AR-B5230 Series User’s Manual AR-B5230 Series CPU Board EPIC form factor, onboard VGA, LVDS with DDR2-SODIMM Built in two LAN, CF type-II Edition: 1.3 Book Number: AR-B5230 Series-08.11.
AR-B5230 Series User’s Manual © Copyright 2006 All Rights Reserved. Manual’s first edition: October 31, 2006 For the purpose of improving reliability, design and function, the information in this document is subject to change without prior notice, which does not represent a commitment on the part of the manufacturer.
AR-B5230 Series User’s Manual Contents 1 INTRODUCTION .............................................................. 4 1.1 1.2 1.3 SPECIFICATIONS ............................................................................. 4 WHAT YOU HAVE ............................................................................ 6 BLOCK DIAGRAM............................................................................. 7 INSTALLATION ................................................................. 8 2.1 2.
AR-B5230 Series User’s Manual 1 INTRODUCTION Welcome to the AR-B5230 Series (5230/5231) EPIC board. The AR-B5230 Series (5230/5231) incorporates the advanced Intel® 915GME(5230)/910GMLE(5231) Chipset. It supports the Pentium M and Celeron M processors, while coming with a 400MHz Front Side Bus. 1.1 Specifications CPU: Socket for Intel uFC-PGA 478 for Pentium M, Celeron M, Coolers required Support CPU type: CM-0.6G/400/512K/BGA(AR-B5231) CM-1.0G/400/0K/BGA(AR-B5231) CM-1.
AR-B5230 Series User’s Manual PCI-104 slot: PS/2: One PS/2 connector for keyboard and mouse GPIO: 8 bit GPIO Watch dog: Software programmable 1~63 Seconds Hardware monitor: CPU voltage CPU and System temperature CPU/System Fan speed control: AT : 12V single voltage input (BIOS default) ATX: Power switch pin header and pin header for external 5VSB input Battery: Lihium Battery, 3V/220mAH OS: Win XP, Win XP Embedded, Win CE, Linux Dimension: 115mm x 165mm (4.528 x 6.
AR-B5230 Series User’s Manual 1.2 What You Have Before you begin to install your AR-B5230 Series (5230/5231) board, please make sure that the following items are inside the AR-B5230 Series (5230/5231) package.
AR-B5230 Series User’s Manual 1.
AR-B5230 Series User’s Manual 2 INSTALLATION This chapter describes the installation of AR-B5230 Series (5230/5231). At first, it shows the Function diagram and the layout of AR-B5230 Series (5230/5231). It then describes the unpacking information which you should be careful with, as well as the jumper/switch settings for the AR-B5230 Series (5230/5231) configuration 2.
AR-B5230 Series User’s Manual z Buttom Side 36.
AR-B5230 Series User’s Manual 2.2 List of Connectors and Jumper Settings 2.2.1 2.2.2 Power input (CN4) SET 1 SIGNAL +12V 2 GND ATX function connector (CN5) SET 1 2 PS_ON 3 +5V_SUS 2.2.3 CPU fan (FAN1) 2.2.4 CPU select jumper (JP7) 2.2.5 SIGNAL GND SET SHORT SIGNAL DOTHAN OPEN BANINES PCI-104 support SERIRQ (JP6) Note: Short this jumper in order to support SERIRQ function. 2.2.
AR-B5230 Series User’s Manual PIN 1 3 5 7 9 2.2.10 SIGNAL +5V USB0USB0+ GND GND PIN 2 4 6 8 10 SIGNAL +5V USB1USB1+ GND GND CF card Master/Slave select jumper (JP4) SET SHORT SIGNAL MASTER OPEN SLAVE 2.2.11 CMOS clear jumper (JP1) 2.2.12 Keyboard lock (J3) 2.2.13 RTC battery connector (CN1) 2.2.14 Keyboard/Mouse connector (KM1) KM 1 2 3 4 5 6 KDT MDT GND VCC KCLK MCLK 1 3 5 2 4 6 Front View 2.2.15 External USB connector (USB1) 2.2.16 GIGA LAN connector (LAN2) 2.2.
AR-B5230 Series User’s Manual PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 SIGNAL GND TD0TD1+ GND TD2TCK+ HPD VCC RED GREEN BLUE VSYNC HSYNC PIN 26 25 24 23 22 21 20 19 18 17 16 15 14 SIGNAL TD0+ GND TD1TD2+ GND TCKSCL1 SDATA1 GND GND GND SCL2 SDATA2 PIN 1 3 5 7 9 11 13 SIGNAL Y-G GND CVBS/Pb-G GND C/Pr-G GND GND PIN 2 4 6 8 10 12 14 SIGNAL N/A N/A N/A N/A N/A N/A N/A SIGNAL /DCDB RXDB TXDB /DTRB GND PIN 2 4 6 8 SIGNAL /DSRB /RTSB /CTSB /RIB PIN 2 4 6 8 SIGNAL /DSRB /RTSB /CTSB /RIB 2.2.
AR-B5230 Series User’s Manual PIN 1 3 5 7 9 SIGNAL /DCDB RXDB TXDB /DTRB GND PIN 2 4 6 8 SIGNAL /DSRB /RTSB /CTSB /RIB 2.2.25 System FAN (FAN2) Note: The FAN will start to work when temperature over 67ºC and stop when temperature below 53ºC. 2.2.26 Switch button (J1) SET 1-2 SIGNAL SPEAKER 3-4 RESET 5-6 POWER BUTTON 2.2.27 RS232/422/485 select jumper (JP2) SET 1-2 SIGNAL RS232 3-4 RS422 5-6 RS485 2.2.
AR-B5230 Series User’s Manual SET 1 SIGNAL TX+ 2 TX- 3 RX+ 4 RX- 2.2.31 LVDS voltage select jumper (JP5) SET 1-2 SIGNAL 3.3V 2-3 5V 2.2.32 Interver connector (CN3) PIN 1 3 5 SIGNAL +12V GND GND PIN 2 4 6 SIGNAL +12V +5V NC 2.2.33 LVDS connector (LVDS1) 2.2.34 DDR2 connector (DDR2SODIMM1) 2.2.35 Type II CF card connector (CN2) 2.2.
AR-B5230 Series User’s Manual 3 BIOS SETTING This chapter describes the BIOS menu displays and explains how to perform common tasks needed to get up and running. It also gives detailed explanation of the elements found in each of the BIOS menus.
AR-B5230 Series User’s Manual 3.1 MAIN SETUP Once you enter the AwardBIOS™ CMOS Setup Utility, the Main Menu will appear on the screen. Use the arrow keys to highlight the item and then use the keys to select the value you want in each item. Note : Listed at the bottom of the menu are the control keys. If you need any help with the item fields, you can press the key, and it will display the relevant information. Option Choice Description Date Setup N/A Set the system date.
AR-B5230 Series User’s Manual 3.2 Advanced Chipset Setup Option Choice Description This category speeds up Power On Self Test (POST) after you have powered up the computer. If it is set to Enable, BIOS will shorten or skip some check items during POST. Quick Power On Self Test Enabled Disabled Full Screen Logo Show Enabled Disabled Select Enabled to show the OEM full screen logo if you have add-in BIOS.
AR-B5230 Series User’s Manual 3.3 Power setup Option Choice ACPI Function Enabled Disabled This item sets Advanced Configurtion and Power Interface.When ATX mode is enabled and AT mode is disabled. ACPI Suspend Type S1&S3 S1(POS) S3(STR) This item sets Advanced Configurtion and Power Interface mode.It is asserted ACPI Function is enable. PWRON After PWR-Fail Always On Always Off Last State Power-Supply Type AT ATX Description This item sets the POWERON State (Default On).
AR-B5230 Series User’s Manual 3.4 PnP/PCI setup Option Choice Description Enabled Disabled Normally, you leave this field Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) when you exit Setup. If you have installed a new add-on and the system reconfiguration has caused such a serious conflict, then the operating system can not boot.
AR-B5230 Series User’s Manual 3.5 Peripherals Setup Option Choice Onboard Serial Port 1 Onboard Serial Port 2 Onboard Serial Port 3 Onboard Serial Port 4 Serial Port 1: 3F8 / IRQ4 Serial Port 2: 2F8 / IRQ3 Serial Port 3: 3E8 / IRQ11 Serial Port 4: 2E8 / IRQ10 USB Controller Enabled Disabled Select Enabled if your system contains a Universal Serial Bus (USB)controller and you have USB peripherals USB 2.
AR-B5230 Series User’s Manual 3.6 PC Health Setup This section shows the parameters in determining the PC Health Status. These parameters include temperatures, fan speeds, and voltages.
AR-B5230 Series User’s Manual 3.7 Boot setup Option First / Second / Third Boot Device/Other Boot Device Choice Hard Disk CDROM USB-FDD USB-CDROM LAN Disabled LAN Boot Select Enabled Disabled Hard Disk Boot Priority N/A Description The BIOS attempts to load the operating system from the devices in the sequence selected in these items.
AR-B5230 Series User’s Manual 3.8 Exit SETUP Option Choice Pressing on this item for confirmation: Save & Exit Setup Save to CMOS and EXIT (Y/N)? Y Description Press “Y” to store the selections made in the menus in CMOS – a special section of memory that stays on after you turn your system off. The next time you boot your computer, the BIOS configures your system according to the Setup selections stored in CMOS.
AR-B5230 Series User’s Manual Type the password, up to eight characters in length, and press . The password typed now will clear any previous password from the CMOS memory. You will be asked to confirm the password. Type the password again and press . You may also press to abort the selection and not enter a password. To disable a password, just press when you are prompted to enter the password. A message will confirm that the password will be disabled.
AR-B5230 Series User’s Manual 25/25
