AR-B1651 User’s Guide AR-B1651 EBC 3.5”, VIA Processor for VIA PLE133T with VGA(CRT/LVDS), SDRAM PC133, LAN, Audio, Compact Flash User’ s Guide Edition: 1.03 Book Number: AR-B1651-05.
AR-B1651 User’s Guide Table of Contents 0.PREFACE……………. .................................................................................................................................................. 3 0.1 COPYRIGHT NOTICE AND DISCLAIMER .....................................................................................................................................3 0.2 WELCOME TO THE AR-B1651 CPU BOARD...................................................................................................
AR-B1651 User’s Guide 0. PREFACE 0.1 COPYRIGHT NOTICE AND DISCLAIMER This document is copyrighted, 2003, by Acrosser Technology Co., Ltd. All rights are reserved. No part of this manual may be reproduced, copied, transcribed, stored in a retrieval system, or translated into any language or computer language in any form or by any means, such as electronic, mechanical, magnetic, optical, chemical, manual or other means without the prior written permission or original manufacturer.
AR-B1651 User’s Guide 0.6 ORGANIZATION This information for users covers the following topics (see the Table of Contents for a detailed listing): Chapter 1, “Introduction”, provides specifications and packing list. Chapter 2, “Setting Up System”, describes how to adjust the jumpers and the connector settings. Chapter 3,“CRT/LCD Flat Panel Display”, describes the configuration and installation procedure for using LCD and CRT displays.
AR-B1651 User’s Guide 1. INTRODUCTION Welcome to the AR-B1651 Single Board Computer. The AR-B1651 board is EBC board, which Low power VIA C3 series Processors with the VIA ® advanced chipset Apollo PLE133T (VT8601T and VT82C686B). This product is designed for the system manufacturers, integrators, or VARs that want to provide all the performance, reliability, and quality at a reasonable price. In addition, the AR-B1651 provides on chip VGA.
AR-B1651 User’s Guide 1.1 SPECIFICATIONS CPU: On-board VIA C3 Processor 800MHz or Eden 667 MHz Process DMA channels: 7 Interrupt levels: 15 Chipset: VIA ® Apollo PLE133T ( VT8601T Integrated 2D / 3D graphics accelerator and VT82C686B) RAM memory: Supports SDRAM PC133, on-board 144-pin SO-DIMM up to 512MB SDRAM memory module VGA Controller: Embedded VGA controller, Screen Resolution: up to Ture Color(32 bit)1024x768, or High Color(16 bit) 1280x1024.
AR-B1651 User’s Guide 2. SETTING UP SYSTEM This chapter describes how to install the AR-B1651. At first, the layout of AR-B1651 is shown, and the unpacking information that you should be careful is described. Overview System Settings 2.
AR-B1651 User’s Guide 2.2 SYSTEM SETTINGS Jumper pins allow you to set specific system parameters. Set them by changing the pin location of the jumper blocks. (A jumper block is a small plastic-encased conductor that slips over the pins.) To change a jumper setting, remove the jumper from its current location with your fingers or small needle-nosed pliers. Place the jumper over the two pins designated for the desired setting. Press the jumper evenly onto the pins. Be careful not to bend the pins.
AR-B1651 User’s Guide 2.2.3 Hard Disk (IDE) Connector (IDE1) 44 Pin Hard Disk Connector (IDE1) The on-board 44-pin mini-pitched IDE interface is used to let user support either a 3.5" HDD with 44 to 40pin adapter cable.
AR-B1651 User’s Guide 2.2.5 Parallel Port Connector (LPT1) The connector for the parallel port is a 26-pin header connector. 2 1 26 Parallel Port Connector DB-25 1 2 3 4 5 6 7 8 9 10 11 12 13 25 Signal DB-25 Signal -Strobe Data 0 Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 -Acknowledge Busy Paper Printer Select 14 15 16 17 18 19 20 21 22 23 24 25 26 -Auto Form Feed -Error -Initialize -Printer Select In Ground Ground Ground Ground Ground Ground Ground Ground No Used 2.2.
AR-B1651 User’s Guide external ports. If the USB ports are installed, the USB Controller line in the Integrated Peripherals section of the CMOS Setup utility must be set to “Enabled”. USB ports may also require Operating System support for USB devices. USB1 USB1 use an adapter cable to interface with external equipment. 2 1 10 1.VCC 5.DATA3+ 2.VCC 6.DATA4+ 3.DATA3- 7.8.GND 9 4.DATA4- 9.10.GND 2.2.
AR-B1651 User’s Guide JP5 1. +12V 2. GND 3. Enable Panel Backlight 2.2.11 Serial Port (COM1, COM2) AR-B1651 is equipped with two serial ports. COM1 is a standard RS-232 interface. COM2 use an adapter cable to interface with external equipment. When we are configuring P1or P2, COM1 can also be configured as an RS-232 or RS-485 port. A. COM1 USED RS232 & RS485 COM1 1 2 6 3 7 8 4 5 P1 9 P1 P2 P2 9 7 9 7 6 4 6 4 3 1 3 1 RS-485 Factory Preset RS-232 B. COM2 USED RS232 9 1 1.DCD 5.
AR-B1651 User’s Guide 1 2 3 1 N485+ 2 N4853 GND 2.2.14 Touch Screen Connector (TS2) TS2 is a serial port, which is parallel with COM2. It provides another choice when user needs a serial port but need to connect from board directly without connecting through a D-type connector. The typical application is a touch screen panel. 1 2 3 1 RXDF 2 TXDF 3 GND 2.2.
AR-B1651 User’s Guide 1+ 1 2 2- 2.2.18 Infrared Connector (IR1) The Infra-red Header pin assignment is as follows: 1.VCC 2.NC 1 5 3.IR DATA RECEIVER 4.GND 5.IR DATA TRANSFER 2.2.19 LED (J1) 1: Power LED 1 2 2: LAN LED 3: HDD LED (IDE1) 3 Power LED: External LED connector for Watchdog status indication. LAN LED: External LED connector for 10/100M LAN HDD LED (IDE1): External LED connector for primary IDE channel. 2.2.
AR-B1651 User’s Guide 2.2.22 Power Connector (PWR2) The PWR2 is a 4-pin power connector. It’s the standard connector on all Acrosser boards. PWR2 4 3 2 1 1. +12V 2. GND 3. GND 4. +5V 2.2.23 PC/104 Connector (PC1) (1) 64 Pin PC/104 Connector A&B 2 64 1 63 (2) 40 Pin PC/104 Connector C&D 1 39 2 40 Note: If the content in setting is inconsistent with the CD-ROM, please refer to the setting as the priority.
AR-B1651 User’s Guide 3. CRT/LCD FLAT PANEL DISPLAY This chapter describes the configuration and installation procedures for LCD & CRT displays. The following topics are covered: CRT Connector LCD Flat Panel Displays ※ DON’T SUPPORT EXTERNAL VGA CARD 3.1 CRT CONNECTOR (CRT1) The AR-B1651 supports CRT color monitors. It uses an onboard VGA chipset and you can use the VGA RAM 2.4 or 8 MB.
AR-B1651 User’s Guide 4. WATCHDOG TIMER This section describes the use of Watchdog Timer, including disable, enable, and trigger. AR-B1651 is equipped with a programmable time-out period watchdog timer that occupies I/O port 443H. Users can use simple program to enable the watchdog timer. Once you enable the watchdog timer, the program should trigger it every time before it times out.
AR-B1651 User’s Guide 5. BIOS CONSOLE This chapter describes the AR-B1651 BIOS menu displays and explains how to perform common tasks needed to get up and running, and presents detailed explanations of the elements found in each of the BIOS menus. The following topics are covered: BIOS Setup Overview Advanced CMOS Setup Peripheral Setup Boot BIOS Exit 5.
AR-B1651 User’s Guide Date & Time Setup Highlight the field and then press the [Page Up] /[Page Down] or [+]/[-] keys to set the current date. Follow the month, day and year format. Highlight the
AR-B1651 User’s Guide PNP OS Installed [NO] Select Yes if the system operating environment is Plug-and-Play aware (e.g., Windows 95). Swap Floppy Drive [Disabled] This field is effective only in systems with two floppy drives. Selecting Enabled assigns physical drive B to logical drive A, and physical drive A to logical drive B. USB Keybord Support [Disable] SUPPORT USB KEYBORD INIT Display First [PCI SLOT] Initialize the PCI video display before initializing any other display device on the system.
AR-B1651 User’s Guide UART 2 MODE [Standard] Select an operating mode for the second serial port: Normal RS-232C serial port Standard RS-232C serial port IrDA 1.0 Infrared port compliant with IrDA 1.0 specification IrDA SIR IrDA-compliant serial infrared port IrDA MIR 1 MB/sec infrared port IrDA FIR Fast Infrared standard FIR Fast Infrared standard MIR 0.57M 0.57-MB/sec infrared port MIR 1.15M 1.
AR-B1651 User’s Guide 5.4PnP/PCI PnP/PCI Reset Configuration Data [Disable] Normally, you leave this field Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) when you exit Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the operating system cannot boot. Resources Controlled By [Auto (ESCD)] This field sets control over the IRQ resources by the automatic (ESCD) system or manual assignment of IRQ channels.
AR-B1651 User’s Guide 5.5 PC HEALTH PC HEALTH CURRENT CPU TEMP. The onboard hardware monitor automatically detects and displays the motherboard and CPU temperatures. CURRENT SYSTEM TEMP. The onboard hardware monitor automatically detects and displays the motherboard and System temperatures. CURRENT FAN SPEED The onboard hardware monitor automatically detects and displays the CPU, chassis, and power fan speeds in rotations per minute (RPM).
AR-B1651 User’s Guide 5.
AR-B1651 User’s Guide Boot Other Device [Enabled] Select Your Boot Device Priority 25
AR-B1651 User’s Guide 5.7 BIOS EXIT Exit When you have made all of your selections from the various menus in the Setup program, save your changes and exit Setup. Select Exit from the menu bar to display the following menu. Save & Exit Setup Type “Y” will quit the Setup Utility and save the user setup value to RTC CMOS. Type “N” will return to Setup Utility. . Load Optimized Defaults Selecting this field loads the factory defaults for BIOS and Chipset Features, which the System automatically detects.
AR-B1651 User’s Guide 5.8 BIOS UPDATE The BIOS program instructions are contained within computer chips called FLASH ROMs that are located on your system board. The chips can be electronically reprogrammed, allowing you to upgrade your BIOS firmware without removing and installing chips. The AR-B1665 provides the FLASH BIOS update function for you to easily to update to a newer BIOS version.
AR-B1651 User’s Guide APPENDIX A.
AR-B1651 User’s Guide I/O Map: I/O MAP 0x0022-0x003F 0x0044-0x0047 0x004C-0x006F 0x0072-0x007F 0x0090-0x0091 0x0093-0x009F 0x00A2-0x00BF 0x00E0-0x00EF 0x0100-0x0CF7 0x0D00-0xFFFF 0x03B0-0x03BB 0x03B0-0x03BB 0x03C0-0x03DF 0x03C0-0x03DF 0x0A79-0x0A79 0x0279-0x0279 0x0274-0x0277 0xE000-0xE00F 0x01F0-0x01F7 0x03F6-0x03F6 0x0170-0x0177 0x0376-0x0376 0xE100-0xE11F 0xE200-0xE21F 0xFE00-0xFEFF 0x0020-0x0021 0x00A0-0x00A1 0x0040-0x0043 0x0000-0x000F 0x0081-0x0083 0x0087-0x0087 0x0089-0x008B 0x008F-0x0091 0x00C0-0x0
AR-B1651 User’s Guide APPENDIX B.
