Deluxe RF Laser Mouse With Office hot key OWNER'S GUIDE CAUTION : To use this mouse properly, please read the user's guide before installation
Welcome Your mouse uses a new generation technology – laser module that replaces the traditional LED mouse and provides amazing tracking ability. The laser module accurately scans the surface in 30 times sensitive of LED optical mouse. You can work with your mouse in most surfaces perfectly. Safety Notice 1. 2. 3. This product complies with IEC 60825-1, class 1 laser product. Your product complies with FCC and CE rules. This product has no serviceable parts.
SETUP the Mouse The Mouse is connected to your computer via a cable. plug in your computer by a USB port or a mouse port. It needs to PS2 Mouse Port For PS/2 mouse port installation Please turn off your computer before installing your mouse. Plugging and unplugging cables to your computer's mouse port while the computer is running can damage the mouse port or your Computer. USB Port For USB port installation Windows 98 (or higher) and Macintosh OS 8.6 (or higher) are required for USB port installation.
Installing the batteries Step 1 Press the tag on the battery compartment cover of the mouse and pull up. Step 2 Insert the batteries as shown inside the battery compartment. Step 3 Replace the cover.
Functional Introduction: Low power LED Channel reset button Office hot key Mouse wheel OFF/ ON switch Previous / Next page Setup the connection Rf channel between the Mouse and the Receiver Push 1 Push 2 Push the channel reset button on the mouse Push the channel reset button on the receiver I f the cursor does NOT move after 30 seconds, please re-do the steps above.
Green LED FLASH 0.5 sec.
Using your mouse How to use the wheel Your mouse has a wheel that functions both as a wheel for Windows Scrolling and also as a customized button. It can be used as a standard mouse button, click (press down) the wheel. To Use the Middle Button, Directly Press down the Wheel. For scrolling the screen, simply move the wheel. Software Installation Please follow the steps below to install your mouse driver: 1. Follow the instruction on screen; system will install the Driver automatically. 2.
Utility & Office hot key: The Office hot key provides you with easy way to customize your mouse operations and total control over the screen without using taskbar or start menu. You just need to press the Office Selector Key on your mouse then round shaped quick panel will pop up. You will see eight items on the Quick Panel providing effective accessibility for most frequently used Windows applications including Word, Excel and PowerPoint. You just need to click on the item you want to launch.
Utility Settings Double click the mouse icon on the right bottom corner of the Windows screen to get into the setting window. You can add new functions to your Quick Panel for making your own frequently Command Quick Panel in the Office applications. Example: Add a “save” functional key in the Quick Panel for the Word application.
5 Important Notes: • • • • • Please follow the instructions contained in the instruction manual. Do not try to disassemble or replace parts in the product. Do not put the product in water or on any wet surface; if this occurs quickly remove from the computer and take to your nearest dealer for repair. To avoid electrocution, please do not pick up the device when your hands are wet. Do not put the product near a heat source or put the product in high temperatures.
Troubleshooting Mouse does not work upon installation Try one or more of the following: z Make sure you have installed the Driver correctly. z Make sure the receiver cable is plugged into the right mouse port. z Unplug the Mouse and then plug in the mouse again. Make sure that Mouse had been detected by the Operating Systems properly. z Make sure your mouse port has the proper configuration. Refer to your computer documentation for the correct port configuration. z You may have other system devices (e.g.
MP1 Work Basis Mouse (optical): 1. When the mouse was moved, the optical sensor would detect the different between two points, and then sensor will send the signal to the MP1. 2. The MP1 will encode the signal and modulate the signal that uses FSK modulation type). 3. Through the 27 MHz RF circuit transmit the modulation signal. Receiver: 1. When the receiver receives the modulation signal will demodulate signal through RF circuit. And responds signal to MP1. 2.
FCC ID LABEL FORMAT AND LOCATION Applicant: Acrox Technologies Co., Ltd. FCC ID: PRDMPO008PXOX FCC ID: PRDMPO008PXOX This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
