Instructions Manual

FCC ID:
PRDKB50 Model: KS0 MC:XXXXX Input: XXXV XXX mA Made in Chhina
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and 2) this device must accept interference received, including
interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
TargetCorp. Mpls. MN, 55403 Phone: [phone]
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe
for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product
can be kept as far as possible from the user body or set the device to lower output power if such function is available.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.
NOTE: Do not mix old and new batteries and do not mix alkaline, standard (zinc-carbon) or rechargeable (nicad,
NiMH, etc.) batteries.
Battery life may vary depending on user and computing conditions.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such
marks by TargetCorp. is under license. Other trademarks and trade names are those of their respective owners.
need some help?
Can’t get it to pair? Just have a question?
safety
Do not use near any water source
Do not modify or repair this device
Do not use in high temperatures or extreme weather
Do not use chemical detergents to clean your device, use a soft dry cloth
call us at: 877-698-4883 online at: TargetTechSupport.com
•
•
•
•
Press and
hold Fn
+ F1 ~ F12
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
Press F1 ~ F12
Press and
hold Fn
+ F1 ~ F12
Press F1 ~ F12
Decrease
display brightness
Iecrease
display brightness
Open
Windows Search
Mutes (turns off)
the computer's sound
Decrease
the computer's
volume
Increase
the computer's
volume
Switch to
previous media track
Switch to
next media track
Switch to Bluetooth
channel 1 / device 1
Switch to Bluetooth
channel 2 / device 2
Switch to
wireless USB receiver
channel / device
Play media or
pause current
media track
Function keys
Battery status
LED indicator
Trouble shooting
If it is not working, try below steps to re setup
1.
2.
3.
4.
Turn off your mouse and turn on power again (make sure channel is set on
or )
Make sure to turn on Blueooth on your device
Press and HOLD “ or ” key to set keyboard in pairing mode, make sure
it is discoverable on your device and connect with your keyboard
If it does not work after 10 seconds, repeat step 1 to 3
If it is not working on previous paired devices, make sure to turn on Bluetooth on
that device and set keyboard on correct Bluetooth channel
For example, a tablet has paired with , and a laptop has paired with
Set keyboard on if you want to use keyboard on that tablet
•
connect via Bluetooth in iOS
1.
2.
3.
4.
Turn on your keyboard and set it on either Bluetooth channel or
Click on Apple menu (top left corner of your screen)
Go to System Preferences -> Bluetooth -> Turn Bluetooth on to set up Bluetooth
device
Press and HOLD “ or ” key to set keyboard in discoverable mode so that it
can be seen by you device (LED will start flashing fast in green)
Click on “heyday keyboard” to connect (LED will stop flashing and light up in
green for 3 seconds when pairing is completed)
low battery
If this LED starts blinking, it means
you need to change battery
connect via wireless USB receiver
It is plug and play for USB receiver, make sure power is on, channel is set and then
just plug in USB receiver into available USB A port on device
•
•
•
detailed setup
This keyboard can be paired with up to 3 different devices
Use “ ” keys to change channel from wireless USB receiver channel and
2 other Bluetooth channels
Trouble shooting
If it is not working, try below steps to re-pair keyboard and USB receiver
1.
2.
3.
Turn off your keyboard and re-plug in USB receiver, turn on power (make sure
channel is set on )
Press and HOLD “ ” key (keep keyboard close to receiver)
If it does not work after 10 seconds, repeat step 1 to 3
Short press “ ” keys ONCE will let you switch from each channel
For example, will set this keyboard on “wireless USB receiver”, and its LED indicator
will flash in green 3 ~ 5 seconds, will set it on “Bluetooth channel 1”, its LED will
also flash in green for 3 ~ 5 seconds
connect via Bluetooth on PC
1.
2.
3.
4.
Turn on your keyboard and set it on either Bluetooth channel or
Click on Start Menu (bottom left corner of your screen)
Go to Settings -> Device -> Bluetooth & other devices
Turn on Bluetooth -> Add Bluetooth or other device -> Add a device (Bluetooth)
Press and HOLD “ or ” key to set keyboard in discoverable mode so that
it can be seen by your device (LED will start flashing fast in green)
Click on “heyday keyboard” to connect (LED will stop flashing and light up in green
for 3 seconds when pairing is completed)
wireless keyboard
battery compartment
battery cover
wireless
USB receiver
top
bottom
ON / OFF
switch
connect / pairing
LED indicators
2 x AAA battery
wireless USB receiver
Bluetooth channel 1
Bluetooth channel 2
connection channel for
included
Wireless Keyboard (connect via wirelesss USB receiver or Bluetooth)
USB receiver
2 x AAA battery
•
•
•
front back
front back
5.6in = 142.24mm
4in = 101.6mm
Size: 8 in x 5.6 in = 203.2 x 142.24mm
KS0+MQZ(2.4G-BT wireless keyboard)
for heyday Instructions Manual