User Guide

ManualsBrandsACT ManualsOtherACTPRO MIFARE PRODUCT RANGE

ACTpro mifare 1050 Pin and Proximity Reader (Entry)

ACTpro mifare 1040 Proximity Reader (Exit)

Controller

SENSE

CLOCK

DATA

+5V

RED

GREEN

CARD/PROX READER

2 31

5 64

8 97

White

Green

Blue

Red

Black

Brown

Yellow

Orange

No Connect

No Connect

SENSE

CLOCK / D1

DATA / D0

12V

RED

GREEN

BUZZER

 A

 B

Wiring for Reader

The standard wiring colours for

ACTpro proximity and pin readers

is shown above.

125VAC

30VDC

+12V

Data

Clock

Sense

R ed

Grn

B uzz

Connection block view of ACTpro mifare 1040/1050.

U nit C1, S outh City B usiness Center, T allaght, Dublin 24, Ireland.

Telephone: +353 1 466 2570. T elefax: 353 1 452 0427. E -m ail: sales@ accesscontrol.ie W eb: www.access control.ie

Wiring for Entry/Exit Readers

ACTpro mifare product range

1040/1050

ACT

mifare

ACT

mifare

+12v

General Wiring information

READER MUST BE POWERED FROM 12vDC

ACTpro mifare

1040

Sector

No: 00005

Test

Powering on the reader requires 12V and 0V

to be Connected.

Data read from a card is presented on the

Data/Clock pins. If configured for wiegand

output the D0 signal is available on Data and D1

is available on Clock.

The Sense signal is driven low when the

reader outputs Clock and Data information, this

can be used to distinguish between Entry and

Exit (see below)

The Internal buzzer is activated by applying

0V to the Buzz. The buzzer activates 4 seconds

after the 0V is applied and sounds continuously

till the 0V is removed.

The Red/Green led is activated by applying

0V to the respective Red/Grn input.

READER MUST BE POWERED FROM 12vDC

To make a reader an exit reader leave the Sense line unconnected.

To make a reader an entry reader ensure the Sense line is connected.

Rev 1.3 27/04/2007

+12v

PAGE 1

Summary of content (4 pages)

PAGE 1
ACTpro mifare product range 1040/1050 Rev 1.3 27/04/2007 General Wiring information Connection block view of ACTpro mifare 1040/1050. Wiring for Reader ACTpro mifare 1040 Sector No: 00005 125V AC 30V DC Powering on the reader requires 12V and 0V to be Connected. White SENSE Green CLOCK / D1 Blue DATA / D0 Red 12V Black 0V Brown RED Yellow GREEN Orange BUZZER No Connect A No Connect B Test Data read from a card is presented on the Data/Clock pins.
PAGE 2
ACTpro mifare product range 1040/1050 Reader Configuration OUTPUT DATA FORMAT Clock and Data Default Output Format is Clock and Data (also know as Magnetic Stripe Track/2 or ABA). Using this default format the data is encoded as 10 BCD digits . Wiegand The reader can be configure to output the data in wiegand format instead of clock and data. Connecting the Sense line to OV before powering on the reader will switch the unit to wiegand output mode. The reader will output 37 bit wiegand.
PAGE 3
ACTpro mifare product range 1040/1050 Power On Beep Codes The Output Data Format and the Sector/Serial Operation of the reader can be determined by the beeps generated by the reader after power is applied. The reader will generate two sets of beeps, the first indicating the Output Data Format and the second set of beeps indicates Sector or Serial Operation. The first set of beeps will occur while the Led is Green, the second set of beeps occur half a second later while the Led is Blue.
PAGE 4
Mounting Instructions for Flush Mount Unit Spacers break away from main component when required by installer for use. View showing spacers stacking View showing mounting plate before spacers are broken away by installer. Note: Determine the distance between the patress box and the mounting plate, using the spacers that are labelled 1mm to 4mm. A spacer of the correct length is assembled by stacking the spacers together. Screws Standard pattress box.