Access Control System EXP-06E Single Door Access Controller Installation and Operation Instructions Version 6.
EXP-06E Access Control System Installation Instruction 1. INTRODUCTION The ACS Access Control System is a powerful software based time recording, access control and integrated security system designed to meet the most demanding access control and point monitoring applications. Programming the system is done from a cost effective IBM compatible microcomputer. Cards can be added or deleted in seconds. All events can be archived for future reference and report generation.
EXP-06E Access Control System Installation Instruction 2. Hardware Requirements Computer : CPU: Hard disk space: RAM: OS: Motherboard: Display: Input Device: Floppy Disk: CD-ROM Drive: Printer: Modem: Pentium III 800MHz 500MB 64MB Windows 98SE English / Chinese version (big5 version) 1 x RS232 port SVGA 800x600 resolution color monitor with 16 bits color Enhanced 101 keyboard and serial mouse 1 x 3.5” high-density floppy disk drive 1 x 8X CD-ROW Drive 24pin dot matrix (360dpi)/laser jet (300dpi).
EXP-06E Access Control System Installation Instruction 3.
EXP-06E Access Control System Installation Instruction 4.
EXP-06E Access Control System Installation Instruction 6. User Card Operation Procedures 6.1 Present Card Only Place the card on the present card area. If the entrance is permitted, the proximity card reader will sound a long "beep". Then the door lock will be released with a certain time defined by supervisor.
EXP-06E Access Control System Installation Instruction proximity card reader will sound three sort " beep-beep-beep". For security reason, the key Operation can only be tried 3 times. After than the Key Operation will be terminated for this card only. Card operations then need to reset the termination. 6.5 Turn ON/OFF Control Relay by User Card with Pin Code At this function mode, user must press "9" button in the keypad and hold it on and present the card.
EXP-06E Access Control System Installation Instruction Otherwise, the proximity card reader will sound three sort "beep-beep-beep" for rejected active by "INVALID AUTHORIZE LEVEL" OR "WRONG PIN CODE". Remark : Duress Pin Code is the current user pin code add one. i.e. If the user pin code is 0001 then the duress pin code should be 0002. 6.8 Present Card with Duress Pin Code If duress alarm function interfaced with alarm control panel, user can use this function for under duress access.
EXP-06E Access Control System Installation Instruction 7. INSTALLATION OF EXP-06E 7.1 Overview of EXP-06E The EXP-06E has two-reader port and one keypad port, capable of handling three relay outputs. The EXP-06E is housed in a 16 AWG metal wall-mounted cabinet. The static RAM consumes minimal power for storing memory and data. The EXP-06E is compatible with PC using Access Control System.
EXP-06E Access Control System Installation Instruction 7.3 Equipment Wiring /requirement of EXP-06E 7.3.1 Readers (In/Out) & Keypad 1. Do NOT wiring with any other high power cable. E.g. 220V AC 2. Do NOT install near switches that produce large amount of spark. E.g. Light. 3. Choose linear power supply for the readers instead of switching power supply. 4. Follow the cable wiring specification by the manufacturer of readers. 7.3.2 Door Lock Relay Output (IMPORTANT) 1.
EXP-06E Access Control System Installation Instruction 7.4 Connecting the EXP-06E to a host The connector – G, H, I connects a single EXP-06E to the host computer via RS-232C format. Multiple EXP-06E communicates with host from connector – F, E via RS-485 format. But the EXP-06E chain must communicate with host through an RS232/RS-485 converter. 7.4.1 Configuring the EXP-06E Jumpers Configure EXP-06E jumpers JP4 & JP5 for the host communication format you are using.
EXP-06E Access Control System Installation Instruction 7.4.4 Configuring the RS-485 Interface Card RS-485 Interface Card is used to communicate PC and EXP-06E via RS-485 format. Make sure there are no other devices using COM3 and I/O address (03E8-03EF) in the PC before installation. If there is a device using COM3 already, readdress the port and address of this device. 1. 2. 3. 7.4.5 Install the interface card into an ISA expansion slot on the PC motherboard.
EXP-06E Access Control System Installation Instruction 7.7. Configure Alarm Relay The alarm relay can be activated at the following events: 1. Break In Alarm This is used to enable the break in signal of door. if the door is opened by other matters except door opening door release button or present card or key-in process, the alarm relay will be turned ON and a "alarm occurred" signal will be stored in memory of the access controller. p.s.
EXP-06E Access Control System Installation Instruction 8. Specification 8.1 EXP-06E Access Controller CPU Memory Clock & Data Memory back-up battery : : : Communication Interface Data Transfer Rate (Local & Remote) Input Voltage : : : Power Consumption : Temperature Humidity : : Satcom Systems (International) Co., Ltd. 8031 32KB Non-charge 1 month backup during power failure RS232 and RS485Converter type 9,600 bps AC 220 - 240V / 50 - 60Hz 12V AC / DC Approx. 8W - AC 220V - 240V Approx. 0.
EXP-06E Access Control System Installation Instruction FG AC220V Input A C -L Model : SFLA-030-2L 12V B (-) A C -N Switching Power Supply 12V A (+) DC2 12V (-) COM 12V (+) DC1 Connected to EXP-06 Controller Board 12V Output for Electric Lock (2 am p.