HK-II Terminal User’s Guide
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the Installation Manual, may cause harmful interference to radio communications.
Table of Contents Introduction 3 HandKey II Biometrics Principle of Operation The HandKey II Specifications Options UL Compliance 3 3 3 3 5 6 6 Planning an Installation 7 Site Preparation HandReader Placement Wiring Power Input Battery Backup Earth Ground and Shielding Earth Ground All Units Carry a Ground Line to Each Unit Door Control Output Lock Output Mode Card Reader Emulation Mode Inputs and Outputs 7 7 8 8 8 9 10 11 12 12 12 12 Networking and Communications 15 Stand-alone HandReader Master
Wiring Connections 21 Wiring Connections 21 Wiring Examples 21 Erasing the Memory 31 Erasing HandReader Memory 31 Enter a Command Menu 33 If No One is Enrolled in the HandReader If Users are Enrolled in the HandReader Navigating Command Menus 33 34 34 Programming the HandReader 35 Authority Level Programming Order System Management and Maintenance Design an ID Numbering System 36 36 37 37 Service Menu 39 Navigating the Service Menu Service Commands Calibrate Status Display Network Status
HandKey II Manual Data From Network Data To Network 48 48 Enrollment Menu 49 Preparation User Education Proper Hand Placement Left Hand Enrollment Read Score Navigating the Enrollment Menu Enrollment Commands Add User Remove User 49 50 50 50 51 51 51 51 51 Security Menu 53 Navigating the Security Menu Security Commands Set User Data Set TZ Table Reject Threshold Set Passwords Clear Memory Special Enroll 53 53 55 55 56 56 56 56 HandReader Maintenance 57 Cleaning the Hand Reader User Score 57 57
Appendix D: Troubleshooting Guide 79 Erasing the HandReader Setup and User Database 77 Appendix D: Troubleshooting Guide 79 Display Messages During Verification Beeper and LED Status During Verification 79 80 Glossary 81 Limited Warranty 83 vi
Introduction HandKey II The HandKey II is Schlage Biometrics’ fourth generation biometric access control HandReader1. The HandReader records and stores the three-dimensional shape of the human hand for comparison and identity verification. Upon verification, the HandReader produces an output that can unlock a door, send card format data to an access control panel, or communicate with a host computer.
Introduction HAND PLACEMENT DISPLAY VERIFICATION LIGHTS LCD DISPLAY Recog nition NUMERICAL KEYPAD 1 4 7 * No 8 0 2 3 5 Ente r Clea F1 F2 # Nos Ye s Inc. r 6 9 System FUNCTION KEYS PLATEN AND GUIDE PINS Figure 3-1: The HandKey II The HandReader has an integrated keypad for ID entry and reader programming. It has two function keys (F1 and F2) that can be set to activate external devices such as a doorbell or an automatic door.
HandKey II Manual Specifications Size: 8.85 inches wide by 11.65 inches high by 8.55 inches deep (22.3 cm) 22.3 cm wide by 29.6 cm high by 21.7 cm deep Power: 12 to 24 VDC or 12 to 24 VAC 50-60 Hz, 7 watts Weight: 6 lbs (2.
Introduction Options HandKey units have the following options available. • Backup Battery Support See Technical Note 70200-0012 rev C • Modem Communication See Technical Note 70200-0013 rev C • Ethernet Communication See Technical Note 70200-0014 rev H UL Compliance Hand Readers are UL Listed as stand alone units only (i.e. the card reader function has not been evaluated by UL). The HandKey ll has not been tested for UL 294 in an Outdoor configuration.
Planning an Installation Site Preparation Before you begin installation, check the site blueprints, riser diagrams, and specifications for important information about the HandRreader’s location and other systems that will connect to the HandReader. Look for any existing wall preparations and wiring that other contractors may have installed for the HandReaders. HandReader Placement The recommended height for the HandReader platen is 40 inches (102 cm) from the finished floor.
Planning an Installation Wiring Four basic circuits typically connect to the HandReader: • Power Input • Door Control Inputs and Outputs • Networking and Communications • Card Reader Input and Emulation Output Power Input The HandReader requires 12 to 24 volts DC (600 mA) or 12 to 24 volts AC (7 watts). Power can be connected either to the power terminal pins 1 and 2 or through barrel jack J12. 1 and the center pin of power jack J12 are connected together.
HandKey II Manual two pins protruding up from the main logic board are not connected to each other. This effectively opens the circuit, removing the battery from any internal circuitry. Main input power can then be removed and the HandReader will fully shut down. Once the HandReader has fully shut down, shunt J7 may be reinstalled. The design of the power supply is such that main input power must be reapplied to re-enable the battery protection mechanism.
Planning an Installation 14 13 12 11 10 9 8 7 6 5 4 3 2 1 CARD READER INPUT SWITCH INPUTS OUTPUTS AUX IN 2 AUX IN 1 GROUND GROUND DOOR SWITCH REX SWITCH AUXOUT 2 AUXOUT 1 LOCK OR CLOCK BELL OR DATA GROUND CLOCK/D1 DATA/D0 +5 VDC OUTPUT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 EARTH GROUND CONNECTION PINS Figure 4-2: Earth Ground Connection Terminals There are two standard methods for providing earth grounding to HandKey units: • earth grounding all units (see figure 4-3 on page 11) • carrying
HandKey II Manual For systems with multiple units on a network, there will be a series of cables daisychained between the units, and the shield of each leg of the network should be connected to ground at only one end. It does not matter which end. An example of this method of grounding is shown in Figure 2-3.
Planning an Installation However, the power supplies must be truly floating, with no hidden paths back to the high-voltage side of the transformers, or to earth ground. Since this is difficult to achieve (there is always some parasitic capacitance between the primary and secondary in any transformer), this method may be more susceptible to high-frequency transients in the high-voltage side of the power lines than the earth-grounded method.
HandKey II Manual An open collector transistor driver drives each one of these outputs. Open collector refers to a transistor configuration capable of sinking current (by “pulling down” one side of a load to ground) but not able to source current – e.g. the transistor output is incapable of supplying current to drive up the output voltage and must rely on an external voltage source to accomplish this. HandReader outputs, when measured to ground, generally show around 4.
Planning an Installation 14
Networking and Communications HandReader networking and communications can be configured in one of five ways: • as a stand-alone HandReader • as a master or remote HandReader in a HandReader network • as a remote HandReader in a HandReader network connected to a host PC • as a remote network connected via optional Modem to host PC • as a remote network connected via optional Ethernet to host PC Stand-alone HandReader When installed as a stand-alone access control system there is no communication wiring to
Networking and Communications Typically, HandReader networks link to a PC using an RS-422 connection. These networks have the following requirements. • Two twisted pair, shielded, AWG 22 wire or larger should be used (Schlage Biometrics recommends Belden No. 82723 or equivalent cable). • HandReaders must be wired together in a “daisy chain” network from HandReader to HandReader and then to the host PC. The total length of the wiring must not exceed 4,000 feet per network.
Mechanical Installation Select an installation location based on the guidelines provided in the Planning an Installation section beginning on page 7. Wall Plate Installation the following instructions protect the HandReader from the dust and debris generated ! NOTE For during the wall plate installation process. 1. Remove the wall plate from the packing carton. Refer to Figure 4-1 for all wall plate references in the following section. HOLE 2 UPPER SCREWS SURFACE CONDUIT ENTRY Figure 6-2: Wall Plate 3.
Mechanical Installation 5. For a solid wall, hold the wall plate against the wall, centering the leveling hole over the mark in the wall. 6. Align a bubble level with the top edge of the wall plate and gently rotate the wall plate until the bubble level shows that the top edge of the wall plate is level. 7. Secure the plate to the wall using heavy masking tape. 8. Using the wall plate as a template, mark the locations of the two upper screw holes and the three lower screw holes. 9.
HandKey II Manual Attaching the HandReader 1. Remove the HandReader from its carton. 2. Align the sleeves of the back plate with the pins of the wall plate and slide the HandReader to the left as shown in figure 4-2. HOLE 2 UPPER SCREWS SURFACE CONDUIT ENTRY REAR OF TERMINAL Figure 6-3: Attaching the HandReader to the Wall Plate 4. The HandReader is now ready for its wiring connections.
Mechanical Installation Closing the HandReader With the wall mount latch in the unlocked position, swing the body of the HandReader up and rotate the key away from the wall. Hold the top of the HandReader firmly against the wall and rotate key towards wall, locking the latch into place (see Figure 4-3). not force the HandReader onto the wall mount latch when the latch is in the locked ! NOTE Do (down) position. Wall Plate S metsy .
Wiring Connections Once the HandReader is attached to the wall plate the wiring connections to the HandReader can be made (see Figure 5-1). WALL Power Connectors Terminal Strips Reset J7 Battery Switch Jumper Wall Plate Optional Modem Serial RS-232 or Ethernet Top of Terminal Top of HandKey Figure 7-1: Wiring Connections Wiring Examples The following Tables provide the pin outs for the terminal strips on the HandReader.
Wiring Connections Table 7-1: TS-1 - Power and Communication Connections Terminal Connection 15 RS-422 Rx- or RS-485 Rx-/Tx- 16 RS-422 Tx- or RS-485 Rx+/Tx+ 17 RS-422 Rx+ 18 RS-422 Tx+ Table 7-2: TS-2 - Input Connections Terminal Connection 9 10 11 12 13 14 Request to Exit Input Ground Door Monitor Switch Input (NC Standby) Auxiliary Input 1 Ground Auxiliary Input 2 Table 7-3: TS-3 - Output Connections Terminal Connection 1 2 3 4 5 6 7 8 +5 VDC @ 400mA Max.
HandKey II Manual * POWER SUPPLY +12 to 24 VDC Max + NC AUX OUTPUT 2 AUX OUTPUT 1 AUX OUTPUT 0 REQUEST TO EXIT N.C. DOOR SWITCH* AUX INPUT 1** N.O. DOOR SWITCH N.O. MOMENTARY* AUX INPUT 2** SWITCH LEGEND *ELECTRIC LOCK + OR STRIKE - NO *LOCK RELAY WALL TO WHICH THE HAND READER IS ATTACHED HINGE 12 to 24 V AC/DC Input 1 2 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 RS-422 Connection TOP OF THE HAND READER * These components are not supplied by Schlage Biometrics, Inc.
Wiring Connections * POWER SUPPLY +12 to 24 VDC Max + NC NO + AUX OUTPUT 2 AUX OUTPUT 1 AUX OUTPUT 0 N.C. DOOR SWITCH* REQUEST TO EXIT N.O. MOMENTARY* AUX INPUT 1** N.O. DOOR SWITCH SWITCH LEGEND AUX INPUT 2** *AUX RELAY *AUXILIARY DEVICE WALL TO WHICH THE HAND READER IS ATTACHED HINGE 12 to 24 V AC/DC Input 1 2 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 RS-422 Connection TOP OF THE HAND READER * These components are not supplied by Schlage Biometrics, Inc.
HandKey II Manual Card Reader GROUND DATA 1 DATA 0 +5 VDC POWER (SEE NOTE BELOW) Access Panel GROUND DATA 1 DATA 0 WALL TO WHICH THE HAND READER IS ATTACHED HINGE 12 to 24 V AC/DC Input 1 2 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 RS-422 Connection TOP OF THE HAND READER NOTE: For +12 VDC readers, connect power supply +12 VDC to card reader.
Wiring Connections 1 4 7 * No 2 5 8 3 6 9 0 Clear F1 F2 # No Yes Enter TS-1 Rx - 15 4-Wire RS-422 Connection Master 1 4 7 * No 2 5 8 3 6 9 0 Tx - 17 Tx + 18 Clear F1 F2 # No Yes Rx + 16 Enter TS-1 4-Wire RS-422 Connection Rx - 15 Rx + 16 Tx - 17 Tx + 18 Remote 1 1 4 7 * No 2 5 8 0 3 6 9 Clear F1 F2 # No Yes Enter TS-1 4-Wire RS-422 Connection Rx - 15 Rx + 16 Tx - 17 Tx + 18 Remote X Figure 7-5: RS-422 4-Wire Master/Remote Network System Wiring Diagram 26
HandKey II Manual 1 4 7 * No 2 5 8 3 6 9 0 Clear F1 F2 # No Yes Enter TS-1 2-Wire RS-485 Connection Rx/Tx - 15 Rx/Tx + 16 17 18 Master 1 4 7 * No 2 5 8 3 6 9 0 Clear F1 F2 # No Yes Enter TS-1 Rx/Tx 2-Wire Rx/Tx + RS-485 Connection 15 16 17 18 Remote 1 1 4 7 * No 2 5 8 0 3 6 9 Clear F1 F2 # No Yes Enter TS-1 Rx/Tx 2-Wire Rx/Tx + RS-485 Connection 15 16 17 18 Remote X Figure 7-6: RS-485 2-Wire Master/Remote Network System Wiring Diagram 27
Wiring Connections DC-102 Power Supply RS-232 to 4-wire RS-422 Data Converter (P/N DC-102) Tx+ 1 Tx- 2 Rx- 3 Rx+ 4 DB-25 Serial Port 1 2 4 5 7 8 * No 0 3 6 9 Clear F1 F2 # No Yes Enter TS-1 RS-422 Connection Rx - 15 Rx + 16 Tx - 17 Tx + 18 Remote 1 4 7 * No 2 5 8 3 6 9 0 Clear F1 F2 # No Yes Enter TS-1 Rx - 15 RS-422 Connection Rx + 16 Tx - 17 Tx + 18 Remote 1 4 7 * No 2 5 8 0 3 6 9 Clear F1 F2 # No Yes Enter TS-1 RS-422 Connection Rx - 15 Rx + 16 Tx
HandKey II Manual *Serial Printer WALL TO WHICH THE HAND READER IS ATTACHED HINGE 12 to 24 V AC/DC Input 1 2 4 Pin Connector 18 17 16 15 14 13 12 11 10 9 RS-422 Connection 8 7 6 5 4 3 2 1 J4 RS-232 Jack TOP OF THE HAND READER * These components are not supplied by Schlage Biometrics, Inc. Figure 7-8: Printer to HandKey II Wiring Diagram All HandReaders in a network must be set to the same communication method.
Wiring Connections 30
Erasing the Memory There are two options when erasing the memory of the HandReader. 1. Setup 2. All The erasing of the setup will set the HandReader’s address, passwords, etc. back to factory defaults. Choosing the All option will take the HandReader’s setup back to factory defaults plus erase all user databases and datalogs. This action can not be undone. If there is a software that is managing the system then the users can be downloaded back to the HandReader if needed.
Erasing the Memory 32
Enter a Command Menu Press the If No One is Enrolled in the HandReader Clear and Enter keys simultaneously to enter a command menu. 1. The display appears as follows. ENTER PASSWORD 2. Press the default password for the menu you wish to enter. Press 1 for the Service Menu. Press 2 for the Setup Menu. Press 3 for the Management Menu. Press 4 for the Enrollment Menu. Press 5 for the Security Menu. 3. Press Enter and the first command option in the selected menu appears.
Enter a Command Menu If Users are Enrolled in the HandReader 1. The display appears as follows. ENTER PASSWORD 2. Enter your ID number on the keypad and place your hand on the platen for verification. 3. If verification is successful, the display appears as follows. 4. Enter the password for the menu you wish to enter. The default passwords are as follows. Press 1 for the Service Menu. Press 2 for the Setup Menu. Press 3 for the Management Menu. Press 4 for the Enrollment Menu.
Programming the HandReader The HandReader is programmed via a series of command menus. A summary of the menus and commands is given in Table 6.
Programming the HandReader Authority Level A second method for controlling access to the command menus is through the use of Authority Levels. Authority Levels control which command menus a user is allowed to access; the higher the authority level a user is granted, the greater the number of menus the user may access. Assign Authority Levels to users according to the types of tasks to which they are assigned. • Level 0 is for a user who does not need access to any of the command menus.
HandKey II Manual System Management and Maintenance Once a HandReader network is in operation the following commands are used to manage and maintain the HandReader network. 1. Set Reader Operating Thresholds – Set the Reject and Number-of-Tries HandReader operating thresholds to meet the site’s security requirements. This is done through the Security Menu. 2. System Management – Backup or Restore HandReader data and List the Users authorized to use a HandReader. This is done through the Management Menu.
Programming the HandReader 38
Service Menu The Service Menu commands provide information that helps you determine if the HandReader is operating properly and within normal operating parameters. Navigating the Service Menu Once you have entered the Service menu, there are three options available for navigating the command menu system. • Press # Yes to enter the command shown on the display. • Press * No to step to the next command in the menu.
Service Menu Calibrate The Calibrate command verify that the HandReader’s exposure values are within normal operating parameters. The normal operating parameters are shown in Table 2. Table 11-7: Normal Operating Parameters Status Display Parameter Normal Range Row “r” Column “c” Exposure 0 +/- 2 0 +/- 2 100 +/- 20 The status display command allows you to enable or disable the displaying of the following information.
Setup Menu The Setup menu commands allow you to set the basic operating parameters for the HandReader. in the Setup menu you can step through and set the parameters for each command ! NOTE Once sequentially. You do not have to exit command mode after setting any individual command. Navigating the Setup Menu Once you have entered the Setup menu, there are three options available for navigating the command menu system. Press # Yes to enter the command shown on the display.
Setup Menu Table 12-8: Setup Command Menu Setup Menu Password = 2 Set Language Select Language Set Date Format Select Date Format Set Time and Date Month (MM) Day (DD) Year (YY) Hour (HH) Minute (MM) Set Address New Address Set ID Length New ID Length Set Facility Auxiliary Output Control Select Auxiliary Output 1/2 Aux 1 Out Control Aux 2 Out Control Output Set by Tamper Output Set by ID Refused Output Set by Duress Output Set by Try Again Output Set by F1 Key Output Set by F2 Key Output Set on Battery Bac
HandKey II Manual Set Language The Set Language command allows the language shown on the HandReader’s display to be “localized” for a variety of countries. The default language is English. The following languages are available. English French German Indonesian Italian Set Date Format Japanese Polish Portuguese Russian Spanish The Set Date Format command allows the date format shown on the HandReader’s display to be “localized” for a variety of countries. The default date format is the U.S.
Setup Menu Set the ID Length to the number of digits in the longest ID number. This command is unnecessary (and should be left at its default value) if ID entry is made from a card reader. The ID Length should not be set if a Duress Code is being assigned (see page 49). The default value for ID Length is 10. assigned ID numbers shorter than the number of digits in the longest ID number ! NOTE Users must press following their ID entry to indicate the complete entry has been made.
HandKey II Manual In HandReader networks, one HandReader must be set as a Master HandReader and all remaining HandReaders must be set as Remote HandReaders. The default Reader Mode is Remote mode. Reader Mode does not apply to stand-alone HandReaders or HandReaders in a PC network (the HandReader should be left in its default value). remote HandReaders on a HandReader network must have a unique address. Refer ! NOTE All to the Set Reader Address section on page 43.
46
Management Menu The Management menu commands allow you to manage employee data stored in a HandReader. Navigating the Management Menu Once you have entered the Management menu, there are three options available for navigating the command menu system. • Press # Yes to enter the command shown on the display. • Press * No to step to the next command in the menu. • Press Clear to exit the command menu (pressing any numeric key also exits the command menu).
Management Menu Data From Network The Data from Network command allows the master HandReader to receive information from a HandReader on the network. This is used to transmit user enrollment and system configuration information from an existing HandReader to the master HandReader. Data To Network The Data to Network command transmits all data held by the master HandReader to all HandReaders connected to the network.
Enrollment Menu Enrollment is the process of recording a hand image and associating it with an ID number. The first person to enroll in the HandReader has access to all command menus. This person should be considered the System Administrator and should retain the highest authority level to access all five menus at any time.1 As other users are enrolled they can be left as basic access users or they can be assigned varying degrees of authority depending upon the tasks for which they will be responsible.
Enrollment Menu User Education The HandReader is easy to use and non-threatening. However, most people have never used a biometric HandReader. Training users on how the HandReader works and how to use it will eliminate most fears and concerns before they occur. Inform the users of these facts. • The HandReader reads the shape of the hand, not the fingerprints or palmprints. • It does not identify people. It confirms people’s identity.
HandKey II Manual Read Score When a user uses the HandReader a number appears in the display. ID VERIFIED ## The number on the display reflects how accurately the user is placing his/her hand on the platen. Scores that vary greatly between low and high numbers are indicative of inconsistent hand placement. Scores above 50 are indicative of improper hand placement or of a drastic change in the physical appearance of the hand.
52
Security Menu The commands in the Security menu control the security of the information within the HandReader and the sensitivity of the HandReader when reading hands. Navigating the Security Menu Once you have entered the Security menu, there are three options available for navigating the command menu system. Press # Yes to enter the command shown on the display. Press * No to step to the next command in the menu.
Security Menu Table 15-12: Security Command Menu Security Menu Password = 5 Set User Data Set User Authority Level (Y/N) ID # Authority Level Set User Reject Level ID # Reject at # Set User Time Zone ID # New Time Zone? Edit Time Zone Time Zone # Time Zone Data Print Time Zone Clear Time Zone Time Zone # Edit Holidays Enter Month and Day Print Holidays Clear Holidays Holiday Month Set Unlock Time Zone Time Zone # Set Reject Threshold Reject Threshold # # of Tries Set Passwords Security Password Enroll Passw
HandKey II Manual Set User Data The Set User Data command allows you to set the User Authority level, the User Reject Level, and the User Time Zone. • The Authority Level controls which command menus a user is allowed to access; the higher the authority level, the greater the number of menus the user may access. • The User Reject level allows you to set the number of failed hand read attempts for a user before rejecting further attempts by that user.
Security Menu Reject Threshold Use the Reject Threshold command to set the HandReader’s reject sensitivity level applied when reading hand data and to set the number of tries a user is allowed before being rejected by a HandReader. The reject sensitivity level and number of tries are global values.
HandReader Maintenance A minimum amount of system maintenance is required to keep HandReaders fully functional. HandReaders should be cleaned periodically to prevent an accumulation of dust from affecting the HandReader’s readability. User Scores should be reviewed periodically to ensure the HandReader is performing properly. ! NOTE There are NO user serviceable parts inside the HandReader. Once a HandKey system is in operation there are three HandReader commands that can assist with system maintenance.
HandReader Maintenance 58
Appendix A: Tips for a Successful Installation Unless the following tips are followed, the installation runs the risk of having some level of difficulties. These tips come from years of experience with thousands of sites installed around the world. By far the biggest problem tends to be that the HandReader is allowed to get dirty. Think of the HandReader as a camera, because that is exactly what it is. If a user takes a picture with a dirty camera, then what you get is a dirty picture.
Appendix A: Tips for a Successful Installation Enrollment Bad enrollments equal bad verification (meaning scores will be too high). The key to successful verification is education.
Appendix B: Noted Board Configuration Differences Because of Schlage Biometrics’ camera retrofit of the HandReader some changes have been made to the main PCB and they are listed as follows: • Dipswitches have been removed • comm lines are terminated • RS-485 is set by wiring jumpers • memory is reset with a push-button reset and user interface with keypad and LCD • The labeling of the terminal strips have changed. See Figure 16-1 • The configuration of the terminal strips have changed.
Appendix B: Noted Board Configuration Differences Terminal Block Labeling Number 1 2 3* 4* 5* 6* OLD PCB 12-24 VDC (+) OR VAC 12-24 VDC (-) OR VAC RXRX+ TXTX+ 7 8 9 10 11 12 13 14 REX SWITCH GROUND DOOR SWITCH GROUND AUX IN 1 GROUND AUX IN 2 GROUND 15 16 17 18 19 20 21 22 23 24 25 26 (+) 5 VDC OUTPUT DATA/D0 CLOCK/D1 GROUND LOCK OR CLOCK OUTPUT GROUND BELL OR DATA OUTPUT GROUND AUXOUT 1 GROUND AUXOUT 2 GROUND Number 1 2 3 4 5 6 7 8 NEW PCB (+) 5 VDC OUTPUT DATA/D0 CLOCK/D1 GROUND LOCK OR CLOCK OUTP
HandKey II Manual Terminal Block Layout New Board Old Board 1 2 J6 - 2 pin Power connector 15 16 17 18 TS1 - 4 pin Comm connector TS2 7 8 9 10 11 12 13 14 9 10 11 12 13 14 TS2 - 6 pin Input connector TS3 15 16 17 18 19 20 21 22 23 24 25 26 1 2 3 4 5 6 7 8 TS3 - 8 pin Output connector TS1 1 2 3 4 5 6 7 8 Any of the grounds coming off of pins 8, 10, 12, 14, 18, 20, 22, 24, and 26 of the "Old Board" can be tied to pin 4, 10, or 13 on the new board.
Appendix B: Noted Board Configuration Differences Memory Reset 64 1. 2. 3. 4. 5. To reset the memory of the HandReader follow these stepsRemove power and battery jumper, if a back up battery is installed Press down on reset button and apply power Release button Reader will boot to • Press 1 to erase setup i.e. address, outputs, passwords, but retain user database and datalogs • Press 9 to erase everything i.e.
Appendix C: Old Board Configuration Information Wall Plate Installation Attaching the HandReader 1. Loosen the three bottom mounting screws until there is approximately 1/8 inch (3 mm) clearance between the screw head and the wall plate. 2. Remove the HandReader from its carton. 3. At the base of the HandReader is a piano hinge with three keyhole shaped slots that correspond with the three lower mounting screws. Align and hang the HandReader from the three lower mounting screws (see Figure 17-1).
Appendix C: Old Board Configuration Information Wiring Connections Once the Hand Reader is attached to the wall plate the wiring connections to the Hand Reader can be made (see Figure 17-2).
HandKey II Manual 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 CARD READER INPUT 7 SWITCH INPUTS OUTPUTS AUXOUT 2 GROUND AUXOUT 1 GROUND GROUND BELL OR DATA LOCK OR CLOCK GROUND CLOCK INPUT GROUND EARTH GROUND DATA INPUT +5 VDC OUTPUT AUX IN 2 GROUND AUX IN 1 DOOR SWITCH 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 GROUND GROUND 8 GROUND REX SWITCH 7 CONNECTION PINS Figure 19-8: Earth Ground Connection Terminals There are two standard methods for providing earth
Appendix C: Old Board Configuration Information Table 19-13: TS-1 - Power and Communication Connections Terminal 1 2 3 4 5 6 Connection Power Input 12 to 24 VDC/VAC Power Return RS-422 Rx- or RS-485 Rx-/TxRS-422 Tx- or RS-485 Rx+/Tx+ RS-422 Rx+ RS-422 Tx+ Table 19-14: TS-2 - Input Connections Terminal 7 8 9 10 11 12 13 14 Connection Request to Exit Input Ground Door Monitor Switch Input (NC Standby) Ground Auxiliary Input 1 Ground Auxiliary Input 2 Ground Table 19-15: TS-3 - Card Reader and Output Conne
HandKey II Manual * POWER SUPPLY +12 to 24 VDC Max + SWITCH LEGEND REQUEST TO EXIT N.O. DOOR SWITCH AUX OUTPUT 0 AUX OUTPUT 1 AUX OUTPUT 2 *ELECTRIC LOCK + OR STRIKE - AUX INPUT 1 ** NO *LOCK RELAY AUX INPUT 2 ** NC N.O. MOMENTARY* N.C.
Appendix C: Old Board Configuration Information *POWER SUPPLY +12 to 24 VDC Max + SWITCH LEGEND REQUEST TO EXIT N.C. DOOR SWITCH *AUXILIARY DEVICE AUX OUTPUT 0 AUX OUTPUT 1 AUX OUTPUT 2 + AUX INPUT 1 ** NO *AUX. RELAY AUX INPUT 2 ** NC N.O. MOMENTARY* N.C.
HandKey II Manual Card Reader AUX INPUT 1 ** AUX INPUT 2 ** AUX OUTPUT 0 AUX OUTPUT 1 AUX OUTPUT 2 DATA 1 GROUND DATA 0 REQUEST TO EXIT Access Panel N.C. DOOR SWITCH GROUND DATA 1 DATA 0 +5 VDC POWER (SEE NOTE BELOW) SWITCH LEGEND N.O. MOMENTARY* N.C.
Appendix C: Old Board Configuration Information TS-1 3 6 9 Clear 12 to 24 V AC/DC Input F1 F2 # No Yes Enter 4-Wire RS-422 Connection Master 1 4 7 * No 2 5 8 2 Rx - 3 Rx + 4 Tx - 5 Tx + 6 Clear 12 to 24 V AC/DC Input F1 F2 # No Yes 1 - TS-1 3 6 9 0 + 2 5 8 0 Enter 4-Wire RS-422 Connection + 1 4 7 * No 1 - 2 Rx - 3 Rx + 4 Tx - 5 Tx + 6 Remote 1 2 5 8 0 TS-1 3 6 9 Clear F1 F2 # No Yes Enter 12 to 24 V AC/DC Input 4-Wire RS-422 Connection + 1 4 7 *
HandKey II Manual 2 5 8 Clear 12 to 24 V AC/DC Input F1 F2 # No Yes TS-1 3 6 9 0 Enter 2-Wire RS-485 Connection + 1 4 7 * No 1 - 2 Rx/Tx - 3 Rx/Tx + 4 5 6 Master 2 5 8 Clear 12 to 24 V AC/DC Input F1 F2 # No Yes TS-1 3 6 9 0 Enter 2-Wire RS-485 Connection + 1 4 7 * No 1 - 2 Rx/Tx - 3 Rx/Tx + 4 5 6 Remote 1 2 5 8 0 TS-1 3 6 9 Clear F1 F2 # No Yes Enter 12 to 24 V AC/DC Input + 1 4 7 * No 1 - 2 Rx/Tx - 3 2-Wire Rx/Tx + 4 RS-485 5 Connection 6 Rem
Appendix C: Old Board Configuration Information DC-102 Power Supply RS-232 to 4-wire RS-422 Data Converter (P/N DC-102) Tx+ 1 Tx- 2 Rx- 3 Rx+ 4 DB-25 Serial Port Recogn ition System s Inc. 5 7 8 * No 0 TS-1 2 3 6 9 12 to 24 V AC/DC Input Clear F1 F2 # No Yes Enter RS-422 Connection + 1 4 1 - 2 Rx - 3 Rx + 4 Tx - 5 Tx + 6 Remote Recogn ition System s Inc.
HandKey II Manual RJ-45 to Printer Adapter (if required) *Serial Printer WALL TO WHICH THE HAND READER IS ATTACHED RJ-45 Connector HINGE RJ-45 Connector 12 to 24 V AC/DC Input TS-3 TS-2 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 TS-1 9 8 7 6 5 4 3 2 1 - + J4 RJ-45 Jack RS-422 Connection TOP OF THE HAND READER * These components are not supplied by Schlage Biometrics, Inc.
Appendix C: Old Board Configuration Information Setting the DIP Switches DIP Switch settings perform three tasks for the Hand Reader (see Figure 17-11). Set End of Line (EOL) Termination to match the type of termination the network being used needs. • Set the Communication Method to match the type of network used. • Erase Memory to clear Hand Reader memory to all factory default values and also clear all user memory.
HandKey II Manual Communication Method Communication can be done via an RS-232 direct connection, a 4-wire RS-422 network configuration. The factory default setting is for network communication via 4-wire RS-422 cabling – switch 3 OFF. Refer to Figure 17-11 for switch ON/OFF positioning. • For network communication via RS-422 cabling, switch 3 must be OFF. • For network communication via 2-wire RS-485 cabling, switch 3 must be ON.
Appendix C: Old Board Configuration Information Closing the HandReader Before closing the Hand Reader, ensure dip switches 4 and 5 are OFF (refer to Figure 17-11). With the wall mount latch in the unlocked position, swing the body of the Hand Reader up and lock the latch into place with the key provided with the Hand Reader (see Figure 17-12). not force the Hand Reader onto the wall mount latch when the latch is in the locked ! NOTE Do position. Wall Plate S metsy .
Appendix D: Troubleshooting Guide Display Messages During Verification Various messages can appear on the HandPunch’s display during hand verification. These messages are defined in. Table 20-17: Display Messages During Verification Message PLACE HAND ID VERIFIED REMOVE HAND TRY AGAIN ID REFUSED ENTER ID Definition The platen is ready to receive your hand for verification. You are verified, proceed. Remove your hand and place it on the platen again. Follow proper hand placement rules.
Appendix D: Troubleshooting Guide Beeper and LED Status During Verification The HandPunch’s beeper and LED status display also display hand verification information. This information is defined in.
Glossary Address, IP – An Internet Protocol address is a unique address assigned to a computer for communicating over the Internet. It is made up of 4 sets of numbers, separated by periods (for example, 123.245.78.901). Address, Reader – A Hand Reader Address is a unique identification number assigned to a Hand Reader. Each Hand Reader on a network must be assigned a unique address. AWG – American Wire Gauge is a U.S. standard set of wire conductor sizes. The “gauge” refers to the diameter of the wire.
Glossary Transaction – A Transaction is any kind of event recorded at a Hand Reader. Transactions may include actions such as accepted or denied hand reads, input and output events, and doors opening and closing. Wiegand™ Reader – The term “Wiegand Reader” has two meanings depending upon its application. A true Wiegand reader reads a specially constructed card made up of small pieces of magnetic wire. As the card is swiped through the reader, the individual bits of wire generate a unique data signal.
Limited Warranty Schlage Biometrics, Inc.
Ingersoll Rand’s Security Technologies Sector is a leading global provider of products and services that make environments safe, secure, and productive. The Sector’s market-leading products include electronic and biometric access control systems; time and attendance and personnel scheduling systems; mechanical locks and portable security, door closures and exit devices, steel doors and frames, architectural hardware and technologies and services for global security markets. 866.861.
