WiFi VoIP Phone WiFi SIP VoIP Phone AVP-2000B Users Manual Copyright® 2005-2006 Acrowave Systems Co,Ltd.
WiFi VoIP Phone -- INDEX -1. OVERVIEWS 5 1.1 LCD DISPLAY 5 1.1.1 Pictograms on LCD 5 1.1.2 Key Buttons 5 2. AVP-2000B MENU TREES 6 2.1 BASIC MENU TREE 6 2.2 PHONEBOOK MENU TREE 8 2.3 MESSAGE MENU TREE 8 2.4 INCALL SOFT MENU TREE 8 3. OPERATIONS 9 3.1 POWER ON / OFF 9 3.1.1 Power On 9 3.1.2 Power Off 9 3.2 SIP REGISTRATION / UNREGISTRATION 9 3.2.1 Registration 9 3.2.1 Unregistration 11 3.3 CALL MAKING / ANSWERING / HANGUP / DND 12 3.3.1 Making Call 12 3.3.
WiFi VoIP Phone 4.1.3.3 LCD Backlight 15 4.1.3.4 Auto Answering 15 4.1.3.5 Localization 15 4.1.3.6 Call Prefix 16 4.1.3.7 Call Forward 16 4.1.3.8 Call Waiting 16 4.1.3.9 Password Change 17 4.1.3.10 Ring-Back Tone Mode 17 4.1.3.11 DTMF Mode 17 4.1.4 ADMIN SETUP 17 4.1.4.1 Networks 18 4.1.4.2 SIP 18 4.1.4.3 Wireless LAN 18 4.1.4.4 NAT 20 4.1.4.5 CODEC 21 4.1.4.6 Initializaionz 22 4.1.4.7 Ping Test 22 4.2 INPUT CHARACTERS 23 4.3 PHONEBOOK 24 4.3.1 OUTBOUND CALL 24 4.3.
WiFi VoIP Phone This page is blank area.
WiFi VoIP Phone 1. OVERVIEWS 1.1 LCD DISPLAYS 1.1.1 Pictograms on LCD 아이콘 설 명 WiFi Signal Strength. : Weak : Strong Out of Service area. Indicates in call state Indicates alarm is on. Indicates that there is/are new message(s) that has/have not been read. Indicates vibration mode or manner mode is on Indicate key-lock state is on Battery life gauge : Full : Sufficient : Shortage 1.1.
WiFi VoIP Phone 2. AVP-2000B MENU TREES This chapter shows the menu trees of AVP-2000B 2.1 BASIC MENU TREES MENU 1.SOUND 1.RING TYPE 2.RING COLOR 1.RING 2.VIBRATOR 3.RING AFTER VIBRATOR 4.RING WITH VOBRATOR 1.RING COLOR 1 2.RING COLOR 2 3.RING COLOR 3 4.RING COLOR 4 5.RING COLOR 5 3.RING VOLUME 2.DIARY 1.ALARM SETTING 1.SET ON/OFF 2.SET TIME 3.SET BELL TYPE 1.ALARM ON 2.ALARM OFF 1.RING COLOR 1 2.RING COLOR 2 3.RING COLOR 3 4.RING COLOR 4 5.RING COLOR 5 2.CALCULATOR 3.USER SETUP 1.DISPLAY TYPE 2.
WiFi VoIP Phone 4.ADMIN SETUP 1.NETWORK 2.SIP SETUP 2.WLAN 1.DHCP 2.STATIC IP 1.AP SELECT 2.SECURITY PHONE ADDRESS NET MASK GATEWAY IP 1.SCAN AP 2.INPUT DIRECT 1.DISABLE 2.ENABLE 1.64 BITS 1.ASCII 2.HEXA 1.ASCII 2.HEXA 2.128 BITS 3.802.1X 4.ROAMING 5.CONNECTION 4.NAT 1.NAT DISABLE 2.NAT ENABLE 1.DISABLE 2.ENABLE 1.ENABLE 2.DISABLE 1.INFRA STRUCT 2.AD-HOC 1.STUN SETUP 2.STATIC NAT 5.CODEC 6.INITIALIZE 1.G.711 2.G.711+G.723 3.G.711+G.729 4.G.711+G.726 1.SOFT RESET 2.RESET PARAM 3.
WiFi VoIP Phone 2.2 PHONEBOOK MENU TREE PHONEBOOK 1:OUTBOUND Î MENU 1:DEL 2:DEL ALL Î MENU Î OK 1:DEL 2:INBOUND CALL Î MENU 1:DEL 2:DEL ALL 3:SEARCH Î MENU Î OK 1:EDIT 2:DELETE Î MENU Î EDIT Î Î Î SHORT NUMBER 4:NET ENTRY NAME PHONE NUMBER 2.
WiFi VoIP Phone 3. OPERATIONS This chaper describes how to operate and configure the AVP-2000B WiFi Phone. 3.1 POWER ON / OFF 3.1.1 Power On Press [ ] button during 2 or 3 seconds to power on the AVP-2000B, then AVP-2000B turn on the power with short beep sound. 3.1.2 Power Off Press [ ] button during 2 or 3 seconds to power off the AVP-2000B, then AVP-2000B turn off with “Good-Bye” message on LCD windows. 3.2 SIP REGISTRATION / UNREGISTRATION 3.2.
WiFi VoIP Phone (Press [S] button to skip this value) - SIP Authenticate Password – Administrator will be supported (Press [S] button to skip this value) - SIP Registration Expire Time – Administrator will be supported (Default value is 3600 seconds) 6) Select “3.Setup WLAN” menu and configure the WLAN informations Input the SSID of AP(Access Point), Encryption mode of WiFi, Security configure, Roaming mode and Connection mode of WLAN in this mode.
WiFi VoIP Phone 3.2.2 UNREGISTRATION The unregistration of AVP-2000B Phone means that administrator or user is to remove registration for AVP-2000B on purpose using already registered on SIP registration server. Following both the means provide removing information in phone registered on SIP registration server. 3.2.2.1 Phone Power Off AVP-2000B Power Off is to remove registered information in AVP-2000B registered on SIP registration server. 3.2.2.
WiFi VoIP Phone 3.3.2 Answering Call AVP-2000B phone is ringing and its LCD window shows sender’s phone number. At this time, press some button except button [CLR] [Power/Off] and then the phone is connected with the sender’s. 3.3.3 Hangup Call To finish calling in AVP-2000B, press button [Power/Off] once and then call is finished. For 3 seconds, call time is indicated. 3.3.
WiFi VoIP Phone 4. Phone Functions 4.1 Menu Descriptions AVP-2000B provides each menu for setup of each function. The composition of whole menu is <1.Menu Tree> Each function is described as follows : 4.1.1 Ring/ Bell Ring/ Bell menu of AVP-2000B provides 3 kinds of function listed below : 1. Ringing Type 2. Ring Color 3. Ring Volume 4.1.1.1 Ringing Type This mode is for setup about how AVP-2000B operates when phone is called.
WiFi VoIP Phone 4.1.2 Phone Diary AVP-2000B provides functions of alarm and calculator for user’s convenience. 4.1.2.1 Alarm This is to provide user with sound of bell by AVP-2000B at setting time with alarm setup. By using direction key or figure key [ ] [ ], they can be selected. [Using Method] [Menu] Î [2:Phone Diary] Î [1:Alarm] Î [1:Alarm] Î [2:Time setting] Î [3:Bell setting] 4.1.2.2 Calculator AVP-2000B provides function of calculator for user’s convenience.
WiFi VoIP Phone 4.1.3.2 LCD Contrast This menu is adjusting contrast of LCD window. There are total 11 steps for adjusting contrast. After selecting menu, by using direction key [ ] [ ], contrast can be adjusted. [Using Method] [Menu] Î [3:User Setup] Î [2:LCD Contrast] 4.1.3.3 LCD Backlight In case that key button of AVP-2000B is pressed or when phone is called, this menu is adjusting time to light up. There are total 4 steps to be selected.
WiFi VoIP Phone [Using Method] [Menu] Î [3:User Setup] Î [5:Localization] Î [1:Using Language] Î [2:Korean] 4.1.3.6 Call Prefix AVP-2000B can be used through PSTN network using connection equipment (example: AVG-5400G) with PSTN network in Wireless Lan circumstances. In this case, for using PSTN network , it is needed to press country line selected number in advance to differentiate from VolP phone generally. This menu provides automatic function for those procedures.
WiFi VoIP Phone 4.1.3.9 Password Change AVP-2000B is using password to remove phone lock function for phone setup change. At this time, user can change password to use. Initial password of AVP-2000B is “0000”. [Using Method] [Menu] Î [3:User Setup] Î [9:Password Change] Î[New Password] Î [Password Confirmation] 4.1.3.10 RingBack Tone Mode When you are phoning with AVP-2000B, you can select sending sound to people answering the phone. [Using Method] [Menu] Î [3:User Setup] Î [10:RingBack Tong Change] Î[1.
WiFi VoIP Phone 1) DHCP This menu is to be used with IP allotted automatically. [Using Method] [Menu] Î [4:Administrator Setup] Î [Password input] Î [1:Network Setup] Î [1:DHCP] Selection 2) Fix IP This menu is for Fix IP. [Using Method] [Menu] Î [4:Administrator Setup] Î [Password input] Î [1:Network setup] Î [1:Fix IP] selectionÎ [Phone IP address] Î [Net Mask Figures] Î [Gateway Address] Input 4.1.4.2 SIP Setup This menu is for setup and change of AVP-2000B registration.
WiFi VoIP Phone 3) Passwordization Setup This is setup menu relevant to safety to be setup with use of wireless lan. Fixed Web key, supplied from IEEE802.11b standard, and be used by this menu. Fixed Web key, provided by AVP-2000B, supports 64 beat, 128 beat, ASKI Word mode and 16 digit mode. [Using Method] [Menu] Î [4:Administrator Setup] Î [4:Wireless Lan Setup] Î [2:Passwordization Setup] Î [2:Setup] Î [1:64 beat mode] Î [1:Character line Mode] Î [Fix Web key] Î [WEP key Number ] Input 4) 802.
WiFi VoIP Phone With use of this menu, after selecting Wireless Lan Contact mode, AP connection have to be tried . For registration of phone, first check state of wireless lan to contact and select contact mode and complete phone registration procedures so that the relevant contact mode works. After contact completed, with the use of function <1.SSID change>, contact the relevant AP or card. [Using Method] [Menu] Î [4:Administrator setup] Î [4:Wireless Land setup] Î [5:contact mode] Î [1:general mode] 4.1.
WiFi VoIP Phone 2. Fix NAT setup This is menu for setup of NAT Port Forwarding Function. NAT server address, NAT SIP Port, and NAT RTP Port can be setup. [Using Method] [Menu] Î [4:Administrator setup] Î [3:NAT setup] Î [1:NAT setup Î [1:Fix NAT setup]Î [NAT server address] Î [NAT SIP Port] Î [NAT RTP Port] Input 4.1.4.5 CODEC Following are voice CODEC which can be used with AVP-2000B. - G.711 a/u law, G.723.1, G.726, G.729a Among the above, AVP-2000B can support another CODEC except G.711 a/u law.
WiFi VoIP Phone [Using Method] [Menu] Î [4:Administrator setup] Î [6:Initialization setup] Î [2:Variables Initialization] Î [1:Yes] 3) Factory Initialization This menu is to return all of AVP-2000B phone state to initial factory setup. [Using Method] [Menu] Î [4:Administrator setup] Î [6:Initialization setup] Î [3:Factory Initialization] Î [Yes] 4.1.3.7 Ping Test This menu is to carry out Ping Test to confirm simply network state and etc. with AVP-2000B.
WiFi VoIP Phone 4.2 Input Characters In case of transmitting short text message or making phonebook, AVP-2000B phone is converted to Input Characters Mode and waiting for characters input. Input characters methods are as follows: If AVP-2000B is converted to characters input mode, pictogram, showing characters input mode, is indicated at upper right side of LCD window. At this state, the wanted characters can be input by figure key and “*” “#”key of AVP-2000B.
WiFi VoIP Phone 4.3 Phone book AVP-2000B provides function of phone book so that user can easily control phone numbers. AVP-2000B can keep memory of 100 phone numbers in shortened numbers. If direction key button [ ] of AVP-2000B is pressed, it enters menu of phonebook. Phone book menu is consisted of following 4 items. 1: Recent sent number, 2:Recent received number, 3:Phone number scan , 4:Phone number registration 4.3.1 OUTBOUND CALL AVP-2000B can store up to 32 phone numbers sent.
WiFi VoIP Phone 4.3.3. SEARCH PHONEBOOK Using function of “phone number registration” of AVP-2000B, it shows all the stored phone numbers and the registered numbers can be found. If “Search phonebook” menu is selected, LCD window shows 3 phone numbers registered in one screen. At this time, user can make it move to next screen for finding required phone numbers by direction key [ ] [ ]. After having the cursor positioned to the required phone list, press button [menu]. Then, it shows menu <1.
WiFi VoIP Phone 4.4 MESSAGE (SIP Instance Message) AVP-2000B provides short text message transmitting and receiving function between equipments using SIP protocol. This message transmitting technique is subject to IEEE RFC-3428 standard. This function of AVP-2000B can be worked by using direction key [ ]. This function provides<1:Text Confirm> and <2:Text letter Writing>. Details are as follows: 4.4.
WiFi VoIP Phone 4.4.2.1 New Message transmitting This is menu for transmitting newly made message. Text Message Text MSG Sending Cont ent s Wr i t i ng 1: Txt MSG Conf i rm 1: Cont ent swr i t i ng Thi s 2: Txt MSG Sendi ng 2: Transmi t t ed Txt message. is t est MSG Cont ent s Wr i t i ng Message store The ot her par t y’ s 1:Yes phone number 2:No : 1234_ AVP-2000B is able to store up to 32 transmitted message. 4.4.2.
WiFi VoIP Phone 4.5 Soft Menus For user’s convenience, AVP-2000B provides following functions at call state. 1.Phone Book, 2:Call Mute, 3:Call Transfer, 4:Call Hold At call state, if you press button [Menu], LCD screen appears to be transferred. At this state, if you press button [cancel], it returns to call state. 4.5.1 Phonebook Please refer to <4.3 phonebook>. 4.5.2 Call Mute At call state in AVP-2000B, call mute function is to prevent user’s own voice from being transmitted to the other party’s phone.
WiFi VoIP Phone 4.5.4 Call Hold At call state, AVP-2000B provides function for temporary call hold. [Using Method] [Call] Î [Menu] Î [4:Call Hold] Î [Phone Number input] Î [Confirm] If call hold function is worked, message “>>call hold<<” blinks at down part of LCD window. In order to remove call hold state of AVP-2000B, do the call hold procedures described above again. Then, call hold is removed and phone is connected again. 4.5.
-Acrowave Systems –CradleAP RF Exposure Statement The device should be used beyond 20cm from the body.
