Manual

ManualsBrandsAcrosser ManualsComputer AccessoriesAR-ES5430FL

Revision :1.1

Revision Description Date

1.0 Release 2008/01/29

1.1 Add new system dimension 2009/06/16

1.11 Change new RS-232/485 Y-cable 2009/7/10

AR-ES5430FL

Installation Guide

Summary of content (18 pages)

PAGE 1
Revision :1.1 AR-ES5430FL Installation Guide Revision Description Date 1.0 Release 2008/01/29 1.1 Add new system dimension 2009/06/16 1.
PAGE 2
Revision :1.1 Contents 1 2 3 Introduction to AR-ES5430FL……………………………………….. 3 1-1 Description……………………………………………………….… 3 1-2 Packing List………………………………………………………… 3 1-3 Main system………………………………………………………. 4-5 Procedure of Assembly/Disassembly……….……………………… 6 2-1 Installing the 2.5”Hard Disk Drive(HDD)..……………………... 6-9 2-2 Installing CF card……………...….………………………....…… 10 2-3 Installing SO-DIMM….……………………...……………....…… 11-12 2-4 Installing the 2.5”SATA Hard Disk Drive(HDD)(Option)……...
PAGE 3
Revision :1.1 1. Introduction to AR-ES5430FL AR-ES5430FL is a system product mainly for ticket control, navigation, advertising, fleet managements applications. With fanless & dust-proof design, AR-ES5430FL can satisfy the user requirements in any application environment.
PAGE 4
Revision :1.1 1.
PAGE 5
Revision :1.
PAGE 6
Revision :1.1 2. Procedure of Assembly/Disassembly 2-1 Installing the 2.5” Hard Disk Drive (HDD) The following are procedure for install 2.5”HDD device 1.
PAGE 7
Revision :1.1 2. Lock HDD and Bracket together via screws (4pcs) 3.
PAGE 8
Revision :1.1 4. Remove right side door screws (2pcs) in system bottom case 5. Route the HDD cable through the main board 6.
PAGE 9
Revision :1.1 7. Lock HDD bracket to the top case by four screws 8. Insert HDD cable into the HDD module 9.
PAGE 10
Revision :1.1 2-2 Installing CF card The following are procedure for install CF card 1. Remove screws (2pcs) in CF card bracket 2. Install CF card to the bracket 3. Insertion CF card to CF card expansion slot 4.
PAGE 11
Revision :1.1 2-3 Installing SO-DIMM The following are procedure for install SO-DIMM 1. Remove HDD out from the system 2.
PAGE 12
Revision :1.1 3. Re-Install HDD device 4. Lock the bottom case Door screws 2-4 Installing the 2.5”SATA Hard Disk Drive(HDD)(Option) The following are procedure for install 2.5”HDD device 1.
PAGE 13
Revision :1.1 2. Lock HDD and Bracket together via screws (4pcs) 3.
PAGE 14
Revision :1.1 4. Remove right side door screws (2pcs) in system bottom case 5. 6. 7. Route the HDD cable through the main board Lock right side door screws (2pcs) in system bottom case Lock HDD bracket to the top case by four screws 10. Insert HDD cable into the HDD module 11.
PAGE 15
Revision :1.1 2-5 Change from RS232 to RS422/485 by using Y-cable 1. Remove the 4 screws from top cover. 2. Slide the top cover in the direction indicated by the arrow and open it. 3. Pull off the RS232 connector of COM2 from Main board.
PAGE 16
Revision :1.1 4.Change by this terminal to connect with the RS422/RS485 pin header of main board.(Appendix A) 5. Slide the top cover and close it back to the machine.
PAGE 17
Revision :1.1 6. Tighten the original screws.
PAGE 18
Revision :1.1 APPENDIX A COM2 => RS232 (PIN1, Please refer to the AR-B5430 User’s Manual) J5 => RS422/485(PIN1, Please refer to the AR-B5430 User’s Manual) AR-B5430 layout placement APPENDIX B Note: The white dot indicates the pin 1 on the cable.