ACM-4201 Megapixel IP PoE Cube Camera with PIR Hardware User’s Manual (DC 12V / PoE) Ver.
ACM-4201 Hardware User’s Manual Table of Contents 0. Precautions 3 1. Introduction 4 Package Contents ........................................................................... 4 Features and Benefits ..................................................................... 5 Safety Instructions .......................................................................... 6 Physical description ........................................................................ 8 Basic Connections ....................
ACM-4201 Hardware User’s Manual 0. Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.
ACM-4201 Hardware User’s Manual 1. Introduction Package Contents ACM-4201 Product CD Warranty Card Camera Stand Accessories 4 www.acti.
ACM-4201 Hardware User’s Manual Features and Benefits This is a cutting-edge digital video surveillance camera. It can compress and transmit real time images with outstanding image quality (8 FPS @ SXGA, 1280x1024) through a standard TCP/IP network. This camera is your best choice to build an intelligent IP surveillance system. MPEG-4/MJPEG Dual Codec Compression This device supports two compression formats, MPEG-4 and MJPEG.
ACM-4201 Hardware User’s Manual Safety Instructions Don’t use the power supply with other voltages This device is likely to be damaged or damage other equipments / personnel, if you use a power supply with different voltage than the one included with this device. All warranty of this product will be voided in the situations above. Don’t open the housing of the product Cleaning Disconnect this video product from the power supply before cleaning.
ACM-4201 Hardware User’s Manual improper adjustment of other controls may result in damage, and will often require extensive work by a qualified technician to restore the video product to its normal operation. Safety Check Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine if the video product is in proper operating condition. 7 www.acti.
ACM-4201 Hardware User’s Manual Physical description 1) Action LED Indicator LED light will light up after the Camera has successfully completed the boot process. 2) Microphone Input Sensitivity: -36dB ± 3dB (0dB=1V/Pa at 1KHz) S/N Ratio: More than 58dB Directivity: Omni directional 3) Motion Sensor (PIR) * Motion Sensor detects movement by looking at changes in the Infrared (IR) spectrum. * Available only for device versions with enhancements 8 www.acti.
ACM-4201 Hardware User’s Manual 4) Audio Output The IP device supports audio output with earphone jack 5) Ethernet Port The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this IP device can auto detect the speed of local network segment (10Base-T/100Base-TX Ethernet). 6) DV 12V Power Input Connect the power adaptor here if your power input is DC12V.
ACM-4201 Hardware User’s Manual DC TO DC FUSE 1A 1 CONVERTER + 3.3V 2 3 - POWER INPUT EARTH GND GND DC POWER DI DI DO SW 1 RELAY 2 3 DIODE DEVICE 4 NPN DO CAMERA Connect input/output devices to the camera as follows: 1. Attach the cables for the device securely to the supplied green connector block. 2. Once the cables are connected, push the connector block into the terminal connector (also green) on the camera.
ACM-4201 Hardware User’s Manual Basic Connections Follow the procedures below to connect the IP device to the respective apparatuses. If you have a PoE (Power over Ethernet) supported switch or injector: (PoE Enabled version only) 1) Connect your IP Camera to the Switch / Injector by CAT5 or CAT6 cables with RJ45 connector. 2) Connect your Switch / Injector to PC with another CAT5 / CAT6 network cable.
ACM-4201 Hardware User’s Manual Product Specification Image Device Size Effective Pixels ACM-4201 Micron Progressive Scan CMOS 1/3 inch 1280(H) x 1024(V) Min. scene Illumination Color 0.5 Lux at F1.0 (2400°K, 30 IRE) Lens Viewing Angle Synchronization Sync. System Motion Detection Electronic shutter Lens Fixed Shutter (Manual) Functions Flickerless BLC AGC White Balance S/N Ratio S/N Ratio Compression Picture Resolution Video Compression Bit Rate f4.2mm / F1.
ACM-4201 Hardware User’s Manual 2. Accessing Camera If you have DHCP server / router in your network: Many network server / routers are able to automatically provide IP addresses through DHCP. If you are using such a network, just plug in your computer and IP Camera into the network and your IP device will acquire network address by itself. Find and access the device with our IP Utility program. You may download it at: http://www.acti.
ACM-4201 Hardware User’s Manual 4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP: 192.168.0.100 5. When you see the login window, please input default user and password: Default User: Admin Password: 123456 6. After logging in, you will see the video from camera. To go to the main menu, click the ”Setup” button on the top left. If you are using a single camera, this is enough to access the device. 14 www.acti.
ACM-4201 Hardware User’s Manual If you are using multiple devices, you need to change the current device to another unused IP address, so that when the next device is connected to the network, no two devices use the same IP. Please perform the following steps. 7. Go to Setup -> WAN Setting 8. Choose Static IP Address. 9. Change the IP to 192.168.0.101 or any other unused IPs. Do NOT use the PC’s IP address or 192.168.0.100.).
ACM-4201 Hardware User’s Manual 12. Wait for 30 seconds, and open IE again to connect to the new IP. (In this example, 192.168.0.101). For the second device or more you add into the network, please type the correct IP. 13. Adjust the video stream by going to Video Setting 16 www.acti.