ACM-3001 IP PoE Fixed Dome Camera Hardware User’s Manual (DC 12V / PoE) Ver.
ACM-3001 Hardware User’s Manual Table of Contents 0. Precautions 3 1. Introduction 4 Package Contents ........................................................................... 4 Features and Benefits ..................................................................... 5 Safety Instructions .......................................................................... 6 Physical description ........................................................................ 8 Installation Procedure ...............
ACM-3001 Hardware User’s Manual 0. Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.
ACM-3001 Hardware User’s Manual 1. Introduction Package Contents ACM-3001 Product CD Warranty Card Accessories Drill Template Drill template 4 www.acti.
ACM-3001 Hardware User’s Manual Features and Benefits This is a cutting-edge digital video surveillance camera. It can compress and transmit real time images with outstanding image quality (30 FPS @ VGA, 640x480) through a standard TCP/IP network. This camera is your best choice to build an intelligent IP surveillance system. MPEG-4/MJPEG Dual Codec Compression This device supports two compression formats, MPEG-4 and MJPEG.
ACM-3001 Hardware User’s Manual Safety Instructions Don’t use the power supply with other voltages This device is likely to be damaged or damage other equipments / personnel, if you use a power supply with different voltage than the one included with this device. All warranty of this product will be voided in the situations above. Cleaning Disconnect this video product from the power supply before cleaning.
ACM-3001 Hardware User’s Manual Safety Check Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine if the video product is in proper operating condition. 7 www.acti.
ACM-3001 Hardware User’s Manual Physical description 1) Ethernet Port The IP PoE Fixed Dome Camera connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this IP PoE Fixed Dome Camera can auto detect the speed of local network segment (10Base-T/100Base-TX Ethernet). 2) Power Input Connect the power adaptor here if your power input is DC12V.
ACM-3001 Hardware User’s Manual Step 2: Press and continue to hold the Reset Button (with a sharp tipped object, like a pen.) Step 3: Reconnect the power cable while continuing to hold the reset button. The red Power LED light will flash on for 3 second first, turn off for about 15 seconds, flash on for another second and turn off again. By this time the reset to default operation is already completed. This will take around 20 seconds from power up. You may then release the reset button.
ACM-3001 Hardware User’s Manual •1 Digital Input - An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. The device will detect the change in digital input and transmit the signal to video surveillance servers.
ACM-3001 Hardware User’s Manual Installation Procedure Ceiling Mount Use the drill template, and drill a hole with φ35 on the ceiling Tighten the plate to ceiling with M4*20 screws 11 www.acti.
ACM-3001 Hardware User’s Manual Connect cables through the hole on the ceiling and plate, or on the side of casing Fasten the camera to ceiling by turning clockwise direction 12 www.acti.
ACM-3001 Hardware User’s Manual Insert the cables (Power/Network/DIO/Audio) through the mounting plate and connect to the camera. Then use the little strap in bundled accessory to fasten the network cable. 1.6.1.6 Done 13 www.acti.
ACM-3001 Hardware User’s Manual Wall Mount Tighten wall mount bracket to the wall by 3 PAN Head Tapping screws 3-PAN HEAD SCREW TAPPING Tighten the plate to wall mount bracket with M4*10 screws, and connect all necessary cables through the hole on the plate and wall mount kit 2-FLAT HEAD SCREW TAPPING(M4x10) 14 www.acti.
ACM-3001 Hardware User’s Manual Note: that there’s a triangle mark on both plate and wall mount kit. Those triangle marks need to be fixed to the same direction. Insert the cables (power/Network/audio) through the mounting plate and connect to the camera. Then use the little strap in bundled accessory to fasten the network cable. 15 www.acti.
ACM-3001 Hardware User’s Manual Fasten the camera to wall mount kit by turning clockwise direction Done 16 www.acti.
ACM-3001 Hardware User’s Manual Basic Connections Follow the procedures below to connect the IP PoE Fixed Dome Camera to the respective apparatuses. If you have a PoE(Power over Ethernet) supported switch or injector: 1) Connect your IP Camera to the Switch / Injector by CAT5 or CAT6 cables with RJ45 connector. 2) Connect your Switch / Injector to PC with another CAT5 / CAT6 network cable.
ACM-3001 Hardware User’s Manual Please refer our PoE Guide for more details on Power over Ethernet related concepts. Product Specification ACM-3001 Device Image Micron Progressive Scan CMOS Size 1/3 inch Effective Pixels Min. Scene Illumination 640(H) x 480(V) Color 0.5 Lux at F1.0 (2400 ºK, 30 IRE) B/W N/A IR Sensitivity N/A CDS Sensor N/A Focal Length f4.2 mm / F1.8 Viewing Angle 63.7º (Horizontal) Camera Angle Adjustment X (Panning) Y (Tilting) 0º ~90º Synchronization Sync.
ACM-3001 Hardware User’s Manual 2. Accessing Camera If you have DHCP server / router in your network: Many network server / routers are able to automatically provide IP addresses through DHCP. If you are using such a network, just plug in your computer and IP Camera into the network and your IP PoE Fixed Dome Camera will acquire network address by itself. Find and access the device with our IP Utility program. You may download it at: http://www.acti.
ACM-3001 Hardware User’s Manual Please set the settings as below. IP address: 192.168. 0.xxx Subnet mask: 255.255.255.0 (NOTE: xxx should be a number from 1 to 254 except 100, which is used by the IP PoE Fixed Dome Camera. Please also make sure that no two equipments use the same IP address in the same network.) 4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP: 192.168.0.100 5.
ACM-3001 Hardware User’s Manual If you are using a single camera, this is enough to access the device. If you are using multiple devices, you need to change the current device to another unused IP address, so that when the next device is connected to the network, no two devices use the same IP. Please perform the following steps. 7. Go to Setup -> WAN Setting 8. Choose Static IP Address. 9. Change the IP to 192.168.0.101 or any other unused IPs. Do NOT use the PC’s IP address or 192.168.0.100.).
ACM-3001 Hardware User’s Manual 10. Click “Apply” 11. Please go to Save Reboot, and click ”Apply”. Internet Explorer will close after a few seconds. This is normal. 12. Wait for 30 seconds, and open IE again to connect to the new IP. (In this example, 192.168.0.101). For the second device or more you add into the network, please type the correct IP. 13. Adjust the video stream by going to Video Setting 22 www.acti.
ACM-3001 Hardware User’s Manual 23 www.acti.
