AR-V5430FL Installation Guide AR-V5430FL Installation Guide Revision 1.
AR-V5430FL Installation Guide Contents 1. INTRODUCTION TO AR-V5430FL .............................. 3 1.1 1.2 Specifications.................................................................................. 3 What You Have ............................................................................... 4 2. SYSTEM DISSECTIONS.............................................. 5 2.1 2.2 2.3 Dimensions ..................................................................................... 5 Front Panel “I/O” ....
AR-V5430FL Installation Guide 1 INTRODUCTION TO AR-V5430FL AR-V5430FL is a Fan-less system product mainly for PC applications in the vehicle industry. With a powerful Intel CPU core & diverse memory card extensions (CF card, SO-DIM), AR-V5430FL can satisfy user requirements in any vehicle industry application environment, especially in the field of vehicle computers.
AR-V5430FL Installation Guide 1.2 What You Have Description Quantity AR-V5430FL 1 Terminal block (Plug) 1 Wall Mount Bracket(Including label for isolation ) 2 Compact Disk 1 SATA Power Cable 1 SATA Cable 1 KB/MS Y Cable 1 Remote Switch Cable 1 2.5”HDD Bracket (Screws-8PCS) 1 GPS External Cable (Option) 1 GPRS External Cable (Option) 1 WiFi External Cable (Option) 1 Fuse 7.
AR-V5430FL Installation Guide 2 SYSTEM DISSECTIONS 2.
AR-V5430FL Installation Guide 2.
AR-V5430FL Installation Guide 2.
AR-V5430FL Installation Guide Item Description Quantity 1 Upper Case 1 2 Bottom Case 1 3 Thermal Module 1 4 Mounting Bracket 2 5 CF Card Bracket 1 6 GPIO Board 1 7 HDD Module 1 8 GPS &GPRS Module 1 9 WiFi Module 1 10 DDRII Lid 1 11 Lock modules of bracket 4 12 GPS/GPRS/WiFi Antenna Inlet 1 13 Fuse 15A for 12V vehicles (default value) 1 8/39
AR-V5430FL Installation Guide 3 PROCEDURE OF ASSEMBLY/DISASSEMBLY 3.1 2.5” Hard Disk Installation The following instructions will guide you step-by-step through the HDD installation. 1. Remove the terminal plug from AR-V5430FL. 2. Unfasten the screw from the top cover of AR-V5430FL.
AR-V5430FL Installation Guide 3. Remove the top cover in the direction shown on the photo below. Remove Push Push 4. Attach the rubbers onto the HDD bracket. Install the rubbers on the HDD bracket.
AR-V5430FL Installation Guide 5. Place HDD body into the HDD bracket and assemble the HDD and the bracket with 4 screws. Screws up 6. Insert the SATA connecter and SATA power cable into the HDD module.
AR-V5430FL Installation Guide 7. Assemble the HDD module and HDD bracket with 4 screws. Screws up 8. Place the HDD module back into the case. 9. Fix the HDD module to the chassis using four screws.
AR-V5430FL Installation Guide 10. Plug the SATA cable and power cable into the mainboard. SATA Power connector SATA Connecter 11. Slide the top cover into the bottom chassis.
AR-V5430FL Installation Guide 12. Finish the HDD installation after fastening the screw.
AR-V5430FL Installation Guide 3.2 Accessory (SO-DIMM, CF Card, SIM Card, Outline bracket) Installation Install SO-DIMM 1. Remove the extension bracket by unfastening the screw. Unfasten screw when installing the SO-DIMM card. 2. Install SO-DIMM following below instructions.
AR-V5430FL Installation Guide Install CF Card 1. Remove the extension CF bracket by unfastening the screws. Unfasten the screws 2. Install the CF card into the bracket. The direction for installing the CF card.
AR-V5430FL Installation Guide 3. Install the CF card module back into CF socket. Direction for installing the CF card module. Install SIM Card 1. Install the SIM card into the SIM socket.
AR-V5430FL Installation Guide Install Outline Bracket 1. Install the fasteners on the case using 4 screws. 2. Install the other side of fasteners on the Outline bracket using 4 screws. 3. Lock the fasteners.
AR-V5430FL Installation Guide 3.3 GPS/GPRS/WiFi Modules Installation 1. Unfasten the 2 screws to release GPS/GPRS brackets. Unfasten the screws. 2. After GPS/GPRS bracket release, please install GPS/GPRS onto the bracket by fastening 4 screws.
AR-V5430FL Installation Guide 3. Install GPS/GPRS modules into the chassis by fastening 2 screws as in step 1. 4. Unfasten the 2 screws to release WiFi bracket. Unfasten the screws. 5. After WiFi bracket release, please install WiFi onto the bracket by fastening 2 screws.
AR-V5430FL Installation Guide 6. Install Wifi modules into the chassis by fastening 2 screws as in step 4. Please do not change the CPU by yourself. Any disassembly and assembly of the the CPU thermal module will cause unexpected damage. Please contact the Acrosser customer service center/FAE for changing the CPU.
AR-V5430FL Installation Guide 4 APPENDIXES (OPTIONAL DEVICES) 4.1 AR-PW0932V Locations (Top Side) 1 PWR1 DC Power Input 7 SW1 DIP switch for mode select.
AR-V5430FL Installation Guide Connectors and Jumper Setting PWR1 DC Power Input PIN SIGNAL 1 DC_IN 2 Key switch 3 GND PIN SIGNAL 1,2 Fuse Out 3,4 Fuse In PIN SIGNAL PIN SIGNAL 1 PWRBTN_IN 2 GND 3 LOC_SW 4 GND 5 KEY_SW 6 GND 7 ENG_STS 8 GND 9 STS_LED 10 GND PIN SIGNAL 1 GND FUSE1 Connect to fuse default 15A J4 Front Panel connector For detailed functions, please refer to the User Manual.
AR-V5430FL Installation Guide JP2 Define KEY_SW, ENG_STS input type J5 Microchip programming connector PWR4 12V(Max 2A), 5V(Max 2A) output STATUS SETTING Open High_active Short Low_active Reserve PIN SIGNAL 1 +12V 2 GND 3 GND 4 +5V PIN SIGNAL 1,2 GND 3,4 +12V PIN SIGNAL 1 RX PWR2 Main +12V(Max 8A) output COM1 Simple UART connector 2 Tx 3 GND NOTE1: (For detailed functions, please refer to the User Manual.
AR-V5430FL Installation Guide Spec Input DC 9V~32V, Output DC 12V (main) / 5V / 5VSB, Total 90W. Definition A. Soft-Off Delay: The period of time from the vehicle ignition or switch being turned off until the power off signal is generated. The delay period is programmable. B. Soft-Off Cycle: The period of time from the power off signal being generated until the system is off. There is only 5VSB (5V Standby) present when the system is off (allows you to turn it on again when the vehicle is restarted) C.
AR-V5430FL Installation Guide not go to high) within 3 minutes after “OFF” pulse is sent, the AR-PW0932V will send the off pulse to the motherboard again. If the motherboard still cannot be shut down normally, the power output will be turned off directly. F. If the ignition turns back to “ON” during the “OFF” Delay, the AR-PW0932V will stay in operation. The “OFF” signal will not be sent to the motherboard. The “OFF” Delay will re-start the next time when the ignition is off. G.
AR-V5430FL Installation Guide 4.
AR-V5430FL Installation Guide 1 2 3 4 5 6 JP1 5V TO RS232 & RESET & POWER LED JP2 PIN HEADER FOR AUDIO IN/OUT CN1 12V & 5V POWER INPUT CN2 PIN HEADER FOR RS-232 SIGNALS CN3 SIM CARD SOCKET CON1 GSM/GPRS MODULE BOARD TO BOARD CONNECTOR Connectors and Jumper Setting JP1 5V TO RS232 & RESET & POWER LED JP2 PIN HEADER FOR AUDIO IN/OUT PIN 1-2 RED LED 3-4 GREEN LED 5-6 SELECT RS232 PIN 10 WITH +5V 7-8 GND PIN SIGNAL PIN SIGNAL 1 LINE_X_R 2 LINE_X_L 3 AUDIO_GND 4 AUDIO_GND 5 MIC_IN 6 AU
AR-V5430FL Installation Guide CN3 SIM CARD SOCKET CON1 GSM/GPRS MODULE BOARD TO BOARD CONNECTOR PIN SIGNAL PIN SIGNAL 1 SIM_VCC 2 SIMRSCDn 3 SIMCKCDn 4 GND 5 X 6 SIMIOCDn PIN SIGNAL 1 SIMCKCDn PIN SIGNAL PIN SIGNAL PIN SIGNAL PIN 11 X 21 2 SIM_VCC 12 X 22 GND 32 RI0 3 SIMIOCDn 13 LPG_RED 23 GND 33 DTR0 43 MICP 4 SIMRSCDn 14 44 MICN 5 LPG_GREEN 15 GND 31 VDD_TOP 41 X 24 GND 34 CTS0 SIGNAL ON_KEY 42 AUDIO_GND TX0 25 GND 35 DSR0 45 X 6 GND 16 X
AR-V5430FL Installation Guide - Storage: -40°C to +85°C CSD data transmissions - Up to 9600 bps - V.110 - Non-transparent mode - USSD support SMS - Point-to-point MO and MT - SMS cell broadcast - Text and PDU mode - Extended Message (EMS) Fax - Group 3, Class 1 Voice - Triple-rate codec for HR, FR, and EFR - Adaptive multi-rate AMR - Basic hands-free operation - Echo cancellation - Noise reduction GPRS data transmission - GPRS class 10: max.
AR-V5430FL Installation Guide 4.3 ACC-V5430-GPS (ER-332-MCX90)) Features SiRF StarⅢ high-performance GPS Chip Set Very high sensitivity (Tracking Sensitivity: -159 dBm) Extremely fast TTFF (Time To First Fix) at low signal level Compact size (40.5mm * 35 mm * 10mm) suitable for space-sensitive application Support NMEA 0183 and SiRF binary protocol Build-in Super-Cap to reserve system data for rapid satellite acquisition.
AR-V5430FL Installation Guide Acquisition Time Reacquisition Hot start Warm start Cold start 0.1 sec., average 1 sec., average 38 sec., average 42 sec., average Dynamic Conditions Altitude Velocity Acceleration Jerk 18,000 meters (60,000 feet) max 515 meters/second (1000 knots) max Less than 4g 20m/sec **3 Power Main power input Power consumption 3.8V ~ 6.
AR-V5430FL Installation Guide Physical Characteristics Inaccuracy: ±0.2mm Interface Connection * Pin-out of the 12-pin interface connector Pin Name Description Type 1 GND Ground 2 VBAT Backup Battery Input 3 VDC 3.8V~5.
AR-V5430FL Installation Guide 11 TIMEMARK 12 GND 1PPS Time Mark Output Output Ground Interface Description * VDC (DC power input): This is the main DC supply for a 3.8V ~ 5.5V power module board. * VBAT (Backup battery): This is the battery backup input that powers the SRAM and RTC when the main power is removed. The typical current draw is 10uA. Without an external backup battery, the module/engine board will execute a cold start after every start.
AR-V5430FL Installation Guide 4.
AR-V5430FL Installation Guide Connectors and Jumper Setting GPIO1 TO AR-B5430 GPIO J1 JUMPER SELECT CN2 DB15 MALE OUTPUT SIGNALS CN3 POWER FORM AR-PW0932V CN4 POWER TO GPRS/GSM (AR-B2011) PIN DEFINE PIN DEFINE 1 GPI0 2 +5V 3 GPI1 4 GPI7 5 GPI2 6 GPI6 7 GPI3 8 GPI5 9 GND 10 GPI4 PIN DEFINE 1-2 NC (DEFAULT) 3-4 NO 5-6 GND (DEFAULT) 7-8 +5V 9-10 +12V 11-12 +EXT PIN DEFINE 1 GPO1 2 GPO2 3 GPO3 4 GPO7 5 +5V 6 GND 7 GND 8 GND 9 +EXT 10 +EXT 11 GPO
AR-V5430FL Installation Guide CN1 POWER TO GPS (Global-Sat ET-332 module) PIN DEFINE 1 +12V 2 GND 3 GND 4 +5V AR-B2012 GPIO board Software API Guide InitGPIO( ) This function is used to set GPIO pin function. You have to call this function before doing any GPIO actions. This function has no return value. SetLevel(unsigned char pin, enum _level level) This function is used to set GPO pin output level. Please refer to Appendix A for the definition of GPO pin.
AR-V5430FL Installation Guide 4.5 Acrosser Wireless Networking WLAN (VNT6656G6A40) Description The Acrosser Networking WLAN embedded system/IA solution is the innovative design of VNT’s wireless chipset. The WLAN module is fully compliant with IEEE’s security and 802.11g standards.
AR-V5430FL Installation Guide Media Access Controller/ Baseband Controller Chip Media Access Protocol VT6656 CSMA/CA (Collision Avoidance) with ACK General USB Interface Operating System Physical Dimension Supports USB2.0/1.1 Standard Windows: 98SE/Me/NT/2000/XP/2003 Ser., Linux (2.6.x), CE (4.2/5.0b) 60x25x5.52mm (L×W×H) Weight Operating Temp. 10g Storage Temp.
