User's Manual

ManualsBrandsACS ManualsUniversal RemoteACS Universal Remote 3200

3200 Series

CS 3216 Operators Manual 1

3200 Series PID Temperature Controllers

ACS Custom Manual Issue 1.0

3216 Controllers

Issue 1 of this Handbook applies to software versions 2.09 and above for PID controller and includes:

• Remote Setpoint Input Option RCL

• Programmer Cycles

Contents

1. Installation and Basic Operation..........................................................................................................3

1.1 What Instrument Do I Have?................................................................................................................................. 3

1.2 What Firmware Do I Have?................................................................................................................................... 3

Firmware V2.09 (Modbus) Firmware V2.50 (SPI)............................................................................................. 3

What Instrument Do I Have?.............................................................................................................................................. 4

Order Code........................................................................................................................................................................... 4

2. Wiring .....................................................................................................................................................5

2.1 Terminal Layout 3216 Controller.......................................................................................................................... 5

3. Panel Layout...........................................................................................................................................6

3.1 Front Panel Layout ................................................................................................................................................. 6

3.1.1 To Set The Target Temperature. .......................................................................................................................... 6

3.1.2 Alarms.................................................................................................................................................................. 6

3.1.3 Alarm Indication .................................................................................................................................................. 6

3.1.4 Auto, Manual and Off Mode ................................................................................................................................ 7

3.1.5 To Select Auto, Manual or Off Mode................................................................................................................... 7

4. Operator Level 1 ....................................................................................................................................8

4.1.1 Level 1 Operator Parameters................................................................................................................................ 8

5. Operator Level 2 ....................................................................................................................................8

5.1 To Enter Level 2...................................................................................................................................................... 8

5.2 To Return to Level 1 ............................................................................................................................................... 8

5.3 Level 2 Parameters.................................................................................................................................................. 8

6. Access to Further Parameters...............................................................................................................9

6.1.1 Level 3.................................................................................................................................................................. 9

6.1.2 Configuration Level ............................................................................................................................................. 9

6.1.3 Selecting Recipes (Configuration Level) ............................................................................................................. 9

6.1.4 To Select Access Level 3 or Configuration Level................................................................................................ 10

6.2 Parameter lists......................................................................................................................................................... 11

6.2.1 To Choose Parameter List Headers ...................................................................................................................... 11

6.2.2 To Locate a Parameter.......................................................................................................................................... 11

6.2.3 How Parameters are Displayed ............................................................................................................................ 11

6.2.4 To Change a Parameter Value.............................................................................................................................. 11

6.2.5 To Return to the HOME Display.......................................................................................................................... 11

6.2.6 Time Out .............................................................................................................................................................. 11

6.3 Navigation Diagram................................................................................................................................................ 12

7. Custom Scrolling Text ...........................................................................................................................12

Custom Configurations........................................................................................................................................................ 12

7.1.1 Master Parameter List .......................................................................................................................................... 13

8. Diagnostic Alarms..................................................................................................................................20

8.1.1 Out of Range Indication ....................................................................................................................................... 21

9. Digital Communications........................................................................................................................22

9.1 Digital Communications Wiring............................................................................................................................ 22

9.1.1 RS232................................................................................................................................................................... 22

9.1.2 RS485 (2-wire)..................................................................................................................................................... 22

9.2 Digital Communications Parameters..................................................................................................................... 23

9.3 Modbus Parameter Addresses............................................................................................................................... 24

9.4 SPI Parameter Addresses....................................................................................................................................... 25

9.5 DEVID 20, 21 & 22.................................................................................................................................................. 25

9.5.1 ECHO................................................................................................................................................................... 25

9.5.2 PROCESSING ..................................................................................................................................................... 27

Summary of content (46 pages)

PAGE 1
3200 Series 3200 Series PID Temperature Controllers ACS Custom Manual Issue 1.0 3216 Controllers Issue 1 of this Handbook applies to software versions 2.09 and above for PID controller and includes: • Remote Setpoint Input Option RCL • Programmer Cycles Contents 1. Installation and Basic Operation .......................................................................................................... 3 1.1 What Instrument Do I Have?....................................................................
PAGE 2
3200 Series 9.6 9.6.1 DEVID 26 & 27 ....................................................................................................................................................... 30 ECHO................................................................................................................................................................... 30 10. Remote Setpoint (Optional)...................................................................................................................
PAGE 3
200 Series 1. Installation and Basic Operation 1.1 What Instrument Do I Have? Thank you for choosing this 3200 series Temperature Controller/Programmer. A universal input accepts various thermocouples, RTDs or process inputs. Up to three 3216 outputs can be configured for control, alarm or re-transmission purposes. Digital communications and a current transformer input are available as options.
PAGE 4
3200 Series What Instrument Do I Have? K Order Code 1 2 3 4 5 6 7 8 9 10 11 12 13 14 3216 1. Model No. 1/16 DIN size 7. Fascia colour/type 5. AA Relay (OP4) 3216 Disabled X Green G Relay (Form C) R Silver S Wash down fascia (2) W 2. Function Controller 6. Options CC Programmer CP Not fitted XXX valve controller VC RS485 & Digital input A 4XL Valve programmer VP 3. Power Supply 24Vac/dc VL 100–240Vac VH 4.
PAGE 5
3200 Series 2. Wiring Ensure that you have the correct supply for your indicator ! Check order code of the controller supplied 2.1 Terminal Layout 3216 Controller Second Setpoint + Output 1 Or Retransmission Output 2 + 1A CT AA C AB LA AC HD VI - - 1B + + 2A - - Line Supply 100 to 240Vac 50/60Hz OR Low Voltage Supply 20 -29Vac/dc 2B COM L A(+) N B(-) HE V+ HF V- Output 4 (AA Relay) + PV Input + + + 2.
PAGE 6
3200 Series 3. Panel Layout 3.1 Front Panel Layout ALM Alarm active (Red) Measured Temperature (or Process Value ‘PV’) OP1 lit when output 1 is ON (normally heating) OP2 lit when output 2 is ON (normally cooling ) Target Temperature (Setpoint ‘SP’) OP3 lit when output 3 is ON OP4 lit when output 4 relay is ON (normally alarm) SPX Alternative setpoint in use (e.g. setpoint 2) REM Remote digital setpoint.
PAGE 7
3200 Series 3.1.4 Auto, Manual and Off Mode The controller can be put into Auto, Manual or Off mode – see next section. Auto mode is the normal operation where the output is adjusted automatically by the controller in response to changes in the measured temperature. To Select Auto, Manual or Off Mode Press and hold than 1 second. In manual mode the MAN beacon will be lit, Band and deviation alarm are masked, the auto-tuning timer and programmer functions are disabled.
PAGE 8
3200 Series 4. Operator Level 1 4.1.1 5. Operator Level 2 Level 1 Operator Parameters A minimal list of parameters are available in operator Level 1 which is designed for day to day operation. Access to these parameters is not protected by a pass code. Level 2 provides access to additional parameters. Access to these is protected by a security code. 5.1 To Enter Level 2 . Press to step through the list of parameters. The mnemonic of the parameter is shown in the lower display.
PAGE 9
3200 Series 6. Access to Further Parameters Parameters are available under different levels of security and are defined as Level 1 (Lev1), Level 2 (Lev2), Level 3 (Lev 3) and Configuration (Conf). Level 1 has no passcode since it contains a minimal set of parameters generally sufficient to run the process on a daily basis. Level 2 allows access to parameters which may used in commissioning a controller or settings between different products or batches.
PAGE 10
3200 Series 6.1.4 To Select Access Level 3 or Configuration Level Do This The Display You Should See To Select Level 3 1. From any display press and hold for more than 5 seconds Lev 3 go to 0 CODE 2. Press or the passcode for Level 3 3. When the LEV3 GOTO view is shown, as in paragraph 1 above, press 11 CODE to enter Additional Notes The display will pass from the current operating level, for example, Lev 1 to Lev 3 as the button is held down.
PAGE 11
3200 Series 6.2 Parameter lists Parameters are organised in lists. The top of the list shows the list header only. The name of the list header describes the generic function of the parameters within the list. For example, the list header ‘ALARM’ contains parameters which enable you to set up alarm conditions. 6.2.1 To Choose Parameter List Headers Press . Each list header is selected in turn every time this key is pressed. 6.2.3 How Parameters are Displayed As shown above.
PAGE 12
3200 Series 6.3 Navigation Diagram The diagram below shows the all list headings available in configuration level for 3216 controllers. The parameters in a list are shown in tables in the following sections of this manual together with explanations of their meanings and possible use.
PAGE 13
3200 Series 7.1.1 Master Parameter List INPUT LIST I NPUT Name Scrolling Display Parameter Description Value IN.TYP INPUT TYPE Selects input linearisation and range See manufacture manual for input types available Default UNITS DISPLAY UNITS Display units shown on the instrument none No units - only for custom linearisation o Celsius o Fahrenheit o Kelvin PErc % nnnn No DP nnn.n One DP nn.nn Two DP C F k DEC.
PAGE 14
3200 Series INPUT/OUTPUT LIST 1 ‘I O -1 ’ Name Scrolling Display 1.SRC.A I/O 1 SOURCE A 1.SRC.B I/O 1 SOURCE B 1.SRC.C I/O 1 SOURCE C 1.SRC.D I/O 1 SOURCE D Parameter Description These parameters only appear when the channel function is a Digital output, i.e. 1.FUNC = d.out Selects an event status to be connected to the output channel. The output status is the result of an OR of Src A, Src B, Src C, and Src D Up to four events can, therefore, operate the output 1.D.
PAGE 15
3200 Series and vice versa 2.SRC.A 2.SRC.B I/O 2 SOURCE A I/O 2 SOURCE B 2.SRC.C I/O 2 SOURCE C 2.SRC.D I/O 2 SOURCE D These parameters only appear when the channel function is a Digital OP, i.e. 2.FUNC = d.Out OP none No event connected to the output AL1 Alarm 1 * AL2 Alarm 2 * Output power demand re-transmission AL3 Alarm 3 * Selects an event status to be connected to the output channel. AL4 Alarm4 * ALL.A All alarms nw.
PAGE 16
3200 Series 4.SENS SENSE To configure the polarity of output channel 4 nor Normal Inv Inverted nor Conf LOGIC INPUT LIST ‘l a ’ / ‘LB’ Name Scrolling Display Parameter Description Value Default Access Level L.TYPE LOGIC INPUT TYPE Input channel type L.IP Logic input As order code Conf Read only L.d.i n LOGIC INPUT FUNCTION To configure the function of the digital input none Input not used Ac.AL Conf Ac.AL Alarm acknowledge SP2 Setpoint 2 select Loc.
PAGE 17
3200 Series CONTROL LIST ‘CTRL’ Parameter Name Parameter Description (Scrolling Display) Value CTRL.H HEATING TYPE Selects the channel 1 control algorithm. Different algorithms may be selected for channels 1 and 2. In temperature control applications, Ch1 is usually the heating channel, Ch2 is the cooling channel. Pid PID off Heating off on.of On/Off MTr Valve position control COOLING TYPE Selects the channel 2 Control algorithm. Different algorithms may be selected for channels 1 and 2.
PAGE 18
3200 Series SAFE SAFE OUTPUT POWER To set the output level in a sensor break (open circuit) condition -100.0 to 100.0% limited by OP.HI and OP.LO 0.0% L3 F.MOD FORCED MANUAL OUTPUT MODE Selects how the loop behaves on transfer from Auto to Manual. Transfer from Manual to Auto is always bumpless. none Transfer between Auto/Manual/Auto is bumpless none L3 SteP Transfer from Auto to Manual, the output goes to a pre-set value (F.
PAGE 19
3200 Series TIMER LIST ‘t i m e r ’’ Name Scrolling Display Parameter Description Value Default Access Level THRES TIMER START THRESHOLD To set the maximum deviation between SP and PV before the timer starts. Off or 1 to 3000 Units above and below setpoint Off L3 Dwell timer and Programmer only ENd.T TIMER END TYPE To determine the action which takes place when the timer has timed out. Dwell timer and Programmer only SS.SP SOFT START SETOINT SS.PWR SOFT START POWER LIMIT T.
PAGE 20
3200 Series Name Scrolling Display Parameter Description Value ucal USER CALIBRATION To select low and high offset state or reset to no offsets. IdLe Normal operating state Lo Low offset Hi High offset Default Access Level IdLE L3 only Remove high and low offsets rEST The following parameters appear when calibrating the controller ie UCAL = Lo or Hi c.adj CALIBRATION ADJUST To set an offset value.
PAGE 21
3200 Series 8.1.
PAGE 22
3200 Series 9.1.2 9. Digital Communications Digital Communications (or ‘comms’ for short) allows the controller to communicate with a PC or a networked computer system. Digital communications is not available in 3116 controllers. This product conforms to MODBUS RTU ® protocol a full description of which can be found on www.modbus.org. Two ports are available both using MODBUS RTU communication facilities: 1.
PAGE 23
3200 Series 9.2 Digital Communications Parameters The following table shows the parameters available. DIGITAL COMMUNICATIONS LIST ‘comms’ Name Scrolling Display Parameter Description Value I D MODULE IDENTITY Comms identity none No module fitted r232 RS 232 Modbus interface r485 RS485 Modbus interface r422 RS422 Modbus 3216 only dc.ip Remote setpoint input.
PAGE 24
3200 Series 9.3 Modbus Parameter Addresses Parameter Mnemonic Parameter Name Modbus Address PV.IN PV (Temperature) Input Value (see also Modbus address 203 which allows writes over Modbus to this variable). 1 TG.SP Target Setpoint. NB – do not write continuously changing values to this variable. The memory technology used in this product has a limited (100,000) number of write cycles.
PAGE 25
3200 Series Parameter Mnemonic Parameter Name Modbus Address 8 – Target setpoint 9 – No PV 10 – PV is not displayed when controller in Standby - Instrument version number. Should be read as a hexadecimal number, for example a value of 0111 hex is instrument V1.11 107 ADDR Instrument Comms Address 131 9.4 SPI Parameter Addresses This instrument variant supports the following SPI Device types (no configuration is required, the devices automatically respond to requests made to these device types).
PAGE 26
3200 Series SETPOINT PROCESS TEMPERATURE POLL: 20 30 SELECT: 20 31 FORMAT: Numeric UNITS: ºF DESCRIPTION: Temperature at which the process is to be maintained. ALARM, HIGH TEMPERATURE DEVIATION POLL: 20 32 SELECT: 20 33 FORMAT: Numeric UNITS: ºF DESCRIPTION: This Value in conjunction with the process setpoint determines at what temperature the high alarm will occur. It must always be positive.
PAGE 27
3200 Series STATUS PROCESS POLL: 20 40 SELECT: N/A FORMAT: 16 Bits UNITS: None DESCRIPTION: 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Processing Alarm, System Alarm, Process N/A Alarm, High Temp Alarm, Low Temp N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 9.5.2 PROCESSI NG BIT#: 0 DESCRIPTION: This status bit states whether this unit is currently processing.
PAGE 28
3200 Series ALARM, HIGH TEMPERATURE BIT#: 4 DESCRIPTION: This status bit states the temperature controller has exceeded its over setpoint deviation. This assumes the 3200 has been set up such that the first configured alarm (e.g. Alarm 2 if Alarm 1 is not configured) is a high alarm. ALARM, LOW TEMPERATURE BIT#: 5 DESCRIPTION: This status bit states the temperature controller has exceeded its below setpoint deviation. This assumes the 3200 has been set up such that the second configured alarm (e.g.
PAGE 29
3200 Series DESCRIPTION: This status bit states whether this unit is currently processing. 0 = not currently processing (3200 manual mode) 1 = processing (3200 auto mode) ALARM, SYSTEM BIT#: 1 DESCRIPTION: This status bit states an alarm is present. In the 3200, this is set if any of the 4 temperature alarms are set, or if Sensor Break, Span Error, or Loop break is set. ALARM, PROCESS BIT# 2 DESCRIPTION: This bit indicates that an alarm that affects the process has occurred.
PAGE 30
3200 Series 9.6 DEVID 26 & 27 The 3200 uses a single zone only (31). Self Tuning General Purpose Temperature Controllers and General Purpose Temperature Controls support the following set of parameters. 9.6.1 ECHO POLL: 20 20 SELECT: 20 21 FORMAT: Open – 4 Bytes UNITS: ASCII DESCRIPTION: Controller integrity command. Controller will accept and retain the data provided. The controller will provide the retained data in response to a poll enquiry.
PAGE 31
3200 Series PROPORTIONAL BAND 1 POLL: 31 24 SELECT: 31 25 FORMAT: Numeric UNITS: ºF DESCRIPTION: Proportional band for the primary control output in degrees RESET 1 (INTEGRAL) POLL: 31 28 SELECT: 32 29 FORMAT: Numeric UNITS: Seconds DESCRIPTION: Reset time for the primary control output in seconds (Integral term). RATE 1 (DERIVATIVE) POLL: 31 2A SELECT: 32 2B FORMAT: Numeric UNITS: Seconds DESCRIPTION: Rate time for the primary control output in seconds (Derivative term).
PAGE 32
00 Series ALARM 1 RESET POLL: N/A SELECT: 31 35 FORMAT: Status UNITS: None DESCRIPTION: Write a value of 1 to acknowledge alarm conditions. Note that in the 3200, all alarms are acknowledged when this parameter is written to. ALARM 2 RESET POLL: N/A SELECT: 31 37 FORMAT: Status UNITS: None DESCRIPTION: Write a value of 1 to acknowledge alarm conditions. Note that in the 3200, all alarms are acknowledged when this parameter is written to.
PAGE 33
3200 Series CONTROLLER STATUS POLL: 31 44 SELECT: N/A FORMAT: Status UNITS: None DESCRIPTION: Instrument status. 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 N/A N/A Manual Control Low Alarm 1 High Alarm 1 N/A N/A Open TC Alarm N/A Shorted TC Alarm N/A N/A N/A N/A N/A Process Out of Cont. PROCESSING BIT#: 0 DESCRIPTION: This status bit states whether this unit is currently processing.
PAGE 34
3200 Series DESCRIPTION: Indicates that the second configured 3200 alarm is active. For example if Alarm 1 is not configured, Alarm 2 is set to be an absolute low alarm, and Alarm 3 is set to be an absolute high alarm, this bit will be set if the temperature is higher than alarm setpoint 3.
PAGE 35
3200 Series AUTOTUNE RATE 1 (DERIVATIVE) POLL: 31 4E SELECT: 32 4F FORMAT: Numeric UNITS: Seconds DESCRIPTION: Autotune control rate time in seconds (Derivative term). Same as “Rate 1” in 3200. AUTOTUNE CONTROLS POLL: N/A SELECT: 31 55 FORMAT: Status UNITS: None DESCRIPTION: Clear autotune parameters and begin autotune.
PAGE 36
3200 Series PROCESS TEMPERATURE DEVIATION POLL: 31 AA SELECT: N/A FORMAT: Numeric UNITS: ºF DESCRIPTION: Plus or minus temperature deviation from setpoint in degrees. 10. Remote Setpoint (Optional) There are two inputs; 4-20mA and Volts which can be fitted in place of digital communications. It is not necessary to fit an external burden resistor to the 4-20mA input. If the 4-20mA remote setpoint input is connected and valid (>3.5mA; < 22mA) it will be used as the main setpoint.
PAGE 37
3200 Series 11. Appendix A - Technical Specifications Analogue Input Sample rate Calibration accuracy Resolution Linearisation accuracy Input filter Zero offset Thermocouple Types Cold junction compensation CJC Calibration accuracy RTD/PT100 Type Bulb current Lead compensation Process Linear Current transformer Fusing 4Hz (250mS) +0.25% of reading +1LSD <5, 0.5µV when using a 5 second filter <0.1% of reading Off to 59.
PAGE 38
3200 Series Input current Scale Input impedance Accuracy Alarms Indication Types 0 to 50mA rms calibrated, 50/60Hz 0 to 10, 25, 50 or 100Amps <20Ω +4% of reading Leakage current, overcurrent Custom scrolling message and beacon High, low, deviation band, sensor fault, load leakage current, over current, internal events Recipes Number Parameters stored Selection 5 38 Key press or via remote communications Text Messages Dimensions and weight Power Supply Temperature and RH Storage temperature Panel seali
PAGE 39
3200 Series 12. Appendix B - ACS Custom Configuration Parameter List 12.1.1 Water Temp Unit • ACS #: 724.00756.02 • Recipe Name: WAT 12.1.2 Hot Oil Unit • ACS #: 724.00756.02 • Recipe Name: OIL 12.1.3 One Compressor Chiller – New (Effective (09/07) • ACS #: 724.00756.02 • Recipe Name: 1CHL 12.1.4 Two Compressor Chiller – New (Effective 09/07) • ACS #: 724.00756.02 • Recipe Name: 2CHL 12.1.5 One Compressor Chiller – Retrofit • ACS #: 724.00789.02 • Recipe Name: 1CHR 12.1.
PAGE 40
3200 Series 40 ACS 3216 Operators Manual
PAGE 41
Water (TCU) ACS#: 724.00756.02 Recipe Name: WAT Input IO - 1 Config Config OP - 2 Config AA Config SP Config CTRL Config 1KrT rELY rELY rELY IN.TYP 1.ID 2.ID 4.TYPE SP.SEL COOL 1 FUNC HEAt 2 FUNC d.out 4.FUNC SP1 o F UNITS nnnn DEC.P SP1 t.run 4.SRC.A SP2 nor 1.SENS nor 2.SENS nonE 4.SRC.B SP.HI -328 RNG.LO nonE 4.SRC.C SP.LO 0.0 PV.OFS nonE 4.SRC.D RM.SP on SB.TYP nor 4.SENS 9999 rev 0 8 38 TI 1.0 m ln RAMPU R2G 0 d.hi 0.0 OFF 2 EVT no d.hi 100.
PAGE 42
Hot Oil ACS#: 724.00756.02 Recipe Name: Oil Input IO - 1 Config Config OP - 2 Config AA Config SP Config CTRL Config 1KrT rELY rELY rELY IN.TYP 1.ID 2.ID 4.TYPE SP.SEL COOL 1 FUNC HEAt 2 FUNC d.out 4.FUNC SP1 o F UNITS nnnn DEC.P SP1 t.run 4.SRC.A SP2 nor 1.SENS nor 2.SENS nonE 4.SRC.B SP.HI -328 RNG.LO nonE 4.SRC.C SP.LO 0.0 PV.OFS nonE 4.SRC.D RM.SP on SB.TYP nor 4.SENS nonE Pid CTRL.C 2.00 2.PLS 1.6 FIL.T Pid CTRL.H 175 2.00 1.PLS 1202 RNG.
PAGE 43
1 Compressor Chiller - New ACS#: 724.00756.02 Recipe Name: 1CHL Input IO - 1 Config Config OP - 2 Config AA Config LA Config CT.INP Config SP Config CTRL Config K TC rELY rELY rELY L.IP CT.ln IN.TYP 1.ID 2.ID 4.TYPE L.TYPE CT.ID SP.SEL D.OUT 1 FUNC HEAt 2 FUNC d.out 4.FUNC SP2 L.D.IN nonE CT.SRC SP1 1.DHI 1.srC.A 2.00 2.PLS 2.dlo 4.SRC.A NOR L.SENS CT,RNG SP2 1202 RNG.HI nonE 1.srC.B nor 2.SENS nonE 4.SRC.B nonE CT.LAT SP.HI -328 RNG.LO NONE 1.srC.C nonE 4.SRC.
PAGE 44
2 Compressor Chiller - New ACS#: 724.00756.02 Recipe Name: 2CHL Input IO - 1 Config Config OP - 2 Config AA Config LA Config CT.INP Config SP Config CTRL Config K TC rELY rELY rELY L.IP CT.ln IN.TYP 1.ID 2.ID 4.TYPE L.TYPE CT.ID SP.SEL D.OUT 1 FUNC HEAt 2 FUNC d.out 4.FUNC SP2 L.D.IN nonE CT.SRC SP1 3.DHI 1.srC.A 2.00 2.PLS 4.dhi 4.SRC.A NOR L.SENS CT,RNG SP2 1202 RNG.HI nonE 1.srC.B nor 2.SENS nonE 4.SRC.B nonE CT.LAT SP.HI -328 RNG.LO NONE 1.srC.C nonE 4.SRC.
PAGE 45
1 Compressor Chiller - Retrofit ACS#: 724.00789.02 Recipe Name: 1CHR Input IO - 1 Config Config OP - 2 Config AA Config SP Config CTRL Config K TC rELY rELY rELY IN.TYP 1.ID 2.ID 4.TYPE SP.SEL D.OUT 1 FUNC HEAt 2 FUNC d.out 4.FUNC SP1 o F UNITS nnnn DEC.P SP1 2.dlo 4.SRC.A SP2 1202 RNG.HI NONE 1.srC.B nor 2.SENS nonE 4.SRC.B SP.HI -328 RNG.LO NONE 1.srC.C nonE 4.SRC.C SP.LO 0.0 PV.OFS NONE 1.srC.D nonE 4.SRC.D RM.SP 1.6 FIL.T 2.00 1.PLS on SB.TYP nor 1.SENS 87.0 pv.
PAGE 46
2 Compressor Chiller - Retrofit ACS#: 724.00789.02 Recipe Name: 2CHR Input IO - 1 OP - 2 Config Config Config AA Config SP Config CTRL Config K TC rELY rELY rELY IN.TYP 1.ID 2.ID 4.TYPE SP.SEL HEAT 1 FUNC D.OUT 2 FUNC d.out 4.FUNC SP1 o F UNITS nnnn DEC.P SP1 4.DHI 4.SRC.A SP2 nor 1.SENS NONE 2.srC.B nonE 4.SRC.B SP.HI -328 RNG.LO NONE 2.srC.C nonE 4.SRC.C SP.LO 0.0 PV.OFS NONE 2.srC.D nonE 4.SRC.D RM.SP 1.6 FIL.T nor 2.SENS 4 18 TI 1 TD 87.0 0 LOC.