save & Exit Setup Typing “Y” will quit the Setup Utility and save the user setup value to RTC CMOS. Type “N” will return to Setup Utility. Load Optimized Defaults Selecting this field loads the factory defaults for BIOS and Chipset Features that the System automatically detects.
AR-B1631ET User’s Guide 5 I/O ADDRESS, IRQ AND MEMORY MAPPING 5.
AR-B1631ET User’s Guide 5.2 IRQ MAPPING 5.
AR-B1631ET User’s Guide 6 GPIO SAMPLE CODE /*[]=====================================================================[]*/ /*|| GPIO Test utility for W83627HF. ||*/ /*|| Date : 10/18/2005 ||*/ /*|| Author : Willy ||*/ /*[]=====================================================================[]*/ /*[]=====================================================================[]*/ /*|| Include files ||*/ /*[]=====================================================================[]*/ #include #include
AR-B1631ET User’s Guide /////// Input High Test /////////////////////////////////////////////////// printf("\nConnect GPI Pins to High ? [Y/N] .......
AR-B1631ET User’s Guide Show_Byte=Show_Byte|0x40; else Show_Byte=Show_Byte&0xBF; if(Read_Byte&0x80) //GPI17 Show_Byte=Show_Byte|0x80; else Show_Byte=Show_Byte&0x7F; if(Show_Byte==0x00) printf("\nGPI Pins input value ==> 0x%002X",Show_Byte); else { printf("\nGPI Pins input value ==> 0x%002X (should be 0x00)",Show_Byte); printf("\n>>>>> GPI Test Error <<<<<\n"); return 1; } // return fail printf("\n>>>>> GPI Test End return 0; // return pass <<<<<\n"); } /*[]=================================================
AR-B1631ET User’s Guide int main(int argc, char *argv[]) { BYTE IO_PORT_BASE=0x2E; // DATA_PORT = IO_PORT_BASE + 1; int result; if ( argc != 2 ) { Show_Title(); return 1; } clrscr(); // Enter W83627HF Config Enter_Config(IO_PORT_BASE); Init_SIO(IO_PORT_BASE); switch(argv[1][0]) { case 'i': case 'I': //I Key result=GPI_TEST(IO_PORT_BASE); if(result==0) printf("Test Result is Pass."); else printf("Test Result is Fail.
AR-B1631ET User’s Guide /*|| Description: Confirm get 'Y' or 'N' key.
AR-B1631ET User’s Guide void Enter_Config(BYTE IO_PORT_BASE) { outportb(IO_PORT_BASE,0x87); outportb(IO_PORT_BASE,0x87); } /*[]=====================================================================[]*/ /*|| Function : Exit_Config() ||*/ /*|| Input : BYTE IO_PORT_BASE ||*/ /*|| Change :||*/ /*|| Return : ||*/ /*|| Description: Exit chip configuration key.
